Aerohive AP390

Aerohive AP390 Bedienungsanleitung

  • Aerohive QuickStart for the AP370 and AP390
    This guide explains how to install Aerohive AP370 or AP390 access points and connect
    to HiveManager. The instructions in this document apply to both models. To register, get
    the latest product documentation, (including translations of select documents), see
    compliance information, and download software updates, visit
    2013 Aerohive Networks Inc.
    is a U.S. registered trademark of Aerohive Networks Inc.
    P/N 330102-03 Rev. A
    You can mount the AP370 or AP390 on a dust-free surface, on a wall, or to the
    tracks of a dropped ceiling grid that will support its weight. The wall and ceiling
    mounting options are explained below and on the next panel.
    Mounting the AP370 and AP390
    Cut a small hole in the ceiling tile to accommodate the cables. Connect the
    cables and, for optimal reception, align external antennas for the AP390 as
    shown in the next section.
    The status LED on the top of the device displays the following activity states:
    Dark: Power is off, or the indicator has been disabled.
    Amber (ashing): The device is performing a rmware upgrade. Do not
    power off the device during this process.
    Amber (solid): This indicates that the CAPWAP connection has not been
    successfully established, or the device is booting or shutting down.
    White: The device is powered on and operating properly, and has made a
    successful CAPWAP connection through the ETH0 interface.
    Status LED
    You can mount the AP370 or AP390 on a at surface using the rubber feet
    that ship with the device. You can also mount these devices to the tracks
    of a dropped ceiling grid using the mounting tabs and clips on the back
    of the device. The tabs slip over the edge of the ceiling track and the clips
    click into place to secure the device.
    The ceiling mounting options are shown below. The mounting hardware on
    the device allows you to mount it diagonally, or square to the track.
    Ceiling Mount
    To mount the device on a ceiling track in either the diagonal or square position,
    hold the device so that you are touching the appropriate tabs (as shown in the
    previous illustrations). Hold the device upside down and press it gently against
    the ceiling track. Use your ngers to guide one of the tabs over the edge of the
    track. Then rotate the device until the clips click into place.
    To remove the device, press the clips toward the device until they disengage
    from the track, then rotate the device gently and pull it away from the track.
    The illustrations below show how to install the device on a ceiling track in the
    diagonal position. To mount the device the square position, use the square-
    mount tabs and clips and follow the same steps (except for the rotation, which
    will be in the opposite direction).
    Use your ngertips to align the
    tabs with the track.
    Rotate the device until
    the clips click into place.
    You can secure the AP using a Kensington lock, or you can use the security
    bracket and screw that ships with the device to secure it to a ceiling track or to
    a wall, as shown in the illustrations below. To use a Kensington lock, loop the lock
    cable around a secure object, insert the T-bar component of the lock into the
    lock slot on the AP and then turn the key to engage the lock.
    To secure the AP to a ceiling track or a wall using the security bracket and screw,
    you will need a spanner bit for size #6 security screws, and a driver that will
    accept the bit. Bits are available from Aerohive in sets of three (AH-ACC-SEC-BIT-
    300-100-3PK). To use the security screw, refer to the illustrations below. If you use
    the cross-head screw, you will need a cross-head screwdriver.
    Aerohive recommends a variety of Kensington locks. For more information,
    contact your sales representative.
    Locking the Device
    Diagonal mount
    lock slot
    Square mount
    lock slot
    lock slot
    Guide security bracket along the
    lock slot until the screw holes align
    and the end of the bracket slips
    under the clip.
    Aligning AP390 External Antennas
    Ceiling track
    Diagonal installation
    Square installation
    Attach the AP to any surface that supports its weight
    (less than 1 lb or .45 kg for either device), and to which
    you can install the wall mount screws. There are four
    wall mount slots on the back of the device. Measure
    the distances between the centers of the large ends of
    these slots and drill corresponding holes in the wall. Install
    the 3 wall mount screws and plastic anchors that ship
    with the device. If you are connecting to cables from
    inside the wall, drill a hole in the wall so that you can pass
    the cables through to the AP. Finally, connect the cables
    to the device.
    Wall Mount
    Wall mount slots
    mount clip
    and tab
    mount clip
    and tab
    mount clip
    and tab
    mount clip
    and tab
    After you power on the AP, it automatically tries to get network settings and contact
    HiveManager. This process takes about ve minutes. When you see the AP listed on
    the All Devices page in the Monitor section of the HiveManager GUI, the initial setup is
    complete and you can begin managing the AP with HiveManager.
    If the AP does not appear after about ten minutes, see the Aerohive product
    documentation and computer-based training modules to learn what you can do to
    help establish the connection. These resources are available for free at
    Some other network devices (They
    might all be incorporated in the same
    device, such as a router or firewall.)
    Connect a standard
    RJ45 Ethernet cable
    from ETH0 on the AP to
    a switch.
    For AP390 models, attach external antennas
    to the 5 GHz and 2.4 GHz connectors.
    Connecting the Device
    If the switch provides
    PoE, cabling the AP to the
    switch will cause the AP to
    power on in a few seconds.
    If the switch does not provide PoE,
    use the AC/DC power adaptor, power
    supply, or PoE injector (all available
    as accessories).
    AP370 Kit Contents
    • AP370 device with USB slot cover
    • 2 security screws
    • 2 slotted screws
    • 3 wall mount screws and anchors
    • 1 security bracket
    • 4 adhesive feet
    • QuickStart Guide
    Optional Accessories
    You can order a wide variety of accessories for AP370 and AP390 devices.
    For specic information about the accessories that are available, contact
    your sales representative.
    0° to wall
    90° to
    WARNING: FOR INDOOR USE ONLY. The AP370 and AP390 devices, DC power
    adapter and all connected cables are designed for indoor use only.
    mount clip
    mount clip
    Diagonal mount tab
    (under fingertip)
    Diagonal mount
    tab (under
    Note: For a square mount,
    rotate in the opposite
    (Antennas ordered separately)
    AP390 Kit Contents
    • AP390 device with USB slot cover
    • 2 security screws
    • 2 slotted screws
    • 3 wall mount screws and anchors
    • 1 security bracket
    • 4 adhesive feet
    • QuickStart Guide
    Power specications for the AP370 and AP390:
    •Power adapter: DC 12V, 2A
    •PoE: DC 55V, 0.6A, Class III
    Power Specications
Aerohive AP390

Brauchen Sie Hilfe?

Anzahl der Fragen: 0

Haben Sie eine Frage zum Aerohive AP390 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere Aerohive AP390-Eigentümer Ihre Frage richtig beantworten.

Sehen Sie sich hier kostenlos das Handbuch für Aerohive AP390 an. Dieses Handbuch fällt unter die Kategorie Zugangspunkte und wurde von 1 Personen mit einem Durchschnitt von 8.7 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Aerohive AP390 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Aerohive AP390-Spezifikationen

Marke Aerohive
Model AP390
Produkte Zugangspunkt
Sprache Englisch
Dateityp PDF
Maximale Datenübertragungsrate 1300
2,4 GHz
5 GHz
Ethernet LAN Datentransferraten 10, 100, 1000
Netzstandard IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3af, IEEE 802.3at
Modulation 256-QAM, DSSS, OFDM
Spread-Spectrum Methode DSSS
Anschlüsse und Schnittstellen
Anzahl Ethernet-LAN-Anschlüsse (RJ-45) 3
Anzahl USB 2.0 Anschlüsse 1
Unterstützte Sicherheitsalgorithmen 802.1x RADIUS, TKIP, WEP, WPA, WPA2
Anzahl der Antennen 6
Antennenfunktionen Abnehmbare Antenne
Ausgangsspannung 12
Eingangsspannung 100 - 240
Ausgangsstrom 2
Power over Ethernet (PoE)
Produktfarbe Weiß
Platzierung Ceiling, Table, Wall
Slot-Typ Kabelsperre Kensington
Luftfeuchtigkeit in Betrieb -20 - 55
Temperaturbereich in Betrieb -40 - 80
Gewicht und Abmessungen
Breite 195.07
Höhe 195.07
Gewicht 680
Tiefe 55.88

Auf der Suche nach einer Bedienungsanleitung? sorgt dafür, dass Sie in Windeseile die Bedienungsanleitung finden, die Sie suchen. In unserer Datenbank befinden sich mehr als 1 Million PDF Bedienungsanleitungen von über 10.000 Marken. Jeden Tag fügen wir die neuesten Bedienungsanleitungen hinzu, damit Sie jederzeit das Produkt finden, das Sie suchen. Es ist ganz einfach: Tippen Sie in der Suchleiste Markenname und Produkttyp ein und Sie können direkt die Bedienungsanleitung Ihrer Wahl gratis online einsehen.

© Copyright 2020 Alle Rechte vorbehalten.

Diese Website benutzen Cookies. Wenn Sie die Website weiter nutzen, stimmen Sie der Verwendung von Cookies zu.

Erfahren Sie mehr