Max temperature range: -45 ºC to +70 ºC (-50 ºF to +160 ºF)
Water resistance: Submersible to 25 m (80 ft)
1.3 LOCATION AND DESCRIPTION OF MAJOR COMPONENTS
See g. 1
1. Sight
2. Battery Cap
3. Battery (DL1/3N or similar)
4. Rotary Switch
5. Cap Adjustment (2 pcs)
6. Strap (for Cap Adjustment, 2 pcs)
7. Adjustment Screws Windage/Elevation (2 pcs)
8. Lens Cover, rear
9. Lens Cover, front
*NVD: Night Vision Device
**MOA: Minute Of Angle 1MOA ≈ 30 mm at 100 meters ≈ 1” at 100 yards
***Average values, depending on brightness setting
CHAPTER II – OPERATION UNDER NORMAL CONDITIONS
2.1 ASSEMBLY AND PREPARATION FOR USE
WARNING: Ensure that the weapon is unloaded and the safety selector
is in the ”safe” position before attempting to install, remove or perform
maintenance on the sight.
2.1.1 Installing Battery
a. Remove battery cap (2) by turning it counter clockwise.
b. Insert battery (3) with positive (+) end toward cap.
CAUTION: When replacing battery (not necessary when the sight is unused),
check that the O-ring is present and not damaged. Failure to do so could
result in water leakage into the battery compartment.
c. Install battery cap (2) by turning clockwise until snug. Hand tighten only.
Using tools can damage equipment.
d. Verify that the red dot is present by turning the rotary switch clockwise.
2.1.2 Installing Ring and Sight on the weapon
Aimpoint’s sights are designed for installation on most types of weapons.
If your weapon does not have or support an appropriate base(s), please
consult your dealer, gunsmith or other qualied source.
a. Assemble the sight to the weapon by using Aimpoint´s wide 30 mm ring
or QR-mount. If other standard 30 mm rings are used, make sure that the
ring(s) covers a length of minimum 25 mm or 1” (two standard rings could
possibly be used).
b. Ensure that the sight is correctly positioned for right or left hand shooting.
(Aimpoint sights can be installed to support either right hand (g 2) or left
hand (g 3) shooters.)
c. When using lens covers (8 & 9), ensure that they are correctly positioned
and can be opened.
NOTE: make sure that you have space between the bottom front part of the
sight and the top of the base/weapon.
d) Finally, make sure that all screws are rmly tightened around the sight.
e) Complete the zeroing (2.2.1).
1
2
3
6
7
5
5
7
6
4
8
9
Right-handed shooter
conguration
Comp M2/ML2
Left-handed shooter
conguration
Fig. 2
Fig. 1
Fig. 3
Sehen Sie sich hier kostenlos das Handbuch für Aimpoint CompM2 an. Dieses Handbuch fällt unter die Kategorie Nicht kategorisiert und wurde von 1 Personen mit einem Durchschnitt von 5.3 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Aimpoint CompM2 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage
Brauchen Sie Hilfe?
Haben Sie eine Frage zum Aimpoint und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Aimpoint -Besitzer, Ihnen eine gute Antwort zu geben.
Brauchen Sie Hilfe?
Haben Sie eine Frage zum Aimpoint und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Aimpoint -Besitzer, Ihnen eine gute Antwort zu geben.
Anzahl der Fragen: 0