Name: Boss BD-2
Brand: Boss
SKU: 1388675
Rating: 75 (1 reviews)

BedienungsanleitungBoss BD-2

INPUT jack

This jack accepts input signals (coming from a guitar, some other musical

instrument, or another eects unit).

AC Adaptor

(PSA series; sold separately)

Electric Guitar

English

LEVEL knob

This adjusts the volume of the eect sound.

* When this knob is turned counterclockwise, no sound will be heard.

7 The BD-2 is the overdrive that has been specically designed for crunch distortion.

7 It can faithfully express the tone change caused by moving the knobs on the guitar.

7 It can create distortion that can faithfully reproduce the picking nuance of the player.

7 It can create wide varieties of distortions from crunch to hard distortion, by adjusting the Gain Knob.

7 Even if the Gain Knob is raised, a clean and natural sound can be produced by turning the volume of the guitar.

7 A natural-sounding overdrive continues to be produced without any loss in its quality, even if you turn down the volume on your guitar.

OUTPUT jack

The output jack is used to connect the unit to

ampliers or other devices.

Guitar Amplier

DC IN jack

Accepts connection of an AC Adaptor (PSA series; sold separately). By using an AC Adaptor, you can play

without being concerned about how much battery power you have left.

* We recommend that you keep batteries installed in the unit even though you’ll be powering it with

the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the AC adaptor

gets accidentally disconnected from the unit.

* Use only the specied AC adaptor (PSA-series).

* If the AC adaptor is connected while power is on, the power supply is drawn

from the AC adaptor.

CHECK indicator

This indicator shows whether an eect is ON/OFF, and doubles as the Battery Check indicator.

The indicator lights when an eect is ON.

* If this indicator goes dim or no longer lights while an eect is ON, the battery is near

exhaustion and should be replaced immediately.

TONE knob

This adjusts the tone of sound. Rotating it clockwise will create sharp sound with

emphasized treble, while turning it counterclockwise will create soft sound with

cut treble.

Pedal Switch

This switch turns the eects ON/OFF.

Precautions When Connecting

To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

Once everything is properly connected, be sure to follow the

procedure below to turn on their power. If you turn on equipment

in the wrong order, you risk causing malfunction or equipment

failure.

When powering up: Turn on the power to your guitar amp last.

When powering down: Turn o the power to your guitar amp rst.

Before turning the unit on/o, always be sure to turn the volume

down. Even with the volume turned down, you might hear some

sound when switching the unit on/o. However, this is normal and

does not indicate a malfunction.

Use of Battery

* A battery was installed in the unit before it left the factory. The

life of this battery may be limited, however, since its primary

purpose was to enable testing.

* If you handle batteries improperly, you risk explosion and uid

leakage. Make sure that you carefully observe all of the items

related to batteries that are listed in “USING THE UNIT SAFELY”

and “IMPORTANT NOTES” (supplied on a separate sheet).

* When operating on battery power only, the unit’s indicator will

become dim when battery power gets too low. Replace the

battery as soon as possible.

* Batteries should always be installed or replaced before

connecting any other devices. This way, you can prevent

malfunction and damage.

Main Specications

Nominal Input Level -20 dBu

Input Impedance 1 MΩ

Nominal Output

Level

-20 dBu

Output Impedance 1 kΩ

Recommended Load

Impedance

10 kΩ or greater

Power Supply Carbon-zinc battery (9 V, 6F22) or

Alkaline battery (9 V, 6LR61)

AC adaptor (PSA series: sold separately)

Current Draw 20 mA

* Expected battery life under continuous use:

Carbon: 24.5 hours

Alkaline: 44 hours

These gures will vary depending on the

actual conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight 360 g / 13 oz (including battery)

Accessories Leaet (“USING THE UNIT SAFELY,” “IMPORTANT

NOTES,” and “Information”)

Carbon-zinc battery (9 V, 6F22)

Options

(sold separately)

AC adaptor (PSA-series)

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the

time that the document was issued. For the latest information,

refer to the Roland website.

GAIN knob

This adjusts the gain of the blues driver. Rotating the knob clockwise will

increase the gain creating harder distortion.

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

Main Features

Panel Descriptions

Owner’s Manual

* The INPUT jack doubles as the power switch.

Power to the unit is turned on when you plug

into the INPUT jack; the power is turned o when

the cable is unplugged. To prevent unnecessary

battery consumption, be sure to disconnect the

plug from the INPUT jack when not using the

eects unit.

Thumbscrew

When this screw is loosened, the pedal will open, allowing you to change the

battery.

* For instructions on changing the battery, refer to “Changing the Battery.”

Operating the Unit

1. When you have made the necessary connections, set

the knobs as shown in the illustration.

2. Depress the pedal switch to turn the eect on. (Make

sure that the CHECK Indicator lights.)

3. Adjust the gain of the Dry or Overdrive sound using

the GAIN knob.

4. Adjust the tone using the TONE knob.

5. Adjust the output level using the LEVEL knob.

Changing the Battery

Thumbscrew

Battery Housing

Pedal

Spring Base

Coil Spring

Guide Bush

Hole

Battery Snap

Cord

Battery

Snap

9 V Battery

1. Hold down the pedal and loosen the thumbscrew, then

open the pedal upward.

* The pedal can be opened without detaching the thumbscrew

completely.

2. Remove the old battery from the battery housing, and

remove the snap cord connected to it.

3. Connect the snap cord to the new battery, and place

the battery inside the battery housing.

* Be sure to carefully observe the battery’s polarity (+ versus -).

4. Slip the coil spring onto the spring base on the back of

the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil

spring, and battery housing.

5. Finally, insert the thumbscrew into the guide bush

hole and fasten it securely.

Sehen Sie sich hier kostenlos das Handbuch für Boss BD-2 an. Dieses Handbuch fällt unter die Kategorie nicht kategorisiert und wurde von 1 Personen mit einem Durchschnitt von 7.5 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Boss BD-2 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Brauchen Sie Hilfe?

Haben Sie eine Frage zum Boss und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Boss -Besitzer, Ihnen eine gute Antwort zu geben.

Anzahl der Fragen: 0