Boss Metal Zone MT-2WÙ Bedienungsanleitung

Boss Metal Zone MT-2WÙ
7.5 · 1
PDF Bedienungsanleitung
 · 1 Seite
BedienungsanleitungBoss Metal Zone MT-2WÙ
* 5 1 0 0 0 6 3 4 9 2 - 0 2 *

Owner’s Manual

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

AC Adaptor
(PSA series; sold separately)
Electric Guitar


This knob controls the tone of the eect sound at lower frequencies. Rotating the
knob clockwise boosts the lower frequencies, while rotating it counterclockwise
cuts the lower frequencies. The lower frequencies have a variable range of ±15 dB.


This knob controls the tone of the eect sound at higher frequencies. Rotating the
knob clockwise boosts the higher frequencies, while rotating it counterclockwise
cuts the higher frequencies. Higher frequencies have a variable range of ±15 dB.
5 This is a WAZA CRAFT series eect pedal crafted with a high-quality analog original circuit design.
5 This unit produces a wide range of harmonically rich and powerful high-gain distortion sounds.
5 This unit also includes a Custom setting providing an even broader range of dynamics and response.


Use this 1/4” output jack to connect to the input of
your guitar amplier or the input of additional eect
Guitar Amplier

DC IN jack

In addition to 9-volt battery operation, this unit can also operate on a 9-volt AC adaptor (BOSS PSA series;
sold separately).
* Use only the specied AC adaptor (PSA series; sold separately), and connect it to an AC outlet

of the correct voltage.

* If the AC adaptor is connected while a battery is installed, the power supply is drawn from the

AC adaptor.

CHECK indicator

This indicator shows whether an eect is ON/OFF, and doubles as the Battery Check indicator.
The indicator lights when an eect is ON.

* The brightness of the CHECK indicator (LED) will dim as the battery lowers. Replace

the battery when the LED is dim or does not light. For instructions, refer to “Changing

the Battery.”

* The CHECK indicator shows whether the eect is on or o, and indicates the dierent

functions. It does not indicate whether the power to the device is on or not.

Pedal switch

This switch turns the eects ON/OFF.


When this screw is loosened, the pedal will open, allowing you to change the

* For instructions on changing the battery, refer to “Changing the


Panel Descriptions

Main Features

Precautions When Connecting

* To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any


* Once the connections have been completed, turn on power

to your various devices in the order specied. By turning on

devices in the wrong order, you risk causing malfunction and/

or damage to speakers and other devices.

When powering up: Turn on the power to your guitar amp last.
When powering down: Turn o the power to your guitar amp rst.

* Before turning the unit on/o, always be sure to turn the

volume down. Even with the volume turned down, you might

hear some sound when switching the unit on/o. However,

this is normal and does not indicate a malfunction.

Use of Battery

* The life of the included battery may be limited as its primary

purpose was for testing during assembly.

* If you handle batteries improperly, you risk explosion and uid

leakage. Make sure that you carefully observe all of the items

related to batteries that are listed in “USING THE UNIT SAFELY”

and “IMPORTANT NOTES” (supplied on a separate sheet).

* When operating on battery power only, the unit’s indicator will

become dim when battery power gets too low. Replace the

battery as soon as possible.

* Batteries should always be installed or replaced before

connecting any other devices. This way, you can prevent

malfunction and damage.

Changing the Battery

1. Hold down the

pedal and loosen

the thumbscrew,

then open the

pedal upward.

* The pedal can be
opened without
detaching the

2. Remove the old

battery from the

battery housing,

and remove the snap cord connected to it.

3. Connect the snap cord to the new battery, and place

the battery inside the battery housing.

* Be sure to carefully observe the battery’s polarity (+ versus -).

4. Slip the coil spring onto the spring base on the back of

the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil spring, and
battery housing.

5. Finally, hold down the pedal while tightening the

thumbscrew into the guide bush hole.

Main Specications

BOSS MT-2W: Metal Zone
Nominal Input Level -20 dBu
Input Impedance 1 MΩ
Nominal Output Level -20 dBu
Output Impedance 1 kΩ
Recommended Load
10 kΩ or greater
Power Supply
DC 9 V: Alkaline battery (9 V, 6LR61),
Carbon-zinc battery (9 V, 6F22), AC adaptor
(sold separately)
Current Draw
35 mA
* Expected battery life under continuous
Alkaline battery: Approx. 18 hours
Carbon-zinc battery: Approx. 7 hours
These gures will vary depending on the
actual conditions of use.
73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
(including battery)
440 g
1 lb
Owners Manual, Leaet (“USING THE
“Information”), Alkaline battery (9 V, 6LR61)
(sold separately)
AC adaptor (PSA-series)

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the

time that the document was issued. For the latest information,

refer to the Roland website.

* Roland, BOSS, METAL ZONE, and

WAZA CRAFT are either

registered trademarks or trademarks of Roland Corporation in

the United States and/or other countries.

Battery Housing
Spring Base
Coil Spring
Guide Bush
Battery Snap
© 2018 Roland Corporation


This knob adjust the frequency of the Middle knobs gain. Rotating the knob
clockwise increases the frequency center point. At Max the frequency center is 5
kHz. Rotating the knob counterclockwise decreases the frequency center point.
At Minimum the frequency center is 200 Hz.


This knob boosts or cuts the frequency you set with the EQUALIZER MID FREQ
knob. Rotating the knob clockwise boosts the level of the middle frequencies,
while rotating it counterclockwise cuts the level of the middle frequencies.

* When the EQUALIZER MIDDLE knob is set to the center position, the

EQUALIZER MID FREQ knob does not aect the sound.

DIST knob

Rotating the knob clockwise increases the gain and distortion eect.

* If you set this knob too high, the noise will increase and oscillation

may occur.

LEVEL knob

This knob adjusts the volume of the eect sound.

* No sound will be heard when this knob is rotated completely


INPUT jack

This jack accepts input signals (coming from a guitar, some other musical
instrument, or another eects unit).

* The INPUT jack also serves as the power

switch. Power is turned on whenever a plug

is inserted into the INPUT jack, and is turned

o when the plug is disconnected. When

not using the unit, you should disconnect

any cord connected to the INPUT jack.

Mode switch

Switches the sound variation.
S (Standard)
Reproduces the original MT-2 sound by a newly
crafted all analog circuit.
C (Custom)
Produces a custom sound which is ne-tuned for
broader range of dynamics and response.

Sehen Sie sich hier kostenlos das Handbuch für Boss Metal Zone MT-2WÙ an. Dieses Handbuch fällt unter die Kategorie Nicht kategorisiert und wurde von 1 Personen mit einem Durchschnitt von 7.5 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Boss Metal Zone MT-2WÙ oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Brauchen Sie Hilfe?

Haben Sie eine Frage zum Boss und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Boss -Besitzer, Ihnen eine gute Antwort zu geben.

Anzahl der Fragen: 0

Metal Zone MT-2WÙ | MT-2W
Nicht kategorisiert
Benutzerhandbuch (PDF)
ProduktfarbeBlack, Grey
Beste VerwendungGitarre
Ausgangspegel-20/0 dB
Nominales Input level-20 dB
Synchronisations-Eingangsimpedanz1000000 Ohm
Output Widerstand1000 Ohm
Rutschfeste OberflächeJa
Anschlüsse und Schnittstellen
6,35 mm (1/4-Zoll) Ausgang1
6,35 mm (1/4-Zoll) Eingang1
Gleichstrom-Anschluss (DC)Ja
EnergiequelleAC, Battery
Energieverbrauch35 mA
Anzahl unterstützter Akkus/Batterien1
Akku-/Batteriespannung9 V
Gewicht und Abmessungen
Breite73 mm
Tiefe129 mm
Höhe59 mm
Gewicht440 g
Mehr anzeigen

Finden Sie die Antwort auf Ihre Frage nicht im Handbuch? Vielleicht finden Sie die Antwort auf Ihre Frage in den FAQs zu Boss Metal Zone MT-2WÙ unten.

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Keine Ergebnisse

© Copyright 2023 Alle Rechte vorbehalten.