Casio Edifice EQW-M710DB-1A1ER Bedienungsanleitung

Casio Edifice EQW-M710DB-1A1ER
8.2 · 10
PDF Bedienungsanleitung
 · 6 Seiten
BedienungsanleitungCasio Edifice EQW-M710DB-1A1ER

Operation Guide 5089

Congratulations upon your selection of this CASIO watch.
This watch does not have a city code that corresponds to the UTC offset of –3.5
hours. Because of this, the radio-controlled atomic timekeeping function will not
display the correct time for Newfoundland, Canada.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any
damage or loss suffered by you or any third party arising through the use of this
product or its malfunction.

About This Manual

Button operations are indicated using the letters A through
D shown in the illustration.
Hand Functions
z Hour Hand
x Second Hand
c Minute Hand
v Left Dial Hand:
Indicates the current day of the week and current mode.
b 24-hour Hand:
Indicates the current 24-hour timekeeping hour.
The long end indicates the current hour between 18:00
and 6:00. The short end indicates the current hour
between 6:00 and 18:00.
n Right Dial Hands: Indicate a time, in 24-hour format, depending on the current
m Day
This User’s Guide uses numbers shown above to identify watch hands and indicators.

Things to check before using the watch

1. Hold down C for about two seconds to enter the Timekeeping Mode, and
then observe the movement of the
x Second Hand.
Is the x Second Hand moving smoothly at one-second intervals?
Is the x Second Hand moving at
two-second intervals or is it stopped
Go to step 2.
The watch is charged sufficiently.
For details about charging, see
“Charging the Watch”.
Power is low. Charge the watch by placing
it in a location where it is exposed to light.
For details, see “Charging the Watch”.
2. Check the Home City and the daylight saving time (DST) setting.
Use the procedure under “To configure Home City settings” to configure your Home
City and daylight saving time settings.
Proper time calibration signal reception and World Time settings depend on correct
Home City, time, and date settings in the Timekeeping Mode. Make sure you
configure these settings correctly.
3. Set the current time.
To set the time using a time calibration signal
See “To get ready for a receive operation”.
To set the time manually
See “Configuring Current Time and Date Settings Manually”.
The watch is now ready for use.
For details about the watch’s radio controlled timekeeping feature, see “Radio
Controlled Atomic Timekeeping”.

Charging the Watch

The face of the watch is a solar cell that generates power from light. The generated
power charges a built-in rechargeable battery, which powers watch operations. The
watch charges whenever it is exposed to light.
Charging Guide
Whenever you are not
wearing the watch, leave
it in a location where it is
exposed to light.
Best charging
performance is achieved
by exposing the watch to
light that is as strong as
When wearing the watch,
make sure that its face is
not blocked from light by the
sleeve of your clothing.
The watch may enter a
sleep state if its face is
blocked by your sleeve
even only partially.
Leaving the watch in bright light for charging can cause it to become quite hot.
Take care when handling the watch to avoid burn injury. The watch can become
particularly hot when exposed to the following conditions for long periods.
On the dashboard of a car parked in direct sunlight
Too close to an incandescent lamp
Under direct sunlight
B +
* 6> 5
Keep the watch in an area normally exposed to bright light when storing it for long
periods. This helps to ensure that power does not run down.
Storing the watch for long periods in an area where there is no light or wearing it in
such a way that it is blocked from exposure to light can cause power to run down.
Make sure that the watch is exposed to bright light whenever possible.
Power Levels
You can get an idea of the watch’s power level by
observing the movement of the
x Second Hand in the
Timekeeping Mode.
If the
x Second Hand is moving normally at one-second
intervals, power is at Level 1.
If the
x Second Hand is moving at two-second intervals,
power is at Level 2, which is quite low. Expose the watch
to light as soon as possible so it can charge.
Level Hand Movement Function Status
1 Normal. All functions enabled
x Second Hand moves at two-second
m Day changes to 1 (home position).
Beeper, time calibration signal
reception disabled
x Second Hand stopped.
z Hour Hand and c Minute Hand
stopped at 12 o’clock.
All functions disabled
When power drops to Level 3, all functions will be disabled but the watch will
continue to keep time internally for about one week. If you recharge the battery
sufficiently during this period, the analog hands will move automatically to the
correct setting and regular timekeeping will resume. After one week, all settings
(including timekeeping) will be cleared. Recharging the battery will reset all settings
to their initial factory defaults.
Power Recovery Mode
The watch is designed to go into a power recovery mode that stops hand operation
temporarily whenever power suddenly drops below a certain level due to overuse
of the alarm tone over a short period. Note that all operations are disabled while the
watch is in the power recovery mode.
The hands will move to the correct positions and the watch will resume normal
operation after power recovers (in about 15 minutes). Putting the watch in a location
where it is exposed to light will help power to recover sooner.
Charging Times
Exposure Level (Brightness)
Level Change *2
Level 3 Level 2 Level 1
Outdoor sunlight (50,000 lux) 8 minutes 2 hours 23 hours
Window sunlight (10,000 lux) 30 minutes 6 hours 90 hours
Window sunlight on cloudy day
(5,000 lux)
48 minutes 8 hours – – –
Indoor fluorescent lighting (500 lux) 8 hours 92 hours – – –
1 Approximate exposure each day to generate power for normal daily operation. *
2 Approximate exposure to take power up one level. *
The above times are for reference only. Actual times depend on lighting conditions.
For details about the operating time and daily operating conditions, see the “Power
Supply” section of the Specifications.
Power Saving
Power Saving enters a sleep state automatically whenever the watch is left for a
certain period in an area where it is dark. The table below shows how watch functions
are affected by Power Saving.
There actually are two sleep state levels: “second hand sleep” and “function sleep”.
Elapsed Time in Dark Operation
60 to 70 minutes (second hand sleep)
x Second Hand only stopped at 12 o’clock, all
other functions enabled
6 or 7 days (function sleep)
All functions, including analog timekeeping,
Internal timekeeping maintained
The watch will not enter a sleep state between 6:00 AM and 9:59 PM. If the watch
is already in a sleep state when 6:00 AM arrives, however, it will remain in the sleep
The watch will not enter a sleep state while it is in the Stopwatch Mode.
To recover from the sleep state
Move the watch to a well-lit area or press any button.

Radio Controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly.
However, when using the watch outside of areas covered by time calibration signals,
you will have to adjust the settings manually as required. See “Configuring Current
Time and Date Settings Manually” for more information.
This section explains how the watch updates its time settings when the city code
selected as the Home City is in Japan, North America, Europe, or China, and is one
that supports time calibration signal reception.
If your Home City code setting is this:
The watch can receive the signal from the
transmitter located here:
LON, PAR, ATH Anthorn (England), Mainflingen (Germany)
HKG Shangqiu City (China)
TYO Fukushima (Japan), Fukuoka/Saga (Japan)
HNL, ANC, LAX, DEN, CHI, NYC Fort Collins, Colorado (United States)
Moves at two-second
B +
@ 5

Sehen Sie sich hier kostenlos das Handbuch für Casio Edifice EQW-M710DB-1A1ER an. Dieses Handbuch fällt unter die Kategorie armbanduhren und wurde von 10 Personen mit einem Durchschnitt von 8.2 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Casio Edifice EQW-M710DB-1A1ER oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Brauchen Sie Hilfe?

Haben Sie eine Frage zum Casio und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Casio -Besitzer, Ihnen eine gute Antwort zu geben.

Anzahl der Fragen: 0

Die Casio Edifice EQW-M710DB-1A1ER ist eine Armbanduhr, die Präzision und Stil vereint. Mit ihrem Edelstahlgehäuse und -armband verleiht sie jedem Outfit einen eleganten Touch. Diese Uhr verfügt über eine Vielzahl von Funktionen, die sie zu einem vielseitigen Begleiter machen. Sie zeigt nicht nur die aktuelle Zeit an, sondern auch das Datum und den Wochentag. Darüber hinaus verfügt sie über eine weltweite Zeitzone-Funktion, mit der Sie die Zeit in verschiedenen Ländern ablesen können. Die Casio Edifice EQW-M710DB-1A1ER bietet auch eine Stoppuhr-Funktion, mit der Sie genaue Zeitmessungen durchführen können. Darüber hinaus verfügt sie über eine Alarmfunktion, die Sie daran erinnert, wichtige Termine einzuhalten. Der eingebaute Solarbetrieb ermöglicht es dieser Uhr, ihre Energie aus Licht zu beziehen, was für eine nachhaltige und umweltfreundliche Nutzung sorgt. Dies ist besonders praktisch, da Sie sich keine Gedanken über den Wechsel der Batterie machen müssen. Die Casio Edifice EQW-M710DB-1A1ER ist außerdem wasserdicht bis zu einer Tiefe von 100 Metern, was sie ideal für den täglichen Gebrauch und Aktivitäten im Wasser macht. Insgesamt ist die Casio Edifice EQW-M710DB-1A1ER eine hochwertige Armbanduhr, die Präzision, Funktionalität und stilvolles Design vereint. Egal ob im Büro oder in der Freizeit, sie ist ein zuverlässiges Accessoire, das Ihnen dabei hilft, die Zeit im Blick zu behalten.

Edifice EQW-M710DB-1A1ER
Benutzerhandbuch (PDF)

Finden Sie die Antwort auf Ihre Frage nicht im Handbuch? Vielleicht finden Sie die Antwort auf Ihre Frage in den FAQs zu Casio Edifice EQW-M710DB-1A1ER unten.

Bei einer Batterie in meinem armbanduhr hat die Korrosion eingesetzt. Ist das Gerät noch sicher zu bedienen?

Das Produkt kann nach ordnungsgemäßer Reinigung weiterhin sicher verwendet werden. Entfernen Sie die Batterie mit Handschuhen und reinigen Sie das Batteriefach mit einer Zahnbürste und Essig. Nach dem Trocknen können neue Batterien in das Gerät eingelegt werden.

Ist das Handbuch der Casio Edifice EQW-M710DB-1A1ER unter Deutsch verfügbar?

Leider haben wir kein Handbuch für Casio Edifice EQW-M710DB-1A1ER in Deutsch verfügbar. Dieses Handbuch ist erhältlich in Englisch.

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Keine Ergebnisse