Name: Casio G-Shock GW-3000M-4AER
Brand: Casio
SKU: 1086391
Rating: 86 (9 reviews)

BedienungsanleitungCasio G-Shock GW-3000M-4AER

Operation Guide 5121

MA1002-EA

Congratulations upon your selection of this CASIO watch.

This watch does not have a city code that corresponds to the UTC offset of –3.5

hours. Because of this, the radio-controlled atomic timekeeping function will not

display the correct time for Newfoundland, Canada.

Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any

damage or loss suffered by you or any third party arising through the use of this

product or its malfunction.

About This Manual

Button operations are indicated using the letters A

through D shown in the illustration.

Hand Functions

z Hour Hand

x Second Hand

c Minute Hand

v Left Dial Hand:

Indicates the current day of the week and current

mode.

b 24-hour Hand:

Indicates the current 24-hour timekeeping hour.

n Right Dial Hands: Indicate a time, in 24-hour format, depending on the current

mode.

m Day

This User’s Guide uses numbers shown above to identify watch hands and indicators.

Things to check before using the watch

1. Hold down C at least two seconds to enter the Timekeeping Mode, and

then observe the movement of the

Second Hand.

Is the

Second Hand moving smoothly at one-second intervals?

Is the

Second Hand moving at

two-second intervals or is it stopped

completely?

Go to step 2.

The watch is charged sufﬁ ciently.

For details about charging, see

“Charging the Watch”.

Power is low. Charge the watch by placing it

in a location where it is exposed to light. For

details, see “Charging the Watch”.

YES

2. Check the Home City and the daylight saving time (DST) setting.

Use the procedure under “To conﬁ gure Home City settings” to conﬁ gure your Home

City and daylight saving time settings.

Important!

Proper time calibration signal reception and World Time settings depend on correct

Home City, time, and date settings in the Timekeeping Mode. Make sure you

conﬁ gure these settings correctly.

3. Set the current time.

• To set the time using a time calibration signal

See “To get ready for a receive operation”.

• To set the time manually

See “Conﬁ guring Current Time and Date Settings Manually”.

The watch is now ready for use.

For details about the watch’s radio contr olled timekeeping feature, see “Radio •

Controlled Atomic Timekeeping”.

Charging the Watch

The face of the watch is a solar cell that generates power from light. The generated

power charges a built-in rechargeable battery, which powers watch operations. The

watch charges whenever it is exposed to light.

Charging Guide

Whenever you are not

wearing the watch, leave

it in a location where it is

exposed to light.

Best charging •

performance is achieved

by exposing the watch to

light that is as strong as

possible.

When wearing the watch,

make sure that its face is

not blocked from light by the

sleeve of your clothing.

The watch may enter a •

sleep state if its face is

blocked by your sleeve

even only partially.

Warning!

Leaving the watch in bright light for charging can cause it to become quite hot.

Take care when handling the watch to avoid burn injury. The watch can become

particularly hot when exposed to the following conditions for long periods.

On the dashboard of a car parked in direct sunlight •

Too close to an incandescent lamp •

Under direct sunlight •

Important!

Keep the watch in an area normally exposed to bright light when storing it for long •

periods. This helps to ensure that power does not run down.

Storing the watch for long periods in an area where there is no light or wearing it in •

such a way that it is blocked from exposure to light can cause power to run down.

Make sure that the watch is exposed to bright light whenever possible.



B +

* 6> 5

Power Levels

You can get an idea of the watch’s power level by

observing the movement of the

Second Hand in the

Timekeeping Mode.

If the •

Second Hand is moving normally at one-second

intervals, power is at Level 1.

If the •

Second Hand is moving at two-second intervals,

power is at Level 2, which is quite low. Expose the watch

to light as soon as possible so it can charge.

Level Hand Movement Function Status

1 Normal. All functions enabled

Second Hand moves at two-second

intervals.

Day changes to 1 (home position).

Beeper, time calibration signal

reception disabled

Second Hand stopped.

z Hour Hand and

Minute Hand

stopped at 12 o’clock.

All functions disabled

When power drops to Level 3, all functions will be disabled but the watch will •

continue to keep time internally for about one week. If you recharge the battery

sufﬁ ciently during this period, the analog hands will move automatically to the

correct setting and regular timekeeping will resume. After one week, all settings

(including timekeeping) will be cleared. Recharging the battery will reset all settings

to their initial factory defaults.

Power Recovery Mode

The watch is designed to go into a power recovery mode that stops hand operation

temporarily whenever power suddenly drops below a certain level due to overuse

of the alarm tone over a short period. Note that all operations are disabled while the

watch is in the power recovery mode.

The hands will move to the correct positions and the watch will resume normal

operation after power recovers (in about 15 minutes). Putting the watch in a location

where it is exposed to light will help power to recover sooner.

Charging Times

Exposure Level (Brightness)

Daily

Operation

Level Change *2

Level 3 Level 2 Level 1

Outdoor sunlight (50,000 lux) 8 minutes 2 hours 24 hours

Window sunlight (10,000 lux) 30 minutes 6 hours 90 hours

Window sunlight on cloudy day

(5,000 lux)

48 minutes 8 hours – – –

Indoor ﬂ uorescent lighting (500 lux) 8 hours 92 hours – – –

1 Approximate exposure each day to generate power for normal daily operation. *

2 Approximate exposure to take power up one level. *

The above times are for reference only. Actual times depend on lighting conditions. •

For details about the operating time and daily operating conditions, see the “Power •

Supply” section of the Speciﬁ cations.

Power Saving

Power Saving enters a sleep state automatically whenever the watch is left for a

certain period in an area where it is dark. The table below shows how watch functions

are affected by Power Saving.

There actually are two sleep state levels: “second hand sleep” and “function sleep”. •

Elapsed Time in Dark Operation

60 to 70 minutes (second hand sleep)

Second Hand only stopped at 12 o’clock, all

other functions enabled

6 or 7 days (function sleep)

All functions, including analog timekeeping, •

disabled

Internal timekeeping maintained •

The watch will not enter a sleep state between 6:00 AM and 9:59 PM. If the watch •

is already in a sleep state when 6:00 AM arrives, however, it will remain in the sleep

state.

The watch will not enter a sleep state while it is in the Stopwatch Mode. •

To recover from the sleep state

Move the watch to a well-lit area or press any button.

Radio Controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly.

However, when using the watch outside of areas covered by time calibration signals,

you will have to adjust the settings manually as required. See “Conﬁ guring Current

Time and Date Settings Manually” for more information.

This section explains how the watch updates its time settings when the city code

selected as the Home City is in Japan, North America, Europe, or China, and is one

that supports time calibration signal reception.

If your Home City code setting is this:

The watch can receive the signal from the

transmitter located here:

LON, PAR, ATH Anthorn (England), Mainﬂ ingen (Germany)

HKG Shangqiu City (China)

TYO Fukushima (Japan), Fukuoka/Saga (Japan)

HNL, ANC, LAX, DEN, CHI, NYC Fort Collins, Colorado (United States)

Important!

The areas covered by • HNL and ANC are quite far from the calibration signal

transmitters, so certain conditions may cause reception problems.

When • HNL or HKG is selected as the Home City, only the time and date are

adjusted according to the time calibration signal. You need to switch manually

between standard time and daylight saving time (DST) if required. See “To toggle

the Home City time between standard time and daylight saving time” for information

about how to do this.

Moves at two-second

intervals.



B +

Bedienungsanleitung

Sehen Sie sich hier kostenlos das Handbuch für Casio G-Shock GW-3000M-4AER an. Dieses Handbuch fällt unter die Kategorie Armbanduhren und wurde von 9 Personen mit einem Durchschnitt von 8.6 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Casio G-Shock GW-3000M-4AER oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Inhaltsangabe

Brauchen Sie Hilfe?

Haben Sie eine Frage zum Casio G-Shock GW-3000M-4AER und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Casio G-Shock GW-3000M-4AER-Besitzer, Ihnen eine gute Antwort zu geben.

Reinold Sandra • 15-1-2021 Keine Kommentare

GW-3000M-4AER Bitte um deutsche Bedienungsanleitung danke

Diese Frage beantworten

Anzahl der Fragen: 1

Casio G-Shock GW-3000M-4AER-Spezifikationen

Nachfolgend finden Sie die Produktspezifikationen und die manuellen Spezifikationen zu Casio G-Shock GW-3000M-4AER.

Allgemeines

Marke	Casio
Model	G-Shock GW-3000M-4AER
Produkte	Armbanduhr
Sprache	Englisch
Dateityp	Benutzerhandbuch (PDF)

Häufig gestellte Fragen

Finden Sie die Antwort auf Ihre Frage nicht im Handbuch? Vielleicht finden Sie die Antwort auf Ihre Frage in den FAQs zu Casio G-Shock GW-3000M-4AER unten.

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Keine Ergebnisse