Casio YK-5

Casio YK-5 Bedienungsanleitung

(1)
  • You can use the YK-5 serial conversion cable to connect the projector to a computer with a commercially available serial cable
    (straight) and control the projector from the computer.
    Be sure to read the user’s guide that comes with the projector and the YK-5 User’s Guide before trying to perform any of the
    operations provided here.
    Keep these instructions in a safe place for future reference.
    The contents of these instructions are subject to change without notice.
    Copying of these instructions, either in part or their entirety, is forbidden. You are allowed to use these instructions for your
    own personal use. Any other use is forbidden without the permission of CASIO COMPUTER CO., LTD.
    CASIO COMPUTER CO., LTD. shall not be held liable for any lost profits or claims from third parties arising out of the use of
    this product or these instructions.
    Connecting the Projector to a Computer
    Connect the projector to the computer as shown in the illustration below.
    * A D-Sub 9-pin (male) type connector is standard for computer serial ports, but there may be cases where the shape of a
    particular computer’s connector is different. For details about connecting a commercially available serial cable to your
    computer, see the user documentation that comes with it.
    Using Control Commands
    This section explains the commands that are used to control the projector from a computer.
    Important!
    Important!
    Important!
    z The commands that will be available to you depend on your projector model. Refer to your projector’s User’s Guide
    for information about the menu items and button functions supported by your projector.
    Example: Some models do not support “Lamp Time Reset”.
    Command Send Format
    See the “Command List” for details about command names and settings.
    All commands use ASCII characters and decimal format integers.
    The projector will return a question mark (?) when it is sent a command it cannot recognize. Also, any command that attempts
    to set a value that is outside the applicable allowable range will be ignored.
    If the projector is performing a process initiated by a previously sent command, a projector key operation, or a remote
    controller key operation, send of the next command must wait until the projector completes the previous process.
    Command List
    Except for the following functions, read and write cannot be performed while the projector is turned off.
    Power on/off: Read
    Power on: Write
    Get lamp time: Read
    Reset lamp time: Write (Only when the lamp reset time exceeds 2100 hours)
    Input of a valid signal must be in progress in order to use a command to turn on blank screen or change the aspect ratio.
    R: Read enabled W: Write enabled
    CASIO DATA PROJECTOR RS-232C Control
    Communication
    Protocol
    Configure your computer’s serial port with the following settings.
    Data Rate 19200bps
    Data Bit 8bit
    Parity None
    Stop Bit 1bit
    Flow Control None
    Read Command Send this command when you want information about the current setup of the data projector.
    Send Format (<command name>?)
    Receive Format (<applicable command setting range>,<current setting>)
    Command Send
    Example
    sent from the computer to the projector.
    4
    returned from the projector to the computer.
    Write Command Send this command to control the data projector (power on/off, etc.) and to write data to it.
    Send Format (<command name><setting value>)
    Command Send
    Example
    sent from the computer to the projector.
    4
    Projector volume setting becomes 0 (mute).
    Projector
    Commercially available serial cable (straight)
    Computer
    Round connector
    Serial port (RS-232C)
    YK-5
    D-Sub 9-pin (female) D-Sub 9-pin (male)
    Serial port*
    D-Sub 9-pin (female)
    (
    VOL ?
    )
    (
    0
    -
    50,35
    )
    (
    VOL 0
    )
    Function
    Command
    Name
    RW Setting Range
    Power On/Off: After turning off a model that requires cool down, you
    must wait until the projector cools down before turning
    power back on again. After power on, wait at least one
    minute before turning power off.
    PWR RW 0: Off, 1: On
    Input Switching: 0: Switches the input source to the COMPUTER
    terminal and changes the COMPUTER terminal
    setting to RGB.
    1: Switches the input source to COMPUTER terminal
    and changes the COMPUTER terminal setting to
    component.
    2: Switches the input source to Video.
    5: Switches the input source to USB. This setting is
    supported only when the projector is equipped with
    a USB function and the USB application is running.
    6: Switches the input source to COMPUTER terminal
    and changes the COMPUTER terminal setting to
    Auto.
    SRC RW 0: RGB, 1: Component,
    2: Video, 5: USB,
    6: Auto (RGB/Component),
    7: HDMI, 8: Wireless
    Blank Screen: Switches the blank screen on or off. BLK RW 0: Off, 1: On
    Volume: Specifies a value to adjust the volume level. This setting is
    applied to the input source signal that is currently being
    projected by the projector.
    VOL RW 0-50
    Color Mode: Selects the color mode. PST RW 0: Presentation, 1: Graphics,
    2: Theater, 3: Standard,
    4: Blackboard
    Aspect Ratio: Specifies the aspect ratio. ARZ RW 0: Maintain, 1: 16:9, 2: 4:3,
    3: Letter Box, 4: Full, 5: True
    Optical Zoom Shift: Shifts the optical zoom setting by one step. OZM W 0: No change,
    1:
    Shifts one step towards wide,
    2: Shifts one step towards tele
    Optical Focus Shift: Shifts the optical focus setting by one step. OFC W 0: No change,
    1:
    Shifts one step towards near,
    2: Shifts one step towards far
    Get Lamp Time: Gets the lamp time from the projector. LMP R 0- Unit: Hours
    Lamp time Reset: Resets the lamp time.
    Lamp time can be reset only when it exceeds 2100 hours and projector
    power is turned off.
    LRT W 0: Do not reset, 1: Reset
    RJA519687-001 Printed in Japan
    MA0912-000000
    B
Casio YK-5

Brauchen Sie Hilfe?

Anzahl der Fragen: 0

Haben Sie eine Frage zum Casio YK-5 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere Casio YK-5-Eigentümer Ihre Frage richtig beantworten.

Sehen Sie sich hier kostenlos das Handbuch für Casio YK-5 an. Dieses Handbuch fällt unter die Kategorie Beamerzubehör und wurde von 1 Personen mit einem Durchschnitt von 8.4 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Casio YK-5 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Casio YK-5-Spezifikationen

Allgemeines
Marke Casio
Model YK-5
Produkte Beamerzubehör
EAN 4971850181934, 0079767181932, 4971850165347
Sprache Englisch
Dateityp PDF
Merkmale
Kompatibilität XJ-A130, XJ-A135U, XJ-A140, XJ-A145V, XJ-A150, XJ-A155V, XJ-A230, XJ-A235U, XJ-A240, XJ-A245V, XJ-A250, XJ-A255V, XJ-S32, XJ-S33, XJ-S37, XJ-S38, XJ-S42, XJ-S43, XJ-S43W, XJ-S47, XJ-S48, XJ-S63, XJ-S68
Produktfarbe Schwarz
Anschlüsse und Schnittstellen
Serielle Schnittstelle RS-232

Bedienungsanleitu.ng

Auf der Suche nach einer Bedienungsanleitung? Bedienungsanleitu.ng sorgt dafür, dass Sie in Windeseile die Bedienungsanleitung finden, die Sie suchen. In unserer Datenbank befinden sich mehr als 1 Million PDF Bedienungsanleitungen von über 10.000 Marken. Jeden Tag fügen wir die neuesten Bedienungsanleitungen hinzu, damit Sie jederzeit das Produkt finden, das Sie suchen. Es ist ganz einfach: Tippen Sie in der Suchleiste Markenname und Produkttyp ein und Sie können direkt die Bedienungsanleitung Ihrer Wahl gratis online einsehen.

Bedienungsanleitu.ng

© Copyright 2020 Bedienungsanleitu.ng. Alle Rechte vorbehalten.

Diese Website benutzen Cookies. Wenn Sie die Website weiter nutzen, stimmen Sie der Verwendung von Cookies zu.

Erfahren Sie mehr