Conair HC18N Bedienungsanleitung
7.5 · 1
BedienungsanleitungConair HC18N
hc18_15pg017942_ib_final.indd 1hc18_15pg017942_ib_final.indd 1 12/17/15 11:01 AM12/17/15 11:01 AM
®
PPERTTAAIILL CCLLII
TRIM
UP
™
C DORDEDED D DEE
Instructions for Clipper Care and Use
Model HC18
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially
when children are present, basic safety pre-
cautions should always be taken, including
the following:
READ ALL INSTRUCTIONS
BEFORE USING
FOR HOUSEHOLD USE ONLY
KEEP AWAY FROM WATER
DANGER
– Any appliance is
electrically live, even when the switch is off.
To reduce the risk of death or injury by
electric shock:
1. Always unplug this appliance from electri-
cal outlet immediately after using.
2. Unplug this appliance before cleaning. Unplug
the appliance when not in use.
3. Do not place or store appliance where it can
fall or be pulled into a tub or sink.
4. Do not use while bathing or in a shower.
5. Do not place in, or drop into water or other
liquids.
6. Do not reach for an appliance that has
fallen into water. Unplug immediately.
WARNING
– To reduce the risk of
burns, electric shock, fire, or injury to persons:
1. This appliance should never be left unattended
when plugged in. Do not pull,
twist, or wrap line
cord around appliance.
2. This appliance should not be used by, on, or near
children or individuals with certain disabilities.
3. Use this appliance only for its intended purpose
as described in this manual. Do not use attach-
ments not recommended by the manufacturer.
Do not use an extension cord to operate this
appliance.
4. Never operate this appliance if it has a damaged
cord or plug, if it is not working properly or if it
has been dropped or damaged, or dropped into
water. Return the appliance to a service center
for examination and repair.
5. Keep the cord away from heated surfaces.
6. Never drop or insert any object into any opening
on this appliance.
7. Do not place appliance on any surface while it
is operating.
8. Do not use this appliance with a damaged or
broken comb or with teeth missing from the
blades as injury may occur. Before use, make
certain blades are aligned properly. (See “Care
of Your Clipper/Trimmer.”)
9. Do not use outdoors or operate where aerosol
(spray) products are being used or where oxy-
gen is being administered.
10. Never operate the appliance with the air open-
ings blocked or while on a soft surface, such
as a bed or couch, where the air openings may
be blocked. Keep the air openings free of lint,
hair, and other debris.
11. Always attach plug to appliance first, then to
outlet. To disconnect, turn all con trols to OFF,
then remove plug from outlet.
12.
Avoid skin contact with moving blades.
13. When using the appliance with its cord,
be mindful of tangles or kinks in the cord.
If the cord does become tangled during
use, turn the unit off, unplug from outlet
and appliance, and straighten cord before
operating again.
THIS PRODUCT IS FOR
HOUSEHOLD USE ONLY
SAVE THESE
INSTRUCTIONS
USER MANUAL
Use on alternating current (120V AC 60HZ) only.
OPERATION
1. For dry location use only. Do not expose to
water.
2. When not in use, unplug unit completely.
3. Unit will become warm during operation.
TROUBLESHOOTING
If your corded trimmer does not seem to be
functioning, take the following troubleshooting
steps before returning it for repair:
1. Be sure the electrical outlet is working by
plugging in another appliance to test the outlet.
2. Make sure the electrical plug is not connected
to a switch that turns power off when lights are
turned off.
OPERATING
INSTRUCTIONS
To reduce the risk of electric shock, this appli-
ance has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized
outlet only one way. If the plug does not fit fully
into the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
Do not attempt to defeat this safety feature.
USER MAINTENANCE
INSTRUCTIONS
OILING THE BLADES
(OIL NOT INCLUDED)
About once a month you should oil the blades.
It is best to do this over a piece of newspaper.
Turn the unit on and hold it so that the blades
are pointed downward. Spread one drop of
lubricating oil across the blades, then turn the
unit off and wipe away the excess oil with a
soft cloth.
Be careful not to use too much oil and don’t oil
more than necessary, as this could damage the
motor. (Never attempt to oil the motor bearing,
as it is permanently lubricated.) After oiling the
blades, return the unit to storage. Keep oil away
from children.
BLADE CARE
Because the blades are precision made for a very
special use, they should always be handled with
care. Each time you finish use, take a cleaning
brush and brush away any loose hair that has col-
lected in the blades. Then store the unit to protect
the blades until the next use.
To promote the long life of the appliance, use
your trimmer only for the purpose intended by
the manufacturer.
THE CONAIR GUIDE
TO CUTTING HAIR AT HOME
Before you start:
1. Inspect your clipper. Make sure it’s free of
hair and dirt, is properly oiled, and running
smoothly.
2. Place a towel around the neck of the person.
3. Seat the person so that his or her head is at
your eye level. This gives you greater visibility
and control.
4. First, comb hair until it’s tangle free. Then
hold clipper in a comfortable grip. Now you’re
ready to cut.
MEDIUM TO LONG CUT
To begin with, cut only a small amount of hair until
you become used to the length each attachment
leaves the hair. Try the longest attachment on the
clipper first. If you want a shorter cut, you can
then use shorter combs.
• Short attachment comb (number AC404)
cuts hair to 1/16" (1.5mm)
• Short-Medium attachment comb
(number AC405) cuts hair to 1/8" (3mm)
• Medium-Long attachment comb
(number AC406) cuts hair to 1/4" (6mm)
• Long attachment comb (number AC407)
cuts hair to 3/8" (9mm)
Attach combs by holding them teeth up, then
snapping onto the bottom of the clipper blade.
To remove comb attachments, place index
finger and thumb on bottom of comb, then pull
out and up.
NOTE: Never push or shove the clipper
through the hair to make it move
more quickly. Professional experience
shows that the clipper works most
efficiently when it cuts through the
hair at its own speed.
TRIMMING
The Trim Up corded clipper can also be
used as a trimming and detailing tool. Great
for touch-ups, trims and fine line detailing
between haircuts.
OUTLINING
Outlining requires no attachments. Comb
hair into the desired style. Position the clip-
per between the sideburns and the ear (see
below), making sure the corner edge of the
blade is against the hairline. With the outline
of the hair as your guide, slowly move the
clipper over, around and behind the ears.
For the back of the neck and the sideburns,
hold the clipper upside down and, holding it
against the skin at the length desired, move
the clipper downward.
STOP. COMB. CHECK.
For best results, do as the professionals do:
Comb hair often, and check clipping results
as you comb. This way you avoid uneven
sides, bangs, neckline, etc.
USE FOR TRIMMING YOUR
BEARD OR MUSTACHE
1. The clipper includes four comb attach-
ments, which provide lengths of 1/16"
(shortest) to 3/8" (longest).
2. To use one of the attachments, press it
down over the blades until it clicks into
position. At first, until you become familiar
with the combs, use the longest comb first.
(You can always go back and make your beard
or mustache a little shorter.)
3. It is always best to begin with a clean,
slightly damp beard/mustache.
4. After you have combed through your beard/
mustache in the direction it grows naturally,
begin trimming using smooth, even strokes.
Start with your sideburns and work down-
ward toward your chin. (Never attempt to trim
against the natural growth of your beard/mus-
tache because the hair will be cut too short.)
5. If you decide you want a closer trim, you
can now switch to the shorter comb (1/16")
and go over your beard/mustache again until
you achieve the desired length.
6. After your beard/mustache has been
trimmed to the desired length, remove the
attachment comb and, using the blades only,
define the outlines of your beard/mustache.
7. Turn off the clipper and remove the attach-
ment by gently pulling up on the tab.
CARE OF YOUR CLIPPER/TRIMMER
REPLACEMENT (REMOVAL) OF BLADE SET
To remove blade set, make sure
the unit is in the OFF position.
Remove the blade set by placing
thumb against the smaller cutter
and pushing forward, releasing
the cutter assembly from the
housing. Replace with new cutting system
and reverse the removal procedure, only this
time place your thumb on the large cutter and
snap into place.
If clipper stops cutting, check to see if there is a
clump of hair lodged between the blades. If that is
the problem, unplug the clipper and then detach
the blade to remove the hair.
If the clipper stops cutting but does not stop
running, you will need to check the blades. For
new blades, send check or money order for
$6.50, which includes postage and handling (if
$10 minimum is met) to:
Conair Corporation
150 Milford Rd.
East Windsor, NJ 08520
NOTE: Never pull on the clipper cord. Never
twist or wrap the cord around the clipper. Lay
it flat with the cord coiled up when not in use.
STORAGE
When not in use, your clipper should be dis-
connected, allowed to cool and stored in a
safe, dry location, out of reach of children.
Any other servicing should be performed by
an authorized service representative. This
appliance has no user-serviceable parts. The
product is for household use.
WARNING:
IF YOU THINK
THE POWER IS OFF
WHEN THE SWITCH
IS OFF,
YOU’RE WRONG.
KEEP AWAY FROM WATER
Everyone knows that electricity and water
are a dangerous combination. But did you
know that an electric appliance is still electri-
cally live even if the switch is off? If the plug
is in, the power is on. So when you are not
using your appliances, keep them unplugged.
ALWAYS UNPLUG
SMALL APPLIANCES
LIMITED TWO-YEAR WARRANTY
(U.S. AND CANADA ONLY)
Conair will repair or replace (at our option) your
unit free of charge for 24 months from the
date of purchase if the appliance is defective in
workmanship or materials.
To obtain service under this warranty, return the
defective product to the service center listed
on back, together with your purchase receipt
and $3.00 for postage and handling. California
residents need only provide proof of purchase
and should call 1-800-3-CONAIR for shipping
instructions. In the absence of a purchase receipt,
the warranty period shall be 24 months from the
date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS,
OR LIABILITIES, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED IN
DURATION TO THE 24-MONTH DURATION OF
THIS WRITTEN, LIMITED WARRANTY. Some
states do not allow limitations on how long an
implied warranty lasts, so the above limitations
may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE
FOR ANY SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES FOR BREACH OF
THIS OR ANY OTHER WARRANTY, EXPRESS
OR IMPLIED, WHATSOEVER. Some states do
not allow the exclusion or limitation of special,
incidental, or consequential damages, so the
above limitation may not apply to you.
This warranty gives you specific legal rights, and
you may also have other rights, which vary from
state to state.
Please register this product at
www.conair.com/registration
Service Center
Conair Corporation
Service Department
7475 North Glen Harbor Blvd.
Glendale, AZ 85307
©2016 Conair Corporation
150 Milford Road, East Windsor, NJ 08520
7475 North Glen Harbor Blvd., Glendale, AZ 85307
15PG017942
IB-14061
CUT HERE
Pricing in effect through December 31, 2018. Orders postmarked after this date will be accepted, and the customer will be notified if pricing has changed.
Attachment Comb 1/16" AC404 $3.00
Attachment Comb 1/8" AC405 $3.00
Attachment Comb 1/4" AC406 $3.00
Attachment Comb 3/8" AC407 $3.00
Lubricating Oil HC-OIL $2.00
T--Blad BLD-166 $6.00
ITEM PART # PRICE QUANTITY AMOUNT
Subtotal
*Sales Tax
TOTAL
Enclose check or money order made payable to Conair. (We cannot accept cash, stamps
or C.O.D. orders.) *CT, IL, AZ, and PA residents should add applicable state sales tax.
Minimum order of $10.00 or a $2.00 handling charge will be added to order.
All prices include handling and return postage. Prices are subject to change
without notice. Prices are valid only for shipments within the continental United States.
Please allow 4–6 weeks for delivery.
To avoid delays, please print clearly.
We must have a street address, as UPS cannot deliver to a P.O. box.
NAME _________________________________________________________________________________________________
ADDRESS ___________________________________________________________________________APT. ______________
CITY __________________________________________________________STATE_______ ZIP ________________________
TELEPHONE ( ) _____________________________________________________________
(We call only if we have a question about your order.)
For information on other Conair® haircut kit parts call: 1-800-3-CONAIR.
Mail to:
Conair Corporation
Service Department
150 Milford Road
East Windsor, NJ 08520-9730
Sehen Sie sich hier kostenlos das Handbuch für Conair HC18N an. Dieses Handbuch fällt unter die Kategorie nicht kategorisiert und wurde von 1 Personen mit einem Durchschnitt von 7.5 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Conair HC18N oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage
Allgemeines
| Conair | |
| HC18N | |
| nicht kategorisiert | |
| Englisch | |
| Benutzerhandbuch (PDF) |
Finden Sie die Antwort auf Ihre Frage nicht im Handbuch? Vielleicht finden Sie die Antwort auf Ihre Frage in den FAQs zu Conair HC18N unten.
Ist das Handbuch der Conair HC18N unter Deutsch verfügbar?
Leider haben wir kein Handbuch für Conair HC18N in Deutsch verfügbar. Dieses Handbuch ist erhältlich in Englisch.
Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage
Keine Ergebnisse
Brauchen Sie Hilfe?
Haben Sie eine Frage zum Conair und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Conair -Besitzer, Ihnen eine gute Antwort zu geben.
Anzahl der Fragen: 0