DeWalt D21002

DeWalt D21002 Bedienungsanleitung

(1)
  • Definitions: Safety Guidelines
    The definitions below describe the level of severity for each
    signal word. Please read the manual and pay attention to these
    symbols.
    DANGER: Indicates an imminently hazardous situation
    which, if not avoided, will result in death or serious injury.
    WARNING: Indicates a potentially hazardous situation which,
    if not avoided, could result in death or serious injury.
    CAUTION: Indicates a potentially hazardous situation which, if
    not avoided, may result in minor or moderate injury.
    CAUTION: Used without the safety alert symbol indicates a
    potentially hazardous situation which, if not avoided, may result
    in property damage.
    IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,
    CALL US TOLL FREE AT: 1-800-4-DEWALT (1-800-433-9258)
    General Safety Rules – For All Tools
    WARNING! Read all instructions. Failure to follow all instructions listed below
    may result in electric shock, fire and/or serious injury. The term “power tool” in all
    of the warnings listed below refers to your mains-operated (corded) power tool or
    battery-operated (cordless) power tool.
    SAVE THESE INSTRUCTIONS
    1) WORK AREA SAFETY
    a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
    b) Do not operate power tools in explosive atmospheres, such as in the presence of
    flammable liquids, gases or dust. Power tools create sparks which may ignite the dust
    or fumes.
    c) Keep children and bystanders away while operating a power tool. Distractions can
    cause you to lose control.
    2) ELECTRICAL SAFETY
    a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
    use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and
    matching outlets will reduce risk of electric shock
    b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
    ranges and refrigerators. There is an increased risk of electric shock if your body is
    earthed or grounded.
    c) Do not expose power tools to rain or wet conditions. Water entering a power tool will
    increase the risk of electric shock
    d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
    power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged
    or entangled cords increase the risk of electric shock. Replace or repair damaged cords.
    Make sure your extension cord is in good condition. Use only 3-wire extension cords that
    have 3-prong grounding-type plugs and 3-pole receptacles that accept the tool’s plug.
    e) When operating a power tool outdoors, use an extension cord suitable for outdoor
    use. Use of a cord suitable for outdoor use reduces the risk of electric shock. When using
    an extension cord, be sure to use one heavy enough to carry the current your product will
    draw. An undersized cord will cause a drop in line voltage resulting in loss of power and
    overheating. The following table shows the correct size to use depending on cord length
    and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the
    gauge number, the heavier the cord.
    Minimum Gauge for Cord Sets
    Ampere Rating
    Volts Total Length of Cord in Feet (meters)
    120V
    25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
    240V
    50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
    More
    Than
    Not More
    Than
    AWG
    0 6 18 16 16 14
    610 18161412
    10 12 16 16 14 12
    12 16 14 12 Not Recommended
    3) PERSONAL SAFETY
    a) Stay alert, watch what you are doing and use common sense when operating a
    power tool. Do not use a power tool while you are tired or under the influence of
    drugs, alcohol or medication. A moment of inattention while operating power toolsmay
    result in serious personal injury.
    b) Use safety equipment. Always wear eye protection. Safety equipment such as
    dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
    conditions will reduce personal injuries.
    c) Avoid accidental starting. Ensure the switch is in the off-position before plugging
    in. Carrying power tools with your finger on the switch or plugging in power tools that have
    the switch on invites accidents.
    d) Remove any adjusting key or wrench before turning the power tool on. A wrench or
    a key left attached to a rotating part of the power tool may result in personal injury.
    e) Do not overreach. Keep proper footing and balance at all times. This enables better
    control of the power tool in unexpected situations.
    f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing
    and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught
    in moving parts. Air vents often cover moving parts and should also be avoided.
    g) If devices are provided for the connection of dust extraction and collection facilities,
    ensure these are connected and properly used. Use of these devices can reduce dust-
    related hazards.
    4) POWER TOOL USE AND CARE
    a) Do not force the power tool. Use the correct power tool for your application. The
    correct power tool will do the job better and safer at the rate for which it was designed.
    b) Do not use the power tool if the switch does not turn it on and off. Any power tool
    that cannot be controlled with the switch is dangerous and must be repaired.
    c) Disconnect the plug from the power source and/or the battery pack from the power
    tool before making any adjustments, changing accessories, or storing power tools.
    Such preventive safety measures reduce the risk of starting the power tool accidentally.
    d) Store idle power tools out of the reach of children and do not allow persons
    unfamiliar with the power tool or these instructions to operate the power tool. Power
    tools are dangerous in the hands of untrained users.
    e) Maintain power tools. Check for misalignment or binding of moving parts, breakage
    of parts and any other condition that may affect the power tool's operation. If
    damaged, have the power tool repaired before use. Many accidents are caused by
    poorly maintained power tools.
    f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
    edges are less likely to bind and are easier to control.
    g) Use the power tool, accessories and tool bits etc., in accordance with these
    instructions and in the manner intended for the particular type of power tool, taking
    into account the working conditions and the work to be performed. Use of the power
    tool for operations different from those intended could result in a hazardous situation.
    5) SERVICE
    a) Have your power tool serviced by a qualified repair person using only identical
    replacement parts. This will ensure that the safety of the power tool is maintained.
    Additional Specific Safety Instructions for Drills
    Hold power tools by insulated gripping surfaces when performing an operation
    where the cutting tool may contact hidden wiring or its own cord. Contact with a “live”
    wire will make exposed metal parts of the tool “live” and shock the operator.
    Use clamps or other practical way to secure and support the workpiece to a stable
    platform. Holding the work by hand or against your body is unstable and may lead to loss
    of control.
    Keep handles dry, clean, free from oil and grease. it is recommended to use rubber
    gloves. This will enable better control of the tool.
    WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.
    Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY
    EQUIPMENT:
    ANSI Z87.1 eye protection (CAN/CSA Z94.3),
    ANSI S12.6 (S3.19) hearing protection,
    NIOSH/OSHA/MSHA respiratory protection.
    WARNING: Always use eye protection. All users and bystanders must wear eye protection
    that conforms to ANSI Z87.1.
    WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
    construction activities contains chemicals known to cause cancer, birth defects, or other
    reproductive harm. Some examples of these chemicals are:
    lead from lead-based paints,
    crystalline silica from bricks and cement and other masonry products, and
    arsenic and chromium from chemically-treated lumber (CCA).
    Your risk from these exposures varies, depending on how often you do this type of work.
    To reduce your exposure to these chemicals: work in a well ventilated area, and work with
    approved safety equipment, such as those dust masks that are specially designed to filter out
    microscopic particles.
    Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and
    other construction activities. Wear protective clothing and wash exposed areas with
    soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote
    absorption of harmful chemicals.
    WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and
    permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
    appropriate for the dust exposure. Direct particles away from face and body.
    The label on your tool may include the following symbols. The symbols and their definitions
    are as follows:
    V ....................volts A ....................amperes
    Hz ..................hertz W ...................watts
    min ................minutes
    .................alternating current
    .............direct current
    n
    o ..................no load speed
    ..................Class I Construction ................... earthing terminal
    (grounded)
    ..................safety alert symbol
    ..................Class II Construction …/min ............revolutions or reciprocation
    (double insulated) per minute
    BPM ..............beats per minute
    SAVE THESE INSTRUCTIONS
    Motor
    Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than
    10% will cause loss of power and overheating. D
    EWALT tools are factory tested; if this tool
    does not operate, check power supply.
    COMPONENTS (FIG. 1, 2, 3)
    WARNING: Never modify the power tool or any part of it. Damage or personal injury could
    result.
    A. Trigger switch
    B. Reversing lever
    C. Bubble level
    D. Bubble level bulls-eye
    E. Keyless chuck
    Keyed chuck (not shown)
    DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
    (AUG07) Form No. 655014-00 D21002, D21007, D21008, D21009, DWD110, DWD112, DWD115
    Copyright © 2002, 2004, 2007 D
    EWALT
    The following are trademarks for one or more DEWALT power tools: the yellow and black
    color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box
    configuration; and the array of lozenge-shaped humps on the surface of the tool.
    INSTRUCTION MANUAL
    GUIDE D'UTILISATION
    MANUAL DE INSTRUCCIÓNES
    D21002, D21007, D21008, D21009, DWD110, DWD112, DWD115
    3/8" (10 mm) V.S.R. Drill
    Perceuse de 10 mm (3/8 po) à régulateur de vitesse et inverseur
    de marche
    Taladro de 10 mm (3/8 pulg.) V.V.R.
    INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO
    Y PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE
    INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
    If you have questions or comments, contact us.
    Pour toute question ou tout commentaire, nous contacter.
    Si tiene dudas o comentarios, contáctenos.
    1-800-4-DEWALT • www.dewalt.com
DeWalt D21002

Brauchen Sie Hilfe?

Anzahl der Fragen: 0

Haben Sie eine Frage zum DeWalt D21002 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere DeWalt D21002-Eigentümer Ihre Frage richtig beantworten.

Sehen Sie sich hier kostenlos das Handbuch für DeWalt D21002 an. Dieses Handbuch fällt unter die Kategorie Bohrmaschinen und wurde von 1 Personen mit einem Durchschnitt von 6 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch, Französisch, Spanisch. Haben Sie eine Frage zum DeWalt D21002 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

DeWalt D21002-Spezifikationen

Allgemeines
Marke DeWalt
Model D21002
Produkte Bohrmaschine
Sprache Englisch, Französisch, Spanisch
Dateityp PDF

Häufig gestellte Fragen

Nachfolgend finden Sie die am häufigsten gestellten Fragen zu DeWalt D21002 .

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Bedienungsanleitu.ng

Auf der Suche nach einer Bedienungsanleitung? Bedienungsanleitu.ng sorgt dafür, dass Sie in Windeseile die Bedienungsanleitung finden, die Sie suchen. In unserer Datenbank befinden sich mehr als 1 Million PDF Bedienungsanleitungen von über 10.000 Marken. Jeden Tag fügen wir die neuesten Bedienungsanleitungen hinzu, damit Sie jederzeit das Produkt finden, das Sie suchen. Es ist ganz einfach: Tippen Sie in der Suchleiste Markenname und Produkttyp ein und Sie können direkt die Bedienungsanleitung Ihrer Wahl gratis online einsehen.

Bedienungsanleitu.ng

© Copyright 2020 Bedienungsanleitu.ng. Alle Rechte vorbehalten.

Diese Website benutzen Cookies. Wenn Sie die Website weiter nutzen, stimmen Sie der Verwendung von Cookies zu.

Erfahren Sie mehr