DeWalt DC750KA

DeWalt DC750KA Bedienungsanleitung

(1)
  • INSTRUCTION MANUAL
    GUIDE D'UTILISATION
    MANUAL DE INSTRUCCIONES
    DC750, DC740, DW907, DW926
    Cordless Adjustable Clutch Driver/Drill
    Perceuse-tournevis sans fil à embrayage réglable
    Taladro/Destornillador Inalámbrico con Embrague Ajustable
    INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
    DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO
    ANTES DE USAR EL PRODUCTO.
    IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,
    CALL US TOLL FREE AT:
    1-800-4-DEWALT (1-800-433-9258)
    General Safety Rules – For All Battery Operated Tools
    WARNING! Read and understand all instructions. Failure to follow all instructions listed
    below may result in electric shock, fire and/or serious personal injury.
    SAVE THESE INSTRUCTIONS
    WORK AREA
    Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
    Do not operate power tools in explosive atmospheres, such as in the presence of flam-
    mable liquids, gases, or dust. Power tools create sparks which may ignite the dust or
    fumes.
    Keep bystanders, children, and visitors away while operating a power tool. Distractions
    can cause you to lose control.
    ELECTRICAL SAFETY
    Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from heat,
    oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords
    may create a fire.
    A battery operated tool with integral batteries or a separate battery pack must be
    recharged only with the specified charger for the battery. A charger that may be suitable
    for one type of battery may create a risk of fire when used with another battery.
    Use battery operated tool only with the specifically designated battery pack. Use of any
    other batteries may create a risk of fire.
    PERSONAL SAFETY
    Stay alert, watch what you are doing and use common sense when operating a power
    tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A
    moment of inattention while operating power tools may result in serious personal injury,
    Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair,
    clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be
    caught in moving parts.
    Air vents often cover moving parts and should also be avoided.
    Avoid accidental starting. Be sure switch is in the locked or off position before inserting bat-
    tery pack. Carrying tools with your finger on the switch or inserting the battery pack into a tool
    with the switch on invites accidents.
    Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that
    is left attached to a rotating part of the tool may result in personal injury.
    Do not overreach. Keep proper footing and balance at all times. Proper footing and balance
    enables better control of the tool in unexpected situations.
    Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,
    hard hat, or hearing protection must be used for appropriate conditions.
    TOOL USE AND CARE
    Use clamps or other practical way to secure and support the workpiece to a stable
    platform. Holding the work by hand or against your body is unstable and may lead to a loss
    of control.
    Do not force tool. Use the correct tool for your application. The correct tool will do the
    job better and safer at the rate for which it is designed.
    Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with
    the switch is dangerous and must be repaired.
    Disconnect battery pack from tool or place the switch in the locked or off position
    before making any adjustments, changing accessories, or storing the tool. Such pre-
    ventative safety measures reduce the risk of starting the tool accidentally.
    Store idle tools out of reach of children and other untrained persons. Tools are dan-
    gerous in the hands of untrained users.
    When battery pack is not in use, keep it away from other metal objects like: paper
    clips, coins, keys, nails, screws, or other small metal objects that can make a con-
    nection from one terminal to another. Shorting the battery terminals together may cause
    sparks, burns, or a fire.
    Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,
    with sharp cutting edges are less likely to bind and are easier to control.
    Check for misalignment or binding of moving parts, breakage of parts, and any other
    condition that may affect the tools operation. If damaged, have the tool serviced before
    using. Many accidents are caused by poorly maintained tools.
    Use only accessories that are recommended by the manufacturer for your model.
    Accessories that may be suitable for one tool, may create a risk of injury when used on
    another tool.
    SERVICE
    Tool service must be performed only by qualified repair personnel. Service or mainte-
    nance performed by unqualified personnel result in a risk of injury.
    When servicing a tool, use only identical replacement parts. Follow instructions in the
    Maintenance section of this manual. Use of unauthorized parts or failure to follow
    Maintenance Instructions may create a risk of shock or injury.
    Additional Safety Rules
    Hold tool by insulated gripping surfaces when performing an operation where the tool
    may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts of
    the tool “live” and shock the operator.
    WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.
    Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY
    EQUIPMENT:
    ANSI Z87.1 eye protection (CAN/CSA Z94.3)
    ANSI S12.6 (S3.19) hearing protection
    NIOSH/OSHA/MSHA respiratory protection.
    WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
    construction activities contains chemicals known to cause cancer, birth defects or other
    reproductive harm. Some examples of these chemicals are:
    lead from lead-based paints,
    crystalline silica from bricks and cement and other masonry products, and
    arsenic and chromium from chemically-treated lumber (CCA).
    Your risk from these exposures varies, depending on how often you do this type of work. To
    reduce your exposure to these chemicals: work in a well ventilated area, and work with
    approved safety equipment, such as those dust masks that are specially designed to filter out
    microscopic particles.
    Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
    and other construction activities. Wear protective clothing and wash exposed areas
    with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may
    promote absorption of harmful chemicals.
    WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and
    permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
    appropriate for the dust exposure. Direct particles away from face and body.
    CAUTION: Wear appropriate personal hearing protection during use. Under some con-
    ditions and duration of use, noise from this product may contribute to hearing loss.
    CAUTION: When not in use, place tool on its side on a stable surface where it will not
    cause a tripping or falling hazard. Some tools with large battery packs will stand upright on
    the battery pack but may be easily knocked over.
    The label on your tool may include the following symbols. The symbols and their definitions
    are as follows:
    V..................volts A ....................amperes
    Hz................hertz W ....................watts
    min ..............minutes ..................alternating current
    ............direct current
    n
    o....................no load speed
    ................Class I Construction ....................earthing terminal
    ....................(grounded) ....................safety alert symbol
    ................Class II Construction .../min..............revolutions per minute
    ....................(double insulated) BPM................beats per minute
    SAVE THESE INSTRUCTIONS
    Important Safety Instructions for Battery Packs
    Your tool uses either a 12, 14.4 or 18 Volt DEWALT battery pack. When ordering replacement
    battery packs, be sure to include catalog number and voltage: Extended Run-Time battery packs
    deliver 25% more run-time than standard battery packs.
    NOTE: Your tool will accept either standard or Extended Run Time battery packs. However, be
    sure to select proper voltage.
    The battery pack is not fully charged out of the carton. Before using the battery pack and
    charger, read the safety instructions below. Then follow charging procedures outlined.
    READ ALL INSTRUCTIONS
    Do not incinerate the battery pack even if it is severely damaged or is completely worn
    out. The battery pack can explode in a fire.
    A small leakage of liquid from the battery pack cells may occur under extreme usage
    or temperature conditions. This does not indicate a failure. However, if the outer seal is
    broken and this leakage gets on your skin:
    a. Wash quickly with soap and water.
    b. Neutralize with a mild acid such as lemon juice or vinegar.
    c. If battery liquid gets into your eyes, flush them with clean water for a minimum of 10 min-
    utes and seek immediate medical attention. (Medical note: The liquid is 25-35% solution
    of potassium hydroxide.)
    Do not carry extra battery packs in aprons, pockets, or tool boxes along with other
    metal objects. Battery pack could be short circuited causing damage to the battery pack and
    possibly causing severe burns or fire.
    Charge the battery packs only in D
    E
    WALT chargers.
    DO NOT splash or immerse in water or other liquids.
    Do not store or use the tool and battery pack in locations where the temperature may
    reach or exceed 105°F (such as outside sheds or metal buildings in summer).
    DANGER: Electrocution hazard. Never attempt to open the battery pack for any reason. If
    battery pack case is cracked or damaged, do not insert into charger. Electric shock or electro-
    cution may result. Damaged battery packs should be returned to service center for recycling.
    NOTE: Battery storage and carrying caps are provided for use whenever the battery
    is out of the tool or charger. Remove cap before placing battery in charger or tool.
    WARNING: Fire hazard. Do not store or carry battery so that metal objects
    can contact exposed battery terminals. For example, do not place battery in
    aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails,
    screws, keys, etc. without battery cap. Transporting batteries can possibly
    cause fires if the battery terminals inadvertently come in contact with conductive materi-
    als such as keys, coins, hand tools and the like. The US Department of Transportation
    Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce
    or on airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they are properly pro-
    tected from short circuits. So when transporting individual batteries, make sure that the battery
    terminals are protected and well insulated from materials that could contact them and cause a
    short circuit.
    CAUTION: Battery pack must be securely attached to tool. If battery pack is detached, per-
    sonal injury may result.
    The RBRC™ Seal
    The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the
    nickel cadmium and nickel metal hydride batteries (or battery packs) indicate that
    the costs to recycle these batteries (or battery packs) at the end of their useful
    life have already been paid by D
    EWALT. In some areas, it is illegal to place spent
    nickel cadmium and nickel metal hydride batteries in the trash or municipal solid
    waste stream and the RBRC program provides an environmentally conscious
    alternative.
    RBRC™ in cooperation with D
    EWALT and other battery users, has established programs in the
    United States and Canada to facilitate the collection of spent nickel cadmium and nickel metal
    hydride batteries. Help protect our environment and conserve natural resources by returning
    the spent nickel cadmium and nickel metal hydride batteries to an authorized D
    EWALT service
    center or to your local retailer for recycling. You may also contact your local recycling center for
    information on where to drop off the spent battery.
    RBRC™ is a registered trademark of the
    Rechargeable Battery Recycling Corporation.
    Important Safety Instructions for Battery Chargers
    SAVE THESE INSTRUCTIONS: This manual contains important safety instructions for battery
    chargers.
    Before using charger, read all instructions and cautionary markings on charger, battery pack,
    and product using battery pack.
    DANGER: Electrocution hazard. 120 volts are present at charging terminals. Do not probe with
    conductive objects. Electric shock or electrocution may result.
    WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may
    result.
    CAUTION: Burn hazard. To reduce the risk of injury, charge only D
    E
    WALT nickel cadmium
    rechargeable batteries. Other types of batteries may burst causing personal injury and damage.
    CAUTION: Under certain conditions, with the charger plugged in to the power supply,
    the exposed charging contacts inside the charger can be shorted by foreign material. Foreign
    materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any
    buildup of metallic particles should be kept away from charger cavities. Always unplug the
    charger from the power supply when there is no battery pack in the cavity. Unplug charger before
    attempting to clean.
    DO NOT attempt to charge the battery pack with any chargers other than the ones in
    this manual. The charger and battery pack are specifically designed to work together.
    These chargers are not intended for any uses other than charging D
    E
    WALT recharge-
    able batteries. Any other uses may result in risk of fire, electric shock or electrocution.
    Do not expose charger to rain or snow.
    Pull by plug rather than cord when disconnecting charger. This will reduce risk of
    damage to electric plug and cord.
    Make sure that cord is located so that it will not be stepped on, tripped over, or other-
    wise subjected to damage or stress.
    Do not use an extension cord unless it is absolutely necessary. Use of improper
    extension cord could result in risk of fire, electric shock, or electrocution.
    An extension cord must have adequate wire size (AWG or American Wire Gauge) for
    safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that
    is 16 gauge has more capacity than 18 gauge. When using more than one extension to make
    up the total length, be sure each individual extension contains at least the minimum wire size.
    Do not place any object on top of charger or place the charger on a soft surface that
    might block the ventilation slots and result in excessive internal heat. Place the charg-
    er in a position away from any heat source. The charger is ventilated through slots in the top
    and the bottom of the housing.
    Do not operate charger with damaged cord or plug — have them replaced immediately.
    DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
    (SEP06) Form No. 646257-00 DC750, DC740, DW907, DW926
    Copyright © 1999, 2003, 2004, 2006 DEWALT
    The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the
    “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of
    lozenge-shaped humps on the surface of the tool.
    If you have questions or comments, contact us.
    Pour toute question ou tout commentaire, nous contacter.
    Si tiene dudas o comentarios, contáctenos.
    1-800-4-DEWALT • www.dewalt.com
DeWalt DC750KA

Brauchen Sie Hilfe?

Anzahl der Fragen: 0

Haben Sie eine Frage zum DeWalt DC750KA oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere DeWalt DC750KA-Eigentümer Ihre Frage richtig beantworten.

Sehen Sie sich hier kostenlos das Handbuch für DeWalt DC750KA an. Dieses Handbuch fällt unter die Kategorie Bohrmaschinen und wurde von 1 Personen mit einem Durchschnitt von 6.4 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch, Französisch, Spanisch. Haben Sie eine Frage zum DeWalt DC750KA oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

DeWalt DC750KA-Spezifikationen

Allgemeines
Marke DeWalt
Model DC750KA
Produkte Bohrmaschine
Sprache Englisch, Französisch, Spanisch
Dateityp PDF

Häufig gestellte Fragen

Nachfolgend finden Sie die am häufigsten gestellten Fragen zu DeWalt DC750KA .

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Bedienungsanleitu.ng

Auf der Suche nach einer Bedienungsanleitung? Bedienungsanleitu.ng sorgt dafür, dass Sie in Windeseile die Bedienungsanleitung finden, die Sie suchen. In unserer Datenbank befinden sich mehr als 1 Million PDF Bedienungsanleitungen von über 10.000 Marken. Jeden Tag fügen wir die neuesten Bedienungsanleitungen hinzu, damit Sie jederzeit das Produkt finden, das Sie suchen. Es ist ganz einfach: Tippen Sie in der Suchleiste Markenname und Produkttyp ein und Sie können direkt die Bedienungsanleitung Ihrer Wahl gratis online einsehen.

Bedienungsanleitu.ng

© Copyright 2020 Bedienungsanleitu.ng. Alle Rechte vorbehalten.

Diese Website benutzen Cookies. Wenn Sie die Website weiter nutzen, stimmen Sie der Verwendung von Cookies zu.

Erfahren Sie mehr