DeWalt DCD910KX

DeWalt DCD910KX Bedienungsanleitung

(1)
  • INSTRUCTION MANUAL
    GUIDE D’UTILISATION
    MANUAL DE INSTRUCCIONES
    INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA
    DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES
    DE USAR EL PRODUCTO.
    DEWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD 21286
    (OCT08) Part No. 658870-00 DCD910, etc. Copyright © 2008 D
    EWALT
    The following are trademarks for one or more D
    EWALT power tools: the yellow and black color scheme;
    the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the
    array of lozenge-shaped humps on the surface of the tool.
    DCD910, DCD920, DCD940, DCD960 Heavy-Duty 1/2" (13 mm) Cordless Drill/Driver
    DCD930, DCD950, DCD970 Heavy-Duty 1/2" (13 mm) Cordless Hammerdrill/Drill/Drivers
    Perceuses/Visseuses industrielles sans fil 13 mm (1/2 po) DCD910, DCD920, DCD940, DCD960
    Marteaux perforateurs/Perceuses/Visseuses industriels sans fil 13 mm (1/2 po) DCD930, DCD950, DCD970
    Taladro / destornillador inalámbrico de 1/2 pulg. (13 mm) para trabajos pesados DCD910, DCD920, DCD940, DCD960
    Taladro percusor / taladro / destornillador inalámbrico de 1/2 pulg. (13 mm) para trabajos pesados DCD930, DCD950, DCD970
    If you have questions or comments, contact us.
    Pour toute question ou tout commentaire, nous contacter.
    Si tiene dudas o comentarios, contáctenos.
    1-800-4-DEWALT • www.dewalt.com
    Definitions: Safety Guidelines
    The definitions below describe the level of severity for each signal word. Please read
    the manual and pay attention to these symbols.
    DANGER: Indicates an imminently hazardous situation which, if not avoided, will
    result in death or serious injury.
    WARNING: Indicates a potentially hazardous situation which, if not avoided, could
    result in death or serious injury.
    CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
    result in minor or moderate injury.
    CAUTION: Used without the safety alert symbol indicates a potentially hazardous
    situation which, if not avoided, may result in property damage.
    IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,
    CALL US TOLL FREE AT: 1-800-4-D
    EWALT (1-800-433-9258).
    WARNING: To reduce the risk of injury, read the instruction manual.
    General Power Tool Safety Warnings
    WARNING! Read all safety warnings and all instructions. Failure to follow the warnings
    and instructions may result in electric shock, fire and/or serious injury.
    SAVE ALL WARNINGS AND INSTRUCTIONS
    FOR FUTURE REFERENCE
    The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
    battery-operated (cordless) power tool.
    1) WORK AREA SAFETY
    a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
    b) Do not operate power tools in explosive atmospheres, such as in the presence of
    flammable liquids, gases or dust. Power tools create sparks which may ignite the dust
    or fumes.
    c) Keep children and bystanders away while operating a power tool. Distractions can
    cause you to lose control.
    2) ELECTRICAL SAFETY
    a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not
    use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and
    matching outlets will reduce risk of electric shock.
    b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
    ranges and refrigerators. There is an increased risk of electric shock if your body is
    earthed or grounded.
    c) Do not expose power tools to rain or wet conditions. Water entering a power tool will
    increase the risk of electric shock.
    d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
    power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged
    or entangled cords increase the risk of electric shock.
    e) When operating a power tool outdoors, use an extension cord suitable for outdoor
    use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
    f) If operating a power tool in a damp location is unavoidable, use a ground fault
    circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric
    shock.
    3) PERSONAL SAFETY
    a) Stay alert, watch what you are doing and use common sense when operating a
    power tool. Do not use a power tool while you are tired or under the influence of
    drugs, alcohol or medication. A moment of inattention while operating power tools may
    result in serious personal injury.
    b) Use personal protective equipment. Always wear eye protection. Protective equipment
    such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for
    appropriate conditions will reduce personal injuries.
    c) Prevent unintentional starting. Ensure the switch is in the off position before
    connecting to power source and/or battery pack, picking up or carrying the tool.
    Carrying power tools with your finger on the switch or energising power tools that have the
    switch on invites accidents.
    d) Remove any adjusting key or wrench before turning the power tool on. A wrench or
    a key left attached to a rotating part of the power tool may result in personal injury.
    e) Do not overreach. Keep proper footing and balance at all times. This enables better
    control of the power tool in unexpected situations.
    f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and
    gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in
    moving parts.
    g) If devices are provided for the connection of dust extraction and collection facilities,
    ensure these are connected and properly used. Use of dust collection can reduce dust-
    related hazards.
    4) POWER TOOL USE AND CARE
    a) Do not force the power tool. Use the correct power tool for your application. The
    correct power tool will do the job better and safer at the rate for which it was designed.
    b) Do not use the power tool if the switch does not turn it on and off. Any power tool that
    cannot be controlled with the switch is dangerous and must be repaired.
    c) Disconnect the plug from the power source and/or the battery pack from the power
    tool before making any adjustments, changing accessories, or storing power tools.
    Such preventive safety measures reduce the risk of starting the power tool accidentally.
    d) Store idle power tools out of the reach of children and do not allow persons
    unfamiliar with the power tool or these instructions to operate the power tool. Power
    tools are dangerous in the hands of untrained users.
    e) Maintain power tools. Check for misalignment or binding of moving parts, breakage
    of parts and any other condition that may affect the power tool’s operation. If
    damaged, have the power tool repaired before use. Many accidents are caused by
    poorly maintained power tools.
    f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
    edges are less likely to bind and are easier to control.
    g) Use the power tool, accessories and tool bits, etc. in accordance with these
    instructions, taking into account the working conditions and the work to be
    performed. Use of the power tool for operations different from those intended could
    result in a hazardous situation.
    5) BATTERY TOOL USE AND CARE
    a) Recharge only with the charger specified by the manufacturer. A charger that is
    suitable for one type of battery pack may create a risk of fire when used with another
    battery pack.
    b) Use power tools only with specifically designated battery packs. Use of any other
    battery packs may create a risk of injury and fire.
    c) When battery pack is not in use, keep it away from other metal objects like paper
    clips, coins, keys, nails, screws, or other small metal objects that can make a
    connection from one terminal to another. Shorting the battery terminals together may
    cause burns or a fire.
    d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
    contact accidentally occurs, flush with water. If liquid contacts eyes, additionally
    seek medical help. Liquid ejected from the battery may cause irritation or burns.
    6) SERVICE
    a) Have your power tool serviced by a qualified repair person using only identical
    replacement parts.
    This will ensure that the safety of the power tool is maintained.
    Specific Safety Rules
    Wear ear protectors with impact drills. Exposure to noise can cause hearing loss.
    Use auxiliary handles supplied with the tool. Loss of control can cause personal injury.
    Hold power tools by insulated gripping surfaces when performing an operation
    where the cutting tool may contact hidden wiring or its own cord. Contact with a “live”
    wire will make exposed metal parts of the tool “live” and shock the operator.
    Use clamps or another practical way to secure and support the workpiece to a stable
    platform. Holding the work by hand or against your body leaves it unstable and may lead to
    loss of control.
    Wear ear protectors when hammering for extented periods of time. Prolonged exposure
    to high intensity noise can cause hearing loss. Temporary hearing loss or serious ear drum
    damage may result from high sound levels generated by hammer drilling.
    Wear safety goggles or other eye protection. Hammering and drilling operations cause
    chips to fly. Flying particles can cause permanent eye damage.Wear a dust mask or respirator
    for applications that generate dust. Ear protection may be required for most applications.
    Always use the side handle supplied with the tool. Keep a firm grip on the tool at all
    times. Do not attempt to operate this tool without holding it with both hands. Operating
    this tool with one hand will result in loss of control. Breaking through or encountering hard
    materials such as re-bar may be hazardous as well.
    Accessories and tool may get hot during operation. Wear gloves when handling them if
    performing heat producing applications such as hammerdrilling and drilling metals.
    Do not operate this tool for long periods of time. Vibration caused by hammer action may
    be harmful to your hands and arms. Use gloves to provide extra cushion and limit exposure
    by taking frequent rest periods.
    Air vents often cover moving parts and should be avoided. Loose clothes, jewellery or
    long hair can be caught in moving parts.
    WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also
    use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY
    EQUIPMENT:
    ANSI Z87.1 eye protection (CAN/CSA Z94.3),
    ANSI S12.6 (S3.19) hearing protection,
    NIOSH/OSHA/MSHA respiratory protection.
    WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
    construction activities contains chemicals known to cause cancer, birth defects or other
    reproductive harm. Some examples of these chemicals are:
    lead from lead-based paints,
    crystalline silica from bricks and cement and other masonry products, and
    arsenic and chromium from chemically-treated lumber (CCA).
    Your risk from these exposures varies, depending on how often you do this type of work. To
    reduce your exposure to these chemicals: work in a well ventilated area, and work with approved
    safety equipment, such as those dust masks that are specially designed to filter out microscopic
    particles.
    Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and
    other construction activities. Wear protective clothing and wash exposed areas with
    soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote
    absorption of harmful chemicals.
    WARNING: Use of this tool can generate and/or disburse dust, which may cause serious and
    permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
    appropriate for the dust exposure. Direct particles away from face and body.
    WARNING: Always wear proper personal hearing protection that conforms to ANSI
    S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this product
    may contribute to hearing loss.
    CAUTION: When not in use, place tool on its side on a stable surface where it will not
    cause a tripping or falling hazard. Some tools with large battery packs will stand upright on
    the battery pack but may be easily knocked over.
    The label on your tool may include the following symbols. The symbols and their definitions
    are as follows:
    V ......................volts A ......................amperes
    Hz ....................hertz W .....................watts
    min ..................minutes
    ................... alternating current
    ...............direct current ...................alternating or direct current
    ....................Class I Construction
    n
    o ....................no load speed
    ........................(grounded) ....................earthing terminal
    ....................Class II Construction ....................safety alert symbol
    ........................(double insulated) BPM ................beats per minute
    …/min .............per minute RPM ................revolutions per minute
    IPM..................impacts per minute
    Important Safety Instructions for All Battery Packs
    When ordering replacement battery packs, be sure to include catalog number and voltage.
    Consult the chart at the end of this manual for compatibility of chargers and battery packs.
    The battery pack is not fully charged out of the carton. Before using the battery pack and
    charger, read the safety instructions below. Then follow charging procedures outlined.
    READ ALL INSTRUCTIONS
    Do not charge or use battery in explosive atmospheres, such as in the presence of
    flammable liquids, gases or dust. Inserting or removing the battery from the charger may
    ignite the dust or fumes.
    • NEVER force battery pack into charger. DO NOT modify battery pack in any way
    to fit into a non-compatible charger as battery pack may rupture causing serious
    personal injury. Consult the chart at the end of this manual for compatibility of batteries and
    chargers.
    Charge the battery packs only in D
    EWALT chargers.
    DO NOT splash or immerse in water or other liquids.
    Do not store or use the tool and battery pack in locations where the temperature may
    reach or exceed 105°F (40˚C) (such as outside sheds or metal buildings in summer).
    DANGER: Electrocution hazard. Never attempt to open the battery pack for any reason.
    If battery pack case is cracked or damaged, do not insert into charger. Do not crush, drop or
    damage battery pack. Do not use a battery pack or charger that has received a sharp blow,
    been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer,
    stepped on). Electric shock or electrocution may result. Damaged battery packs should be
    returned to service center for recycling.
    NOTE: Battery storage and carrying caps are provided for use whenever the
    battery is out of the tool or charger. Remove cap before placing battery in charger
    or tool.
    WARNING: Fire hazard. Do not store or carry battery so that metal
    objects can contact exposed battery terminals. For example, do not place
    battery in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws,
    keys, etc. without battery cap. Transporting batteries can possibly cause fires if the battery
    terminals inadvertently come in contact with conductive materials such as keys, coins,
    hand tools and the like. The US Department of Transportation Hazardous Material Regulations
    (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e., packed in
    suitcases and carry-on luggage) UNLESS they are properly protected from short circuits. So
    when transporting individual batteries, make sure that the battery terminals are protected and
    well insulated from materials that could contact them and cause a short circuit.
    SPECIFIC SAFETY INSTRUCTIONS FOR NICKEL CADMIUM (NiCd) OR NICKEL METAL
    HYDRIDE (NiMH)
    Do not incinerate the battery pack even if it is severely damaged or is completely worn
    out. The battery pack can explode in a fire.
    A small leakage of liquid from the battery pack cells may occur under extreme usage
    or temperature conditions. This does not indicate a failure.
    However, if the outer seal is broken:
    a. and the battery liquid gets on your skin, immediately wash with soap and water for several
    minutes.
    b. and the battery liquid gets into your eyes, flush them with clean water for a minimum of
    10 minutes and seek immediate medical attention. (Medical note: The liquid is 25-35%
    solution of potassium hydroxide.)
    SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (LI-ION)
    Do not incinerate the battery pack even if it is severely damaged or is completely
    worn out. The battery pack can explode in a fire. Toxic fumes and materials are created
    when lithium ion battery packs are burned.
    If battery contents come into contact with the skin, immediately wash area with
    mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for
    15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is
    composed of a mixture of liquid organic carbonates and lithium salts.
    Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If
    symptoms persists, seek medical attention.
    WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.
    The RBRC™ Seal
    The RBRC™ (Rechargeable Battery Recycling Corp oration) Seal on the nickel
    cadmium, nickel metal hydride or lithium ion batteries (or battery packs) indicate
    that the costs to recycle these batteries (or battery packs) at the end of their useful
    life have already been paid by D
    EWALT. In some areas, it is illegal to place spent
    nickel cadmium, nickel metal hydride or lithium ion batteries in the trash or municipal solid waste
    stream and the RBRC program provides an environmentally conscious alternative.
    RBRC™ in cooperation with D
    EWALT and other battery users, has established programs in
    the United States and Canada to facilitate the collection of spent nickel cadmium, nickel metal
    hydride or lithium ion batteries. Help protect our environment and conserve natural resources
    by returning the spent nickel cadmium and nickel cadmium, nickel metal hydride or lithium ion
    batteries to an authorized D
    EWALT service center or to your local retailer for recycling. You may
    also contact your local recycling center for information on where to drop off the spent battery.
    RBRC™ is a registered trademark of the Rechargeable Battery Recycling Corporation.
    Important Safety Instructions for All Battery Chargers
    SAVE THESE INSTRUCTIONS: This manual contains important safety and operating instructions
    for battery chargers.
    Before using charger, read all instructions and cautionary markings on charger, battery pack,
    and product using battery pack.
    DANGER: Electrocution hazard. 120 volts are present at charging terminals. Do not probe
    with conductive objects. Electric shock or electrocution may result.
    WARNING: Shock hazard. Do not allow any liquid to get inside charger. Electric shock may
    result.
    CAUTION: Burn hazard. To reduce the risk of injury, charge only DEWALT rechargeable
    batteries. Other types of batteries may burst causing personal injury and damage.
    CAUTION: Under certain conditions, with the charger plugged in to the power supply, the
    exposed charging contacts inside the charger can be shorted by foreign material. Foreign
    materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any
    buildup of metallic particles should be kept away from charger cavities. Always unplug the
    charger from the power supply when there is no battery pack in the cavity. Unplug charger
    before attempting to clean.
    DO NOT attempt to charge the battery pack with any chargers other than the ones in
    this manual. The charger and batter y pack are specifically designed to work together.
    These chargers are not intended for any uses other than charging D
    EWALT rechargeable
    batteries. Any other uses may result in risk of fire, electric shock or electrocution.
    Do not expose charger to rain or snow.
    Pull by plug rather than cord when disconnecting charger. This will reduce risk of
    damage to electric plug and cord.
    Make sure that cord is located so that it will not be stepped on, tripped over, or
    otherwise subjected to damage or stress.
    Do not use an extension cord unless it is absolutely necessary. Use of improper
    extension cord could result in risk of fire, electric shock, or electrocution.
    When operating a power tool outdoors, use an extension cord suitable for outdoor
    use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
    An extension cord must have adequate wire size (AWG or American Wire Gauge) for
    safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that
    is 16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line
    voltage resulting in loss of power and overheating. When using more than one extension to
DeWalt DCD910KX

Brauchen Sie Hilfe?

Anzahl der Fragen: 0

Haben Sie eine Frage zum DeWalt DCD910KX oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere DeWalt DCD910KX-Eigentümer Ihre Frage richtig beantworten.

Sehen Sie sich hier kostenlos das Handbuch für DeWalt DCD910KX an. Dieses Handbuch fällt unter die Kategorie Bohrmaschinen und wurde von 1 Personen mit einem Durchschnitt von 7.1 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch, Französisch, Spanisch. Haben Sie eine Frage zum DeWalt DCD910KX oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

DeWalt DCD910KX-Spezifikationen

Allgemeines
Marke DeWalt
Model DCD910KX
Produkte Bohrmaschine
Sprache Englisch, Französisch, Spanisch
Dateityp PDF

Häufig gestellte Fragen

Nachfolgend finden Sie die am häufigsten gestellten Fragen zu DeWalt DCD910KX .

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Bedienungsanleitu.ng

Auf der Suche nach einer Bedienungsanleitung? Bedienungsanleitu.ng sorgt dafür, dass Sie in Windeseile die Bedienungsanleitung finden, die Sie suchen. In unserer Datenbank befinden sich mehr als 1 Million PDF Bedienungsanleitungen von über 10.000 Marken. Jeden Tag fügen wir die neuesten Bedienungsanleitungen hinzu, damit Sie jederzeit das Produkt finden, das Sie suchen. Es ist ganz einfach: Tippen Sie in der Suchleiste Markenname und Produkttyp ein und Sie können direkt die Bedienungsanleitung Ihrer Wahl gratis online einsehen.

Bedienungsanleitu.ng

© Copyright 2020 Bedienungsanleitu.ng. Alle Rechte vorbehalten.

Diese Website benutzen Cookies. Wenn Sie die Website weiter nutzen, stimmen Sie der Verwendung von Cookies zu.

Erfahren Sie mehr