Name: First Alert ADF-12
Brand: First Alert
SKU: 1544954
Rating: 75 (1 reviews)

BedienungsanleitungFirst Alert ADF-12

INSTALLATION OF THE

ADF ADAPTER PLUG

ELECTRICAL SHOCK HAZARD. T

urn off power to the area where you

will install this unit at the cir

cuit breaker or fuse box before beginning

installation. Failure to turn off the power before installation may result in

serious electrical shock, injury or death. Do not restore power until all

Smoke Alar

ms are completely installed.

•

Installation of this unit must conform to the electrical codes in your

ea; Article 760 of NFPA 70 (NEC), NFPA 72, NFPA 101; SBC (SBCCI);

UBC (ICBO); NBC (BOCA); OTFDC (CABO), and any other local or

building codes that may apply. Wiring and installation must be per-

formed by a licensed electrician. Failure to follow these guidelines

may r

esult in injury or property damage.

•

This unit must be powered by a 24-hour, 120VAC

pure sine wave

60Hz

cir

cuit. Be sure the circuit cannot be turned off by a switch, dimmer,

or gr

ound fault circuit interrupter. Failure to connect this unit to a

24-hour circuit may prevent it from providing constant protection.

For all other Smoke Alarm information, instructions and warnings, refer

to the Smoke Alarm User’s Manual.

Independent evaluation of the

Adapter Plug and inter

connect

compatibility was performed by

Intertek, a division of ETL SEMKO.

3901 Liberty Street Road, Aurora, IL 60504-8122

Consumer Af

fairs: (800) 323-9005 • www

.firstalert.com • www

.brkelectronics.com

US Patent No.: 6,641,433 B2

BRK

is a registered trademark of BRK Brands, Inc.

First Alert

is a registered trademark of the First Alert Trust.

Firex

is a registered trademark of Maple Chase Company.

Printed in Mexico M08-0125-001 H 06/07

INCOMP

TIBLE POWER CONNECTORS:

FIREX

DO NOT A

TTEMPT

INSTALLATION

INSTALLATION INSTRUCTIONS

1. V

erify which

MODELS ar

e installed in your system to determine if they are

compatible with the ADF Adapter Plug (see part C below).

2. T

urn off AC power.

3. Remove unit. Remove old mounting bracket.

4. Install new mounting bracket (see part A below).

5. Connect the black end of the ADF Adapter Plug to the existing power

connector (connect part C to part D as shown below).

NOTE: There may not be enough room for the Adapter Plug and additional

wiring to fit in the junction box. If not, the old power connector must be

emoved and r

eplaced with a First Alert

Power Connector

Connect the other end of the Adapter Plug to the appr

opriate Smoke Alarm

(connect part C to part B as shown below).

7. Check all connections. Make sure all plugs are completely connected and

snapped together

. Ensure the Adapter Plug is securely connected to the

existing Power Connector

8. Install the base of the Smoke Alarm to the mounting bracket.

9. Restore power to the junction box.

10. Test each Smoke Alarm. Press and hold the test button until the unit alarms.

When testing a series of interconnected units you must test each unit

individually. Make sure all units alarm when each one is tested.

NOTE:

NOTE: Adapter Plug can be used on FIREX

Models manufactured on or

before January 1, 2004.

COMPATIBLE BRK

MODELS

All of the listed BRK

and First Aler

Alarms ar

e compatible with the listed

FIREX

Alarms and will work with the enclosed Adapter Plugs.

BRK

Alarms

4120, 9120 Series – AC, AC/DC Ion, Silence

5919 – AC Photo

2002RAC – AC/DC Photo

7010 Series – AC, AC/DC Photo, Silence

SC6120B, SC9120B – AC/DC Smoke/CO Combo

HD6135FB – Heat Alarm

RM3 – Auxiliary Relay

FIREX

406 (Model #G-6) – AC Ion

4518 (Model #ADC) – AC/DC Ion, Battery in Rear

4618 (Model #FADC) – AC/DC Ion

5000 (Model #FADC) – AC/DC Ion, Latching LED

484 (Model #PG-40) – AC Photo

4480 (Model #PAD) – AC/DC Photo

5700 (Model #ADH) – Heat Alarm

499 – Auxiliary Relay

•

Maximum of only 12 units (except model G-6) may be interconnected.

Check for model numbers above.

Adapter Plug (ADF) Diagram for FIREX

Models:

White

Orange

Black

NOTE: ADAPTER PLUG CANNOT BE USED TO CONNECT

FIREX

CARBON

MONOXIDE ALARMS.

THE ABOVE MODELS OF FIREX

ARE THE ONLY MODELS THAT MAY BE

INTERCONNECTED USING ONE OF THE ADAPTER PLUGS INCLUDED.

IF THE MODEL IS NOT LISTED, IT MUST BE REMOVED FROM THE SYSTEM.

3055574

RECOGNIZED

COMPONENT

CONFORMS TO

UL ST

ANDARD 1977

Side View

Plug Pin

iew

NOTE: T

wist tie should not be r

emoved.

The Parts of This Installation

A Mounting Bracket

BRK

4120, 9120 Series

Smoke Alarm

C ADF Adapter

D Existing compatible

power connector

Electrical Rating:

120V AC, 100mA Maximum

Not for Current Interruption

Bedienungsanleitung

Sehen Sie sich hier kostenlos das Handbuch für First Alert ADF-12 an. Dieses Handbuch fällt unter die Kategorie Rauchmelder und wurde von 1 Personen mit einem Durchschnitt von 7.5 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum First Alert ADF-12 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Brauchen Sie Hilfe?

Haben Sie eine Frage zum First Alert ADF-12 und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere First Alert ADF-12-Besitzer, Ihnen eine gute Antwort zu geben.

Anzahl der Fragen: 0