GE ABS45DFWS

GE ABS45DFWS Bedienungsanleitung

(1)
  • 9
    LEVEL THE RANGE
    WARNING: Never completely remove the leveling leg
    as the range will not be secured to the anti-tip device properly.
    MODELS WITH STORAGE DRAWER OR KICK PANELS
    A
    Plug in unit and slide into place. Pull drawer out until it stops.
    B
    Lift front of drawer until the stops clear the guide. Remove the drawer.
    C
    Install the oven shelves in the oven and position the range where
    it will be installed.
    D
    Check for levelness by placing a spirit level on one of the oven shelves.
    7DNHWZRUHDGLQJV³ZLWKWKHOHYHOSODFHGGLDJRQDOO\ILUVW
    in one direction and then the other.
    E
    The front leveling legs can be adjusted from the bottom
    and the rear legs can be adjusted from the top or the bottom.
    F
    Use an adjustable wrench to adjust the leveling legs until
    the range is level.
    BEFORE YOU BEGIN
    Read these instructions completely and
    carefully.
    ,03257$17³ Save these instructions
    for local inspector’s use.
    ,03257$17³ Observe all
    governing codes and ordinances.
    Note to Installer – Be sure to leave these
    instructions with consumer.
    Note to consumer – Keep these
    instructions for future reference.
    Skill level – Installation of this appliance
    requires a qualified installer or electrician.
    Proper installation is the responsibility of the
    installer.
    Product failure due to improper installation is
    not covered under warranty.
    FOR YOUR SAFETY:
    If you did not receive an anti-tip bracket with your purchase,
    call 1.800.626.8774 to receive one at no cost. (In Canada,
    call 1.800.561.3344.) For installation instructions of the bracket,
    visit: www.GEAppliances.com. (In Canada, www.GEAppliances.ca.)
    Installation Instructions
    Free-Standing Electric Ranges
    MATERIALS YOU MAY NEED TOOLS YOU WILL NEED
    (UL Listed 40 AMP)
    4-Wire Cord 4’ long OR
    3-Wire Cord 4’ long
    Squeeze Connector
    (For Conduit
    Installations Only)
    1
    REMOVE PACKAGING MATERIALS: Failure to remove packaging materials could
    result in damage to the appliance. Remove all packing parts from oven, racks, heating elements
    and drawer. Also, remove protective film and labels on the outer door, cooktop and control panel.
    Drill with 1/8” Bit
    Safety Glasses
    Adjustable Wrench
    Level
    Tin Snips
    Tape Measure
    Pliers
    1/4” Nut Driver
    A child or adult can tip the range and be killed.
    Install the anti-tip bracket to the wall or floor.
    Engage the range to the anti-tip bracket by sliding the
    range back such that the foot is engaged.
    • Re-engage the anti-tip bracket if the range is moved.
    • Failure to do so can result in death or serious burns
    to children or adults.
    Tip-Over Hazard
    WARNING
    Questions? Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com
    In Canada, call 1.800.
    561.3344
    or visit www.GEAppliances.ca
    WARNING
    ³
    Before beginning
    the installation, switch power off at service
    panel and lock the service disconnecting
    means to prevent power from being
    switched on accidentally. When the service
    disconnecting means cannot be locked,
    securely fasten a prominent warning device,
    such as a tag,
    to the service panel.
    2
    PREPARE THE OPENING (FOR INDOOR USE ONLY)
    See illustrations for all rough-in and spacing dimensions. The range may be placed with 0”
    clearance (flush) at the back wall and side walls of the cabinet.
    A
    NOTE C
    B
    A
    C
    Both
    Sides
    NOTE: Use a 4’ power cord to prevent interference
    with the storage drawer. Power cords 4
    1
    ø2’ to 6’ long
    may have to be dressed to allow for proper drawer
    closing.
    MINIMUM DIMENSIONS BETWEEN COOKTOP,
    WALLS AND ABOVE THE COOKTOP:
    A. Make sure the wall covering, countertop, flooring
    and cabinets around the range can withstand the
    heat (up to 200°F) generated by the range.
    B. Allow 30” minimum clearance between surface
    units and bottom of unprotected wood or metal
    cabinet, or allow a 24” minimum when bottom
    of wood or metal cabinet is protected by no less
    than 1/4” thick flame retardant millboard covered
    with not less than No 28 MSG sheet metal, (.015”),
    .015” thick stainless steel, .024”
    aluminum or .020” copper.
    C. This appliance has been approved for 0” spacing to adjacent surfaces above the cooktop. However,
    a 6” minimum spacing to surfaces less than 15” above the cooktop and adjacent
    cabinet is recommended to reduce exposure to steam, grease splatter and heat.
    To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space
    above the cooktop should be avoided. If cabinet storage space is to be provided above
    the cooktop, the risk can be reduced by installing a range hood that projects at least 5” beyond
    the front of the cabinets. Cabinets installed above the cooktop must be no deeper than 13”.
    3
    ELECTRICAL REQUIREMENTS
    WARNING: This appliance must be properly grounded.
    WARNING:
    All new constructions, mobile homes, recreational vehicles and installations where
    local codes do not allow grounding through neutral, require a 4-conductor UL-listed range cord.
    WARNING: To prevent fire or shock, do not use an extension cord with this appliance.
    WARNING: To prevent shock, remove house fuse or open circuit breaker before
    beginning installation.
    We recommend you have the electrical wiring and hookup of your range connected by a qualified
    electrician. After installation, have the electrician show you how to disconnect power from the range.
    You must use a single-phase, 120/208 VAC or 120/240 VAC, 60 hertz electrical system. If you connect
    to aluminum wiring, properly installed connectors approved for use with aluminum wiring must be
    used.
    Effective January 1, 1996, the National Electrical Code requires that new construction (not
    existing) utilize a 4-conductor connection to an electric range. When installing an electric range
    in new construction, mobile home, recreational vehicle, or an area where local codes prohibit
    grounding through the neutral conductor, refer to the section on four-conductor branch circuit
    connections.
    Check with your local utilities for electrical codes which apply in your area. Failure to wire your oven
    according to governing codes could result in a hazardous condition. If there are no local codes, your
    oven must be wired and fused to meet the National Electrical Code, NFPA No.
    70 – latest edition, available from the National Fire Protection Association.
    This appliance must be supplied with the proper voltage and frequency, and connected to an
    individual, properly grounded, 40 amp (minimum) branch circuit protected by a circuit breaker
    or time-delay fuse.
    Use only a 3-conductor or a 4-conductor UL-listed range cord. These cords may be provided with ring
    terminals on wire and a strain relief device.
    A range cord rated at 40 amps with 125/250 minimum volt range is required. A 50 amp range cord
    is not recommended but if used, it should be marked for use with nominal 1
    3
    ø8” diameter connection
    openings. Care should be taken to center the cable and strain relief within the
    knockout hole to keep the edge from damaging the cable.
    The rating plate is located on the oven frame or on the side of the drawer frame.
    Note: Use of automatic, wireless or wired external switches that shut off power to the appliances, are
    not recommended for this product.
    Rating plate
    SINGLE OVEN
    Rating plate
    DOUBLE OVEN
    4
    POWER CORD AND CONDUIT INSTALLATION
    A
    Remove wire cover (on the back of range) by removing screws using a 1/4” nut driver. You can
    access the terminal block by either removing a terminal block cover (on some models) or the
    wire cover. Do not discard these screws.
    B
    For power cord and 1” conduit only,
    remove the
    knockout ring (1
    3
    ø8”) located on bracket directly
    below the terminal block. To remove the
    knockout, use a pair of pliers to bend the
    knockout ring away from the bracket and
    twist until ring is removed.
    D
    For 3/4” conduit installations only, purchase a squeeze connector matching the diameter
    of your conduit and assemble it in the hole. Insert the conduit through the squeeze connector
    and tighten. Allow enough slack to easily attach the wires to the terminal block. NOTE: Do not install the
    conduit without a squeeze connector. The squeeze connector MUST be installed before reinstalling
    the rear range wiring cover.
    Wire cover
    5 screws to
    remove wire
    cover
    Retaining
    tabs
    Back of range
    Terminal block cover
    Screw to
    remove
    terminal
    block cover
    Back of range
    Knockout
    ring in
    bracket
    Knockout ring
    removed
    Terminal block
    (appearance
    may vary)
    C
    For power cord installations only
    (see the next step if using conduit),
    assemble the strain relief in the hole. Insert
    the power cord through the strain relief
    and tighten. Allow enough slack
    to easily attach the cord terminals to
    the terminal block. If tabs are present at
    the end of the winged strain relief, they
    can be removed for better fit.
    NOTE: Do not install the power cord without a
    strain relief. The strain relief bracket MUST be
    installed before
    reinstalling the rear range wiring cover.
    Power cord
    Strain relief
    Terminal
    block
    Bracket
    Squeeze
    connector
    Terminal block
    Conduit
    Bracket
    Proceed to step 5 or 6.
    5
    3-WIRE INSTALLATION (GROUND IS THROUGH THE NEUTRAL WIRE)
    WARNING: Shock Hazard
    The neutral wire and ground strap must be
    connected as shown below for the range to be
    properly grounded. Do not remove the ground strap.
    Failure follow this instruction may result in potential
    shock hazard.
    WARNING: Fire hazard
    Terminal block screws must be securely tightened.
    Failure to do so may result in potential fire hazard.
    FOR POWER CORD INSTALLATION
    A. Remove the 3 lower screws from the terminal
    block. Do not loosen the upper screws.
    B. Do not cut or remove the ground strap.
    C. Insert the 3 screws through each power cord
    terminal ring and back into the terminal block. Be
    certain the white wire is in the center. Securely
    tighten each screw (35 to 50 in-lbs.)
    FOR CONDUIT INSTALLATION
    A. Loosen the 3 lower screws on the terminal block. Do not
    loosen the upper screws.
    B. Do not cut or remove the ground strap.
    C. Insert the bare wire tip (insulation stripped 5/8”) into the
    bottom terminal block openings. Be certain the white
    wire is in the center. On certain models, the wire must
    be inserted through an opening in the ground strap.
    Securely tighten each screw onto each wire (35 to 50
    in-lbs.).
    NOTE: Aluminum building wire may be used but it must be
    rated for the correct amperage and voltage.
    PROCEED TO STEP 7.
    31-10892
    05-13 GE
    6
    4-WIRE INSTALLATION (SEPARATE GROUND WIRE)
    WARNING: Shock Hazard
    The neutral wire and ground strap must be
    connected as shown below for the range to
    be properly grounded. Do not remove the
    ground strap. Failure follow this instruction
    may result in potential shock hazard.
    WARNING: Fire hazard
    Terminal block screws must be securely
    tightened. Failure to do so may result in
    potential fire hazard.
    FOR POWER CORD INSTALLATION
    A. Remove the 3 lower screws from the
    terminal block. Do not loosen the upper screws.
    B. Remove the ground screw and ground plate
    and retain them.
    C. Cut the ground strap below the terminal
    block and discard the lower section.
    D. Insert the ground screw through the ground
    plate (removed earlier) and back into the
    range frame. Tighten securely, but do not
    over-tighten (15 to 20 in-lbs.)
    E. Insert the 3 terminal screws through each
    power cord terminal ring and back into the
    terminal block. Be certain the white wire is
    in the center. Securely tighten each screw
    (35 to 50 in-lbs.
    FOR CONDUIT INSTALLATION
    A. Remove the 3 lower screws from the
    terminal block. Do not loosen the upper screws.
    B. Remove the ground screw and ground plate
    and retain them.
    C. Cut the ground strap below the terminal block
    and discard the lower section.
    D. Insert the bare ground bare wire tip (insulation
    stripped 5/8”) between the range frame
    and the ground plate (removed earlier)
    and secure it in place with the ground
    screw. Tighten securely, but do not over-
    tighten (15 to 20 in-lbs).
    E. Insert the wire tips (insulation stripped 5/8”)
    into the bottom terminal block openings. Be
    certain the white wire is in the center. On
    certain models, the wire must be inserted
    through an opening in the ground strap.
    Securely tighten each screw onto each wire
    (35 to 50 in-lbs.)
    NOTE: Aluminum building wire may be used but it must be rated for the correct amperage and voltage.
    7
    REPLACE THE WIRE COVER
    Replace wire cover on range back by sliding its left edge under the retaining tabs and replace the
    screws removed earlier. Make sure that no wires are pinched between cover and range back.
    Wire cover
    5 screws to
    remove wire
    cover
    Retaining
    tabs
    Back of range
    Terminal
    block cover
    Screw to
    remove
    terminal
    block cover
    Back of range
    8
    ANTI-TIP DEVICE INSTALLATION
    To reduce the risk of tipping the range, the
    range must be secured by a properly installed
    anti-tip bracket. See installation instructions
    shipped with the bracket for complete details
    before attempting to install.
    To check if the bracket is installed and
    engaged properly, look underneath the range
    to see that the rear leveling leg is engaged
    in the bracket. On some models, the storage
    drawer or kick panel can be removed for
    easier inspection. If visual inspection is not
    possible, slide the range forward, confirm the anti-tip bracket is securely attached to the floor or wall, and
    slide the range back so the leveling leg is under the anti-tip bracket. If the range is pulled from the wall for
    any reason, always repeat this procedure to verify the range is properly secured by the anti-tip bracket.
    Never completely remove the leveling legs or the range will not be secured to the anti-tip bracket.
    • A child or adult can tip the range and be killed.
    • Install the anti-tip bracket to the wall or floor.
    • Engage the range to the anti-tip bracket by sliding the
    range back such that the foot is engaged.
    • Re-engage the anti-tip bracket if the range is moved.
    • Failure to do so can result in death or serious burns
    to children or adults.
    Tip-Over Hazard
    WARNING
    Stop
    10
    FINAL INSTALLATION CHECKLIST
    Check to make sure the circuit breaker is closed (RESET) or the circuit fuses are replaced.
    Be sure power is in service to the building.
    Check that all packing materials and tape have been removed. This will include tape on metal panel under
    control knobs (if applicable), adhesive tape, wire ties, cardboard and protective plastic. Failure to remove
    these materials could result in damage to the appliance once the appliance has been turned on and
    surfaces have heated.
    Check that the door and drawer are parallel to each other and that both operate smoothly. If they
    do not, see the Owner’s Manual for proper replacement.
    Check to make sure that the rear leveling leg is fully inserted into the Anti-Tip bracket and that the bracket
    is securely installed.
    OPERATION CHECKLIST
    Turn on one of the surface units to observe that the element glows within 60 seconds. Turn the unit
    off when glow is detected. If the glow is not detected within the time limit, recheck the range wiring
    connections. If change is required, retest again. If no change is required, have building wiring checked for
    proper connections and voltage.
    Check that the Clock (on models so equipped) display is energized. If a series of horizontal red
    lines appear in the display, disconnect power immediately. Recheck the range wiring connections.
    If change is made to connections, retest again. If no change is required, have building wiring checked for
    proper connections and voltage. It is recommended that the clock be changed if the red lines appear.
    Be sure all range controls are in the OFF position before leaving the range.
    9
    LEVEL THE RANGE (CONT.)
    G
    Position cord so that it does not interfere with drawer.
    Place drawer rail on guides. Push the drawer in until it stops.
    H
    Lift front of drawer and push in until the stops clear
    the guides.
    I
    Lower the front of the drawer and push in until it closes.
    MODELS WITH BAKING, WARMING DRAWERS OR DOUBLE OVEN
    A
    Plug in the unit.
    B
    Measure the height of your countertop at the rear of the opening (X).
    C
    Adjust two rear leveling legs so that the rear of cooktop is at the same height
    as the counter (Y).
    D
    Slide unit into place.
    E
    Install oven shelves in the oven and position the range where it will be installed.
    F
    Check for levelness by placing a spirit level on one of the oven shelves.
    7DNHWZRUHDGLQJV³ZLWKWKHOHYHOSODFHGGLDJRQDOO\ILUVWLQRQHGLUHFWLRQ
    and then the other.
    G
    Adjust front leveling legs until the range is level.
    X
    Y
    Leg
    leveler
    Lower
    range
    Raise
    range
    Spirit level
    Anti-Tip Bracket
    Kit Included
    Ground
    strap
    Terminal block
    (appearance
    may vary)
    Neutral
    terminal
    Power cord
    Ground
    plate
    Power Cord
    Wire
    tips
    Terminal
    block
    Conduit
    Conduit
    Red or
    Black
    Red or
    Black
    Red or
    Black
    Red or
    Black
    White
    White
    Terminal
    block
    Red or
    Black
    Red or
    Black
    Neutral
    terminal
    Ground plate
    (grounding to
    range)
    Ground
    screw
    After–Power Cord
    Green
    or Bare
    White
    Before–Power Cord and Conduit
    Terminal
    block
    Neutral
    terminal
    Ground
    strap
    Ground strap
    or
    After–Conduit
    Terminal
    block
    Ground plate
    (grounding to
    range)
    Wire
    tips
    Ground
    screw
    Red or
    Black
    Red or
    Black
    White
    Green
    or Bare
    8 1/2
    Cord
    Wall
    Floor
    7”
    5”
    Outlet
    box
    2
    1
    ø4
    7
    1
    ø2
    7
    1
    ø2
    3
    1
    ø2
    Install the
    outlet box
    on either
    side of the C
    L
    C of range
    30”
    36
    1
    ø4
    46 3/4
    26 1/4”
    w/o handle
    29”
    with handle
    L
GE ABS45DFWS

Brauchen Sie Hilfe?

Anzahl der Fragen: 0

Haben Sie eine Frage zum GE ABS45DFWS oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere GE ABS45DFWS-Eigentümer Ihre Frage richtig beantworten.

Sehen Sie sich hier kostenlos das Handbuch für GE ABS45DFWS an. Dieses Handbuch fällt unter die Kategorie Backöfen und wurde von 1 Personen mit einem Durchschnitt von 6.2 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum GE ABS45DFWS oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

GE ABS45DFWS-Spezifikationen

Allgemeines
Marke GE
Model ABS45DFWS
Produkte Backofen
Sprache Englisch
Dateityp PDF

Häufig gestellte Fragen

Nachfolgend finden Sie die am häufigsten gestellten Fragen zu GE ABS45DFWS .

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Bedienungsanleitu.ng

Auf der Suche nach einer Bedienungsanleitung? Bedienungsanleitu.ng sorgt dafür, dass Sie in Windeseile die Bedienungsanleitung finden, die Sie suchen. In unserer Datenbank befinden sich mehr als 1 Million PDF Bedienungsanleitungen von über 10.000 Marken. Jeden Tag fügen wir die neuesten Bedienungsanleitungen hinzu, damit Sie jederzeit das Produkt finden, das Sie suchen. Es ist ganz einfach: Tippen Sie in der Suchleiste Markenname und Produkttyp ein und Sie können direkt die Bedienungsanleitung Ihrer Wahl gratis online einsehen.

Bedienungsanleitu.ng

© Copyright 2020 Bedienungsanleitu.ng. Alle Rechte vorbehalten.

Diese Website benutzen Cookies. Wenn Sie die Website weiter nutzen, stimmen Sie der Verwendung von Cookies zu.

Erfahren Sie mehr