GE GFW550SSNWW Bedienungsanleitung

GE GFW550SSNWW
8.4 · 2
PDF Bedienungsanleitung
 · 2 Seiten
Englisch
BedienungsanleitungGE GFW550SSNWW
r Water Hoses with
90° elbows (2)
r Rubber washers (2)
and strainer screens
(2)
TOOLS NEEDED
r Adjustable
wrench
r Channel-lock
pliers
r Phillips
Screwdriver
r Level
PARTS SUPPLIED
r Cable tie
r
Hose
guide
1 Unpack your washer
r
4 Shipping bolt
covers
Once the washer is within
4 feet of its destination, use
a 1/2” wrench or socket to
remove the following from
the back side:
4 shipping bolts
4 plastic spacers (including
power cord retainers and
rubber grommets)
1 bracket
Insert the hole caps in the bolt holes
once the shipping bolts and spacers
have been removed. Save all shipping
support hardware for future use.
Recycle or destroy the carton
after the washer is unpacked.
2 Remove shipping hardware
PARTS REQUIRED
(Sold separately or
included with the
GFW510 model)
GE Appliances recommends inlet hoses that have a 90° bend at one end.
The 90° bend should be installed at the washer as shown above.
Run water from both faucets

particles that might clog the water
valve screens.
Ensure that a rubber washer is
in the end of the hot and cold
hoses.
Connect the inlet hoses to the hot
“H” outlet and cold “C” outlet.
Hand-tighten and then tighten
them another 2/3 turn with pliers.
Do not crossthread or over-tighten
these connections.
3 Connect hoses to washer
Scan this
code to watch
a video on
Step 2.
Ensure that a screen washer is
inserted into the faucet end of
both hoses with protruded side
facing the faucet. If a rubber
washer is already inserted,
remove before inserting screen
washer.
Connect the inlet hose from
the “H” outlet to the hot faucet
and the inlet hose from the “C
outlet to the cold faucet.
Hand-tighten and then tighten
them another 2/3 turn with
pliers.
Turn on the water and check
for leaks.
4 Connect hoses to water supply
Gently rock the washer into

hoses do not become kinked.
Do not use door or dispenser
drawer to lift the washer.
Place level on top.
Adjust the front leveling legs up
or down to ensure the washer
is resting solidly.
Turn the lock nuts on each
leg up toward the base of
the washer and snug with a
wrench.
Level washer both side-to-side
and front-to-back.
5 Level your washer
Attach U-shaped hose guide to
end of drain hose.
Place hose in laundry tub or
standpipe and secure with cable
tie.
If placed in standpipe, the end
of the drain hose should extend
only 4 to 7 inches down the pipe.
6 Install drain hose and plug
Plug washer into
a grounded outlet.
Do not use an
extension cord or
adaptor plug.
7 Optional: Reverse the washer door 8 Final installation checklistVideo
Scan this
code to watch
a video on
Step 5.

QUICK INSTALLATION GUIDE

Instructions en Français - Voir le Guide de l’utilisateur et instruction d’installation • Instrucciones en Español - Ver el Manual del propietario e instalación
DO NOT DISCARD. KEEP FOR FUTURE USE.
STOP

WARNING

For your safety
persons when using or installing the product, read and obey all safety information provided in the Owner’s Manual & Installation Instructions that accompanied the product.• Do not install or store appliance in an area where it will be exposed to dripping water or outside weather conditions. See Location of Your Washer section in the Owner’s Manual & Installation Instructions.
NOTE: This appliance must be properly grounded and installed
as described in these steps and the Owner’s Manual & Installation Instructions. Electrical service to the washer must conform with local codes and ordinances and the latest edition of the national Electrical Code, ANSI/NFPA 70.
r Lock Bar (For
Reversing the
Door Swing)
Remove
Install
Video
Leveling
Leg
Level
Cable
Tie
If you desire to reverse the door,
perform step 7 now.
r
Main power is turned on. The washer is plugged in.
r
Faucets are turned on. Water hoses are connected securely

r

r
Shipping bolts and spacers are removed and stored for future
use.
r
Drain hose is placed in tub or standpipe and secured with a
cable tie.
r
Run a load of clothes using the Quick Wash cycle. Check for
leaks.
r
When the load is spinning at high speed, ensure that the
washer and leveling legs are stable.
While supporting the open door,
remove the screws from the hinge.
Remove the door hinge and cover.
Remove the door striker assembly,
reverse the striker and replace the
assembly on the opposite side.
Replace the door hinge and cover
on the opposite side.
Remove the terminal holder and
disconnect the pin connector.
Remove lock assembly and install
on opposite side.
Reconnect pin connector and
replace the holder.
Replace the door assembly.
This quick reference guide is provided for informational purposes only and does not replace, modify or change in any manner the Owner’s Manual & Installation Instructions.

Getting started

Try these washer features
(not available on all models)UltraFresh Vent™
Works to eliminate
excess moisture to
help prevent odors
so your washer stays
fresh and clean.
OdorBlock™
Microban
®
technology
delivers antimicrobial
durable protection
that lives on load
after load.
SmartDispense™
The dispenser holds
up to 32 loads and
automatically
dispenses the right
amount every time.
1 Step Wash + Dry
Wash and dry
a small load to
eliminate the need
to transfer clothes to
the dryer.
Time Saver
Delivers a thorough
clean for any size
and type of load in
only 35 minutes.
WiFi
Monitor and control
your laundry from
anywhere and receive
real-time updates

dBT™
Onboard sensing
enables real-time
balancing during
spin to save time
and reduce noise.
Troubleshooting Tips...Before you call for service
Before you call for service, see the Troubleshooting Tips section in your
OWNER’S MANUAL & INSTALLATION INSTRUCTIONS.
Service
If needed, schedule a visit from GE Appliances local factory service for advanced
service by visiting localgeappliancerepair.com or calling 866.530.7025.

Care & Cleaning

Cleaning the pump lterCleaning the door gasket
To clean the interior of the
washer, use the SELF CLEAN
cycle using the following
procedure:
Step 1: Remove any garments
or objects from the washer to
ensure the basket is empty.
Step 2: Open the door
and add one cup (250 ml)
of bleach directly into the
washer basket.
Step 3: Close the door and
select the SELF CLEAN
cycle. Press the Start pad.
Step 4: When the SELF
CLEAN cycle is working,
the display will show the
estimated cycle time
remaining. The cycle will
complete in about 90 minutes.
Do not interrupt the cycle.
Step 5: After the cycle is
complete (on some models),
the washer will automatically
start an UltraFresh Vent
operation so that the door
can remain closed until the
next time the washer is used.
SELF CLEAN may be
interrupted by pressing
Start/Pause. When
interrupted, be sure to
run a complete SELF
CLEAN cycle before
using the washer again.
For more information,
please refer to your
OWNER’S MANUAL.
STEP 1: Open the washer
door.
STEP 2: Press down on the
door gasket and pull down
on the interior gasket with
your fingers.
STEP 3: Remove any
foreign objects trapped
inside the interior gasket.
STEP 4: When you are
finished cleaning the door
gasket, release it and the
gasket will return to the
operating position.
NOTE: Make sure nothing
is blocking holes behind
gasket.
NOTE: Clean pump
lter every 6 months
or sooner if unit is
not draining properly.
Cleaning the interior of the washer
Routine maintenance
Genuine GE Appliances Parts and Accessories make appliance maintenance easy by providing cleaning products, replacement parts and accessories that are designed to keep your appliance at peak performance. To order direct visit GEApplianceparts.com or call 877.959.8688.IMPORTANT
• Run SELF CLEAN with tub cleaner once a month.
After the completion of a SELF CLEAN cycle, the interior
of your washer may have a bleach smell.
It is recommended to run a RINSE & SPIN or a light
color load after the SELF CLEAN cycle.
Step 1
Load clothes into
your washer and
close the door.
Step 1: Open
the access door

screwdriver in the
notch of the door
and pull down the
pour spout.
Step 2: Place a
shallow pan or dish
under the pump
access door and

for protection. It is
normal for up to a
cup of water to drain

Step 3: Turn

counterclockwise

slowly to let the water
drain.
Step 4: Clean the

Step 5: Replace the


clockwise until
tightened securely. Flip
up the pour spout and
close the access door.
Scan this code
to watch a
video
on this topic.
Video
GE is a trademark of the General Electric Company. Manufactured under trademark license.

QUICK REFERENCE GUIDE

Step 2
Turn the knob
to wake up the
display and select
your desired cycle.
Step 3
Open the dispenser
to add detergent,
or on models with
SmartDispense
select the
SmartDispense
setting as desired.
Step 4
Press Start to begin
the wash cycle.
When nished, the
door will unlock.
Step 5
For washers equipped
with the UltraFresh
Vent, select this
option to eliminate
excess moisture when
you’re done with laundry
for awhile. Otherwise,
leave your washer door
slightly ajar.
OR
SmartDispense
Use only HE
High-Efficiency
detergent
0020508637
49-3000218 Rev 3
03-21 GEA
H
(Hot)
C
(Cold)

Bedienungsanleitung

Sehen Sie sich hier kostenlos das Handbuch für GE GFW550SSNWW an. Dieses Handbuch fällt unter die Kategorie Waschmaschinen und wurde von 2 Personen mit einem Durchschnitt von 8.4 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum GE GFW550SSNWW oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Brauchen Sie Hilfe?

Haben Sie eine Frage zum GE GFW550SSNWW und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere GE GFW550SSNWW-Besitzer, Ihnen eine gute Antwort zu geben.

Anzahl der Fragen: 0

GE GFW550SSNWW-Spezifikationen

Nachfolgend finden Sie die Produktspezifikationen und die manuellen Spezifikationen zu GE GFW550SSNWW.

Allgemeines
Marke GE
Model GFW550SSNWW
Produkte Waschmaschine
EAN 084691849339
Sprache Englisch
Dateityp Benutzerhandbuch (PDF), Datenblatt (PDF), Energiekennzeichnung (PDF)

Häufig gestellte Fragen

Finden Sie die Antwort auf Ihre Frage nicht im Handbuch? Vielleicht finden Sie die Antwort auf Ihre Frage in den FAQs zu GE GFW550SSNWW unten.

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Keine Ergebnisse