GE JK3800DHBB

GE JK3800DHBB Bedienungsanleitung

(1)
  • 2 C
    CUTOUT FOR DOUBLE OVENS
    (2 THERMAL OVENS)
    NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim
    both sides equally to establish the cutout width.
    Dim. Description 27” Double Oven 30” Double Oven with
    Pedestal
    30” Double Oven
    without Pedestal
    A Cabinet Width 27” (68.6 cm) 30” (76.2 cm) 30” (76.2 cm)
    B Cutout Width 25” (63.5 cm) min.
    25
    1
    ø4” (64.1 cm) max.
    28
    1
    ø2” (72.4 cm) min.
    28
    5
    ø8” (72.7 cm) max.
    28
    1
    ø2” (72.4 cm) min.
    28
    5
    ø8” (72.7 cm) max.
    C Cutout Height
    49
    11
    ø16” (126.2 cm) min.
    50
    1
    ø8” (127.3 cm) max.
    51
    13
    ø16” (131.6 cm) min.
    51
    15
    ø16” (131.9 cm) max.
    50 ¼” (127.64cm)
    D Overlap of Oven
    Over Side Edges
    of Cutout
    1” (2.5 cm)
    11
    ø16” (1.75 cm)
    11
    ø16” (1.75 cm)
    E
    Clearance to
    Adjacent Corners,
    Drawers, Walls, etc.,
    When Door Is Open
    23” (58.4 cm) min. 23” (58.4 cm) min. 23” (58.4 cm) min.
    F Overlap of Oven
    Top of Cutout
    1” (2.5 cm) min. 1” (2.5 cm) min.
    (1
    1
    ø
    4
    ” (3.2 cm) for PT9550)
    1” (2.5 cm) min.
    (1
    1
    ø
    4
    ” (3.2 cm) for PT9550)
    G Overlap of Oven
    Bottom of Cutout
    1” (2.5 cm) min. 1
    1
    ø4” (3.2 cm) 1
    1
    ø4” (3.2 cm)
    H Junction Box
    Location
    8
    3
    ø4” (22.2 cm) max.
    right side only
    9
    1
    ø2” (24.1 cm) max.
    right side only
    9
    1
    ø2” (24.1 cm) max.
    right side only
    J Height to Bottom
    of Junction Box
    44” (111.8 cm) 47” (119.4 cm) 47” (119.4 cm)
    K Recommended
    Cutout Location
    from Floor
    13
    1
    ø4” (33.7 cm) 12” (30.5 cm) 12” (30.5 cm)
    2 A
    CUTOUT FOR SINGLE OVENS IN WALL CABINET
    NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim
    both sides equally to establish the cutout width.
    BEFORE YOU BEGIN
    Read these instructions completely and
    carefully.
    ,03257$17³ Save these instructions
    for local inspector’s use.
    ,03257$17³ Observe all governing
    codes and ordinances.
    Note to Installer – Be sure to leave these
    instructions with Consumer.
    Note to Consumer – Keep these instructions
    for future reference.
    Skill level – Installation of this appliance
    requires a qualified installer or electrician.
    Proper installation is the responsibility
    of the installer.
    Product failure due to improper installation
    is not covered under Warranty.
    Product is for indoor use only.
    Installation Instructions
    27” & 30” Electric Built-In Wall Ovens
    FOR YOUR SAFETY:
    WARNING
    :
    Before beginning the installation, switch power off at the service panel and
    lock the service disconnecting means to prevent power from being switched on accidentally. When the
    service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,
    to the service panel.
    Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure.
    Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,
    stand or hang on the oven door.
    Make sure the wall coverings, counters and cabinets around the oven can withstand the heat
    (up to 200°F [93.3°C]) generated by the oven.
    Questions? Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com
    In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca
    MATERIALS YOU MAY NEED
    Junction Box
    Wire Nuts
    Strain Relief Clamp for 1/2” Conduit
    36” (91 cm) of String
    TOOLS YOU MAY NEED
    1/8” Drill Bit and Electric or Hand Drill
    Phillips Screwdriver
    Wire Strippers
    7/16” Nut Driver
    T20 Screwdriver (hinge bracket)
    1/4” Nut Driver
    1
    REMOVE PACKAGING MATERIALS
    Failure to remove packaging materials could result in damage to the appliance. Remove all packing
    parts from oven, racks and heating elements. Remove protective film and labels on the outer door
    and control panel. Also, remove plastic on trims and panel, all tape around the oven and any shipping
    screws securing the oven to the base pad. Open oven door and remove literature pack and oven
    racks. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation
    process. The trim is wrapped separately and taped to the top of the unit. Remove pedestal rails from
    seperate box and set aside (30” Double Wall Ovens Only).
    2
    PREPARE THE OPENING
    NOTE: If the cabinet does not have a solid bottom, two
    braces or runners must be installed to support the weight
    of the oven. For single ovens, the runners and braces
    must support 200 lbs (91 kg). For double ovens, the
    runners and braces must support 375 lbs. (170 kg).
    NOTE: If marks, blemishes or the cutout opening are
    visible above the installed oven, it may be necessary to
    add wood shims under the runners and front trim until
    the marks or opening are covered.
    NOTE: If the cabinet does not have a front frame and
    the sides are less than ¾” (1.9 cm) thick, shim both sides
    equally to establish the cutout width.
    ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired) into an
    approved junction box. A plug and receptacle is NOT permitted on these products.
    These ovens
    are not
    approved for
    stackable
    installations.
    Cutout –
    observe all
    dimensions and
    requirements.
    Cutout –
    observe all
    dimensions and
    requirements.
    2” (5.1 cm) Min.
    30.5” (77.5 cm)
    30” models
    27” (68.58 cm)
    27” models
    Center Line Center Line
    Side-by-Side Installations
    Install two ovens in separate cutouts.
    Dimension Dimension Description 27” Single Oven 30” Single Oven
    A Cabinet Width 27” (68.6 cm) 30” (76.2 cm)
    B Cutout Width 25” (63.5 cm) min. 28
    1
    ø2” (72.4 cm) min.
    25
    1
    ø4” (64.1 cm) max. 28
    5
    ø8” (72.7 cm) max.
    C Cutout Height 27
    5
    ø8” (70.2 cm) min. 27
    1
    ø4” (69.2 cm) min.
    28
    1
    ø8” (71.4 cm) max. 27
    5
    ø16” (69.4 cm) max.
    D Overlap of Oven Over 1” (2.5 cm)
    11
    ø16” (1.75 cm)
    Side Edges of Cutout
    E Clearance to 23” (58.4 cm) min. 23” (58.4 cm) min.
    Adjacent Corners,
    Drawers, Walls, etc.,
    When Door Is Open
    F Overlap of Oven 1” (2.5 cm) min. 1” (2.5 cm) min.
    Top of Cutout (1
    1
    ø4” (3.2 cm) for PT9050)
    G Overlap of Oven 1” (2.5 cm) min. 1
    1
    ø4” (3.2 cm)
    Bottom of Cutout
    H Junction Box Location 8
    3
    ø4” (22.2 cm) max. 9
    1
    ø2” (24.1 cm) max.
    right side only right side only
    Suitable
    Bracing
    to Su
    pp
    ort
    C
    L
    2" x 4" (5 cm x 10 cm)
    or Equivalent Runners Level
    with Bottom of Cutout
    and Flush with Sides of Cutout
    2 B
    CUTOUT FOR SINGLE OVENS – UNDER COUNTER
    NOTE: These ovens are only approved to be installed under the specific models as labeled on the unit.
    Dimension Dimension Description 27” Single Oven 30” Single Oven
    A Cabinet Width 25” (63.5 cm) min. 28
    1
    ø2” (72.4 cm) min.
    25
    1
    ø4” (64.1 cm) max. 28
    5
    ø8” (72.7 cm) max.
    B Cutout Height 27
    5
    ø8” (70.2 cm) min. 27
    1
    ø4” (69.2 cm) min.
    28
    1
    ø8” (71.4 cm) max. 27
    5
    ø16” (69.4 cm) max.
    C Unit Overlap Top 1” (2.5 cm) 1” (2.5 cm)
    (1
    1
    ø4” (3.2 cm) for PT9050)
    D Unit Overlap Bottom 1” (2.5 cm) 1
    1
    ø4” (3.2 cm)
    E Unit Overlap Side Edges 1” (2.5 cm)
    11
    ø16” (1.75 cm)
    F Junction Box Location 8
    3
    ø4” (22.2 cm) max. 9
    1
    ø2” (24.1 cm) max.
    right side only right side only
    Continue to Section 4.
    NOTE: One cooktop may be centered over either oven in
    the side-by-side installation.
    Cutout – observe
    all dimensions and
    requirements.
    2” (5.1 cm) Min.
    30.5” (77.5 cm) 30” models
    27” (68.58 cm) 27” models
    Center Line Center Line
    Side-by-Side Installations
    Install two ovens in separate cutouts.
    Cooktop
    Cutout – observe
    all dimensions and
    requirements.
    2 F
    CUTOUT FOR INSTALLATION OVER A WARMING DRAWER
    NOTE: Install the oven only with specific models listed on the label located on top of the oven.
    NOTE: Additional clearances between cutouts may be required. Check to be sure the oven supports
    above the Warming Drawer location do not obstruct the required interior depth and height.
    When installing a Warming Drawer below a single or double oven, a separate 120V, 60 HZ, properly
    grounded receptacle must be installed. Refer to installation instructions packed with
    the Warming Drawer for specific installation requirements.
    2 E
    SECURING UPPER MICROWAVE/ADVANTIUM OVEN TO CABINET
    For double oven with microwave or Advantium upper ovens. Secure a wooden cleat to side of cabinet
    so that the upper oven can be secured to the cleat with provided screws
    27” Cabinet requirements
    No shims (or cleats) required when cabinet is in minimum
    width condition.
    If cabinet is at maximum width condition, add wood
    shims to bring cabinet to minimum condition.
    30” Cabinet requirements
    No shims (or cleats) required when cabinet is in minimum
    width condition.
    If cabinet is at maximum width condition, fix the wood
    cleats as shown in illustration.
    2 D
    CUTOUT FOR DOUBLE OVENS (with Upper Microwave Oven)
    NOTE: If the cabinet does not have a front frame and the sides are less than ¾” (1.9 cm) thick, shim
    both sides equally to establish the cutout width.
    Anti-Tip Block Against
    Rear Wall Per Warming
    Drawer Requirement
    2" (5.1 cm)
    Min.
    Per Warming
    Drawer
    Requirement
    Continue to Section 3 for DWO with Pedestal. Otherwise, continue to Section 4.
    DESIGN INFORMATION
    SINGLE OVEN INSTALLATIONS
    The single oven may be installed in a cabinet alone or above a warming drawer. The single oven may also
    be installed below a countertop or below specified cooktops. See the label on top of the oven for approved
    models.
    DOUBLE OVEN INSTALLATIONS
    A double oven may be installed in a cabinet alone or above a warming drawer. See the label on top of the
    oven for approved models.
    IMPORTANT: Always refer to individual installation instructions packed with each product for specific
    requirements.
    Continue to Section 4
    Continue to Section 4.
    H
    B
    F
    G
    C
    D
    A
    E
    Junction
    Box
    Location
    (junction
    box may
    be located
    in adjacent
    cabinet)
    22” (55.9
    cm) Min. to
    Bottom of
    Junction
    Box
    Cutout Depth
    23-1/2”
    (59.7 cm) Min.
    Recommended
    Cutout Location
    from Floor
    32-1/2” (82.6 cm)
    Opening
    Between Inside
    Walls Must be
    at Least 28-1/2”
    (72.4 cm) Wide
    H
    B
    C
    K
    F
    G
    D
    A
    J
    E
    Junction
    Box
    Location
    (junction
    box may
    be located
    in adjacent
    cabinet)
    Cutout Depth
    23-1/2”
    (59.7 cm) Min.
    Note: Allow
    1/4” (0.64 cm)
    clearances
    from side
    edges of oven
    door.
    3
    PEDESTAL RAIL INSTALLATION (30” DOUBLE OVENS ONLY)
    A. Place one pedestal rail on each cabinet runner or centered on opposite side of solid cabinet bottom
    flush with side of cabinet opening. Locate each rail so that front of rail is behind front cabinet
    opening.
    B. Drill pilot holes and attach rails to runner or bottom of cabinet with provided hardware.
    Dim. Description 27” Oven
    with Microwave
    30” Oven
    with Microwave
    A Cabinet Width 27” (68.6 cm) 30” (76.2 cm)
    B Cutout Width 25” (63.5 cm) min.
    25
    1
    ø4” (64.1 cm) max.
    28
    1
    ø2” (72.4 cm) min.
    28
    5
    ø8” (72.7 cm) max.
    C Cutout Height
    41
    1
    ø8” (104.5 cm) min.
    41
    1
    ø4” (104.8 cm) max.
    42
    3
    ø16” (107.2 cm) min.
    42
    1
    ø4” (107.3 cm) max.
    D Overlap of Oven Over Side Edges
    of Cutout
    1” (2.5 cm)
    11
    ø16” (1.75 cm)
    E Clearance to Adjacent Corners,
    Drawers, Walls, etc., When Door
    Is Open
    23” (58.4 cm) min. 23” (58.4 cm)
    F Overlap of Oven Top of Cutout 1” (2.5 cm) min. 1” (2.5 cm) min.
    G Overlap of Oven Bottom of Cutout 1” (2.5 cm) min. 1
    1
    ø4” (3.2 cm)
    H Junction Box Location 8
    3
    ø4” (22.2 cm) max.
    right side only
    9
    1
    ø2” (24.1 cm) max.
    right side only
    6.375”
    27.5”
    1.5”
    3.0”
    Cleat locations on 30” cabinet
    with maximum cutout condition
    Wood Cleats
    4 A
    DOOR REMOVAL (RECOMMENDED)
    NOTE: Door removal is not a requirement for installation of the product but is an added convenience.
    To remove the door:
    A. Open the oven door as far as it will go.
    B. Remove hinge bracket from front frame and set aside. The hinge bracket must
    be replaced for proper door functionality when door is reinstalled.
    C. Push both hinge locks down toward the door frame to the unlocked position.
    This may require a flat-blade screwdriver. DO NOT LIFT THE DOOR BY THE
    HANDLE!
    D. Place hands on both sides of the door and close the oven door to the removal
    position (approximately 1”–2” [2.5 cm–5.1 cm] from the closed position).
    E. Lift the door up and out until the hinge arms clear the slots.
    NOTE: The oven door is very heavy. Be sure
    you have a firm grip before lifting the oven door off the hinges. Use caution
    once the door is removed. Do not lay the door on its handle.
    This could cause dents or scratches.
    Hinge Slot
    Hinge Arm
    Hinge Unlocked Position
    Hinge Clears Slot
    Hinge Bracket
    31-10965-1
    03-14 GE
GE JK3800DHBB

Brauchen Sie Hilfe?

Anzahl der Fragen: 0

Haben Sie eine Frage zum GE JK3800DHBB oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere GE JK3800DHBB-Eigentümer Ihre Frage richtig beantworten.

Sehen Sie sich hier kostenlos das Handbuch für GE JK3800DHBB an. Dieses Handbuch fällt unter die Kategorie Backöfen und wurde von 1 Personen mit einem Durchschnitt von 9.4 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch, Spanisch. Haben Sie eine Frage zum GE JK3800DHBB oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

GE JK3800DHBB-Spezifikationen

Allgemeines
Marke GE
Model JK3800DHBB
Produkte Backofen
Sprache Englisch, Spanisch
Dateityp PDF

Häufig gestellte Fragen

Nachfolgend finden Sie die am häufigsten gestellten Fragen zu GE JK3800DHBB .

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Bedienungsanleitu.ng

Auf der Suche nach einer Bedienungsanleitung? Bedienungsanleitu.ng sorgt dafür, dass Sie in Windeseile die Bedienungsanleitung finden, die Sie suchen. In unserer Datenbank befinden sich mehr als 1 Million PDF Bedienungsanleitungen von über 10.000 Marken. Jeden Tag fügen wir die neuesten Bedienungsanleitungen hinzu, damit Sie jederzeit das Produkt finden, das Sie suchen. Es ist ganz einfach: Tippen Sie in der Suchleiste Markenname und Produkttyp ein und Sie können direkt die Bedienungsanleitung Ihrer Wahl gratis online einsehen.

Bedienungsanleitu.ng

© Copyright 2020 Bedienungsanleitu.ng. Alle Rechte vorbehalten.

Diese Website benutzen Cookies. Wenn Sie die Website weiter nutzen, stimmen Sie der Verwendung von Cookies zu.

Erfahren Sie mehr