Before beginning the installation, switch power off at the service panel and
lock the service disconnecting means to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,
to the service panel.
Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure.
Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,
stand or hang on the oven door.
Make sure the wall coverings, counters and cabinets around the oven can withstand the heat
(up to 200°F [93.3°C]) generated by the oven.
Questions?Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com
In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca
MATERIALS YOU MAY NEED
Junction Box
Wire Nuts
Strain Relief Clamp for 1/2” Conduit
TOOLS YOU MAY NEED
1/8” Drill Bit and Electric or Hand Drill
Phillips Screwdriver
Wire Strippers
1
REMOVE PACKAGING MATERIALS
Failure to remove packaging materials could result in damage to the appliance. Remove all packing
parts from oven, racks and heating elements. Remove protective film and labels on the outer door
and control panel. Also, remove plastic on trims and panel, all tape around the oven and any shipping
screws securing the oven to the base pad. Open oven door and remove literature pack and oven
racks. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation
process. The trim is wrapped separately and taped to the top of the unit. Remove pedestal rails from
seperate box and set aside (30” Double Wall Ovens Only).
2
PREPARE THE OPENING
NOTE: If the cabinet does not have a solid bottom, two
braces or runners must be installed to support the weight
of the oven. For single ovens, the runners and braces
must support 200 lbs (91 kg). For double ovens, the
runners and braces must support 375 lbs. (170 kg).
NOTE: If marks, blemishes or the cutout opening are
visible above the installed oven, it may be necessary to
add wood shims under the runners and front trim until
the marks or opening are covered.
NOTE: If the cabinet does not have a front frame and
the sides are less than ¾” (1.9 cm) thick, shim both sides
equally to establish the cutout width.
ATTENTION INSTALLER:All electric wall ovens must be hard-wired (direct-wired) into an
approved junction box. A plug and receptacle is NOT permitted on these products.
Suitable
Bracing
to Support
Runners
C
L
2" x 4" (5 cm x 10 cm)
or Equivalent Runners Level
with Bottom of Cutout
and Flush with Sides of Cutout
DESIGN INFORMATION
SINGLE OVEN INSTALLATIONS
The single oven may be installed in a cabinet alone or above a warming drawer. The single oven may also
be installed below a countertop or below specified cooktops. See the label on top of the oven for approved
models.
DOUBLE OVEN INSTALLATIONS
A double oven may be installed in a cabinet alone or above a warming drawer. See the label on top of the
oven for approved models.
IMPORTANT: Always refer to individual installation instructions packed with each product for specific
requirements.
Whatsapp
Mail
Facebook
Brauchen Sie Hilfe?
Anzahl der Fragen: 0
Haben Sie eine Frage zum GE PK7500DFBB oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere GE PK7500DFBB-Eigentümer Ihre Frage richtig beantworten.
Über die GE PK7500DFBB
Sehen Sie sich hier kostenlos das Handbuch für GE PK7500DFBB an. Dieses Handbuch fällt unter die Kategorie Backöfen und wurde von 1 Personen mit einem Durchschnitt von 7.5 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Engels, Spaans. Haben Sie eine Frage zum GE PK7500DFBB oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage
Nachfolgend finden Sie die am häufigsten gestellten Fragen zu GE PK7500DFBB .
Stimmt es, dass der Lüfter eingeschaltet bleibt, wenn der Ofen ausgeschaltet wird?
Das stimmt. Der Lüfter des Kühlsystems läuft weiter, bis die Temperatur des Ofens ausreichend gesunken ist.
Was ist die Grilleinstellung an meinem Ofen?
Wenn die Grilleinstellung des Ofens verwendet wird, erwärmt sich das obere Element des Ofens. Die Grilleinstellung dient zum Grillen und um den Gerichten eine schöne dunkle Kruste zu verleihen.
Muss ich meinen GE Ofen immer vorheizen?
Für die beste Zubereitung eines Rezepts sollte der Ofen immer auf die empfohlene Temperatur vorgeheizt werden.
Wie kann ich angebranntes Fett aus meinem Ofen entfernen?
Angebranntes Fett wird am besten mit einem Backofenspray entfernt. Sprühen Sie das Innere des Ofens ein und lassen Sie das Spray etwa 30 Minuten lang einwirken. Der Ofen kann dann mit warmem Wasser gereinigt werden.
Wie reinigt man Ofengrills am besten?
Ofengrills werden am besten mit einem Scheuerschwamm und heißem Leitungswasser gereinigt.