Before beginning the installation, switch power off at the service panel and lock
the service disconnecting means to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a
tag, to the service panel.
Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight
on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,
stand or hang on the oven door.
Make sure the wall coverings, counters and cabinets around the oven can withstand the heat (up to
200°F [93.3°C]) generated by the oven.
MATERIALS YOU MAY NEED
Junction Box
Wire Nuts
Strain Relief Clamp for 1/2” Conduit
36” (91 cm) of String
TOOLS YOU MAY NEED
1/8” Drill Bit and Electric or Hand Drill
T20 Screwdriver
Phillips Screwdriver
Wire Strippers
7/16” Nut Driver (combination ovens)
1/4” Nut Driver (30” combination ovens)
1
REMOVE PACKAGING MATERIALS
Failure to remove packaging materials could result in damage to the appliance. Remove all
packing parts from oven, racks and heating elements. Remove protective film and labels on
the outer door and control panel. Also, remove plastic on trims and panel, all tape around the
oven and any shipping screws securing the oven to the base pad. Open oven door and remove
literature pack and oven racks. Remove the bottom trim from the top of the oven. It will be
installed at the end of the installation process. The trim is wrapped separately and taped to the top
of the unit. Remove pedestal rails from separate box and set aside (30” Double Wall Ovens Only).
2
PREPARE THE OPENING
NOTE: If the cabinet does not have a solid
bottom, two braces or runners must be
installed to support the weight of the oven.
For single ovens, the runners and braces
must support 220 lbs (99 kg). For double and
combination ovens, the runners and braces
must support 400 lbs. (181 kg).
NOTE: If marks, blemishes or the cutout
opening are visible above the installed oven,
it may be necessary to add wood shims
under the runners until the marks or opening
are covered.
NOTE: If the cabinet does not have a front
frame and the sides are less than ¾” (1.9 cm)
thick, shim both sides equally to establish the
cutout width.
ATTENTION INSTALLER:All electric wall ovens must be hard-wired (direct-wired)
into an approved junction box. A plug and receptacle is NOT permitted on these products.
DESIGN INFORMATION
SINGLE OVEN INSTALLATIONS
The single oven may be installed in a cabinet alone or above a warming drawer. The single oven
may also be installed side by side, below a countertop, or below specified cooktops. See the label
on top of the oven for approved models.
DOUBLE AND COMBINATION OVEN INSTALLATIONS
A double or combination oven may be installed in a cabinet alone or above a warming drawer.
See the label on top of the oven for approved models.
IMPORTANT: Always refer to individual installation instructions packed with each product for
specific requirements.
Questions? Call us at 1.800.432.2737 or visit GEAppliances.com.
In Canada, call 1.800.561.3344 or visit GEAppliances.ca.
Suitable
Bracing
to Support
Runners
2" x 4" (5 cm x 10 cm)
or Equivalent Runners Level
with Bottom of Cutout
and Flush with Sides of Cutout
C
L
Whatsapp
Mail
Facebook
Brauchen Sie Hilfe?
Anzahl der Fragen: 0
Haben Sie eine Frage zum GE Profile PTS7000SNSS oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere GE Profile PTS7000SNSS-Eigentümer Ihre Frage richtig beantworten.
Über die GE Profile PTS7000SNSS
Sehen Sie sich hier kostenlos das Handbuch für GE Profile PTS7000SNSS an. Dieses Handbuch fällt unter die Kategorie Backöfen und wurde von 2 Personen mit einem Durchschnitt von 8.9 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Engels, Spaans. Haben Sie eine Frage zum GE Profile PTS7000SNSS oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage
Nachfolgend finden Sie die am häufigsten gestellten Fragen zu GE Profile PTS7000SNSS .
Stimmt es, dass der Lüfter eingeschaltet bleibt, wenn der Ofen ausgeschaltet wird?
Das stimmt. Der Lüfter des Kühlsystems läuft weiter, bis die Temperatur des Ofens ausreichend gesunken ist.
Was ist die Grilleinstellung an meinem Ofen?
Wenn die Grilleinstellung des Ofens verwendet wird, erwärmt sich das obere Element des Ofens. Die Grilleinstellung dient zum Grillen und um den Gerichten eine schöne dunkle Kruste zu verleihen.
Muss ich meinen GE Ofen immer vorheizen?
Für die beste Zubereitung eines Rezepts sollte der Ofen immer auf die empfohlene Temperatur vorgeheizt werden.
Wie kann ich angebranntes Fett aus meinem Ofen entfernen?
Angebranntes Fett wird am besten mit einem Backofenspray entfernt. Sprühen Sie das Innere des Ofens ein und lassen Sie das Spray etwa 30 Minuten lang einwirken. Der Ofen kann dann mit warmem Wasser gereinigt werden.
Wie reinigt man Ofengrills am besten?
Ofengrills werden am besten mit einem Scheuerschwamm und heißem Leitungswasser gereinigt.