Honeywell RTH230B Bedienungsanleitung

Honeywell RTH230B
9.2 · 2
PDF Bedienungsanleitung
 · 4 Seiten
Englisch
BedienungsanleitungHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

Sehen Sie sich hier kostenlos das Handbuch für Honeywell RTH230B an. Dieses Handbuch fällt unter die Kategorie thermostate und wurde von 2 Personen mit einem Durchschnitt von 9.2 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Honeywell RTH230B oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Brauchen Sie Hilfe?

Haben Sie eine Frage zu Honeywell und steht die Antwort nicht im Handbuch?

  • Erhalten Sie Updates zu Lösungen.
  • Erhalten Sie Antworten auf Ihre Fragen

Frage und Antwort

Anzahl der Fragen: 0

Der Thermostat Honeywell RTH230B ist ein programmierbarer Raumtemperaturregler für Heizungssysteme. Er verfügt über ein klares und leicht zu lesendes Display, das die aktuelle Temperatur und die Einstellungen anzeigt. Der Thermostat hat eine programmierbare Funktion, mit der die Temperatur zu bestimmten Zeiten automatisch eingestellt wird, was eine energiesparende Lösung darstellt. Außerdem ist der Honeywell RTH230B einfach zu installieren und kann in jedem Raum des Hauses verwendet werden. Der Thermostat verfügt über eine Temperaturanzeige in Fahrenheit oder Celsius und ist mit den meisten Heizsystemen kompatibel. Beim Kauf des Thermostats ist eine Anleitung enthalten, die eine einfache Installation und Bedienung ermöglicht. Honeywell ist ein bekannter Hersteller von Thermostaten von hoher Qualität und der RTH230B ist ein zuverlässiges und langlebiges Produkt. Der Thermostat eignet sich für alle Wohnzimmer, Schlafzimmer und öffentlichen Räume, in denen eine präzise Temperaturkontrolle erforderlich ist.

Allgemeines
MarkeHoneywell
ModelRTH230B
Produktethermostat
SpracheEnglisch
DateitypBenutzerhandbuch (PDF)

Finden Sie die Antwort auf Ihre Frage nicht im Handbuch? Vielleicht finden Sie die Antwort auf Ihre Frage in den FAQs zu Honeywell RTH230B unten.

Wo sollte das Thermostat am besten platziert werden?

Am besten legen Sie das Thermostat in ein Zimmer, in dem Sie sich häufig aufhalten, in den meisten Fällen das Wohnzimmer oder die Küche. Legen Sie das Thermostat etwa eineinhalb Meter über dem Boden ab, nicht in der Sonne und nicht an einer Außenwand.

Was ist die Totzone eines Thermostats?

Wenn Ihr Thermostat eine Totzone hat, befindet sich Ihre Anlage sozusagen im Ruhezustand. Der Thermostat schaltet erst ein, wenn die Differenz beispielsweise um mehr als 2 °C von der eingestellten Raumtemperatur abweicht.

Was ist die ideale Raumtemperatur?

Die ideale Raumtemperatur liegt bei den meisten Menschen zwischen 19 und 22 Grad Celsius.

Ist das Handbuch der Honeywell RTH230B unter Deutsch verfügbar?

Leider haben wir kein Handbuch für Honeywell RTH230B in Deutsch verfügbar. Dieses Handbuch ist erhältlich in Englisch.

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Keine Ergebnisse