iFi Audio Go blu Bedienungsanleitung

iFi Audio Go blu
7.5 · 1
PDF Bedienungsanleitung
 · 1 Seite
Englisch
BedienungsanleitungiFi Audio Go blu

7. Factory Reset

System reset (long press ≥3s).

8. USB-C input

The USB-C socket isn’t just a charging port, it plays up to 24 bit
96kHz directly from USB input. It will take <40 minutes for a high-
powered USB charger to fully charge GO blu. Use the enclosed
USB 'Type A' to 'Type C' cable, smart charger or a regular charger
up to 6.3V.
Note: To switch the audio source from B luetooth to USB, please stop music playback and disconnect the GO blu from the Bluetooth source. Connect the USB-C input (8) to the U SB audio source via a USB cable and selec t the GO blu as the playback device.To switch from USB to Bluetooth transmission, disconnect the GO blu from the audio device and reconnect the Bluetooth device.The default setting of the phone does not allow charging of the GO blu (except in exclusive mode).Tip: Exclusive mode is when the device outputs only the sound of the currently used application. Only a few applications have an exclusive mode setting; in general there is no difference to charging the GO blu between turning exclusive mode on or off. However some applications allow charging with exclusive mode on.

9. LED for Battery Status

LED Status
Green* > 60%
Yellow* 10% >
Red* 10%
*Battery LED will flash when it is charging and will go out when it is fully charged.

10. Microphone

Built-in mic for hands-free calls when paired with your smartphone.
Tip: To wake up your phone's voice assistant, long-press the multi-function knob.Note: Current instructions apply to firmware version 3.05 and higher.Tip: For the required driver and all the latest firmware updates please visit our website: www.ifi-audio.com/download-hub/

ifi-audio.com

Ver1.3
Digital filters
To enter/exit filter selection mode, short-press button (1) three
times, a beep will sound, then press button (3) to select filter. See
item (4) for digital filter mode LED colours.
"STD" Standard, modest filtering, modest pre and post ringing
"MIN" Minimum phase, slow roll-off, minimum pre and post ringing

2. Multi-function knob

Controls:
- Volume control (turn)
- Play/Pause (a short click)
- Skip forward (two short clicks)
- Skip back (three short clicks)
- Wake up voice assistant (long press)
Answer the phone:
- Answer the call (short press)
- Hang up (long press)

3. Settings, Bluetooth pairing, Voice alert on/off,

Digital filter mode and restore factory settings

This button cycles between (Please refer to item 4):
Off XBass XSpace XBass + XSpace (short press) > > >
Pairing (long press ≥ 3s, indicator flashes red/blue)
Restore factory settings (press and hold for ≥ 15s, indicator
flashes white 3 times)

4. Sound effects and Bluetooth status LED

The LED colour scheme indicates the current sound effects and
Bluetooth status of GO blu.
LED Mode
Yellow XBass
Cyan XSpace
White XBass + XSpace
Off -

Bluetooth

LED Status
Off Wireless Bluetooth (Connected)
Blue (flashing) Wireless Bluetooth (Awaiting connection)
Blue/Red (flashing) Wireless Bluetooth (Pairing)
PairingFrom switch on, the GO blu will blink blue as it searches for a previously paired device. If a stored device is not found, it will automatically enter pairing mode and blink blue/red.To enter pairing mode, long-press button (3) until Bluetooth Mode LED flashes blue / red. To pair, look for ‘GO blu’ in the list of available Bluetooth devices on your phone.The GO blu is able to store up to 8 paired Bluetooth devices.

Digital filter

LED Mode
Green STD
Magenta MIN
Note: Short press the power button 3 times to enter the digital filter mode adjustment, then short press the filter mode selection button (3) to change the digital filter type. Short press the power button 3 times again to keep the current selection and exit the digital filter selection mode (it will beep). It will also exit the filter mode and retain the filter selected if no button is pressed for 30 seconds.
7
4

5 6

Specications
Chipset: Qualcomm QCC 5100 Series
Input: USB-C
TM
Bluetooth 5.1 ( AAC, SBC, aptX, aptX HD,
aptX Adaptive, aptX LL, LDAC, LHDC/HWA Codec)
Power System: Charging via USB-C, BC V1.2 compliant up to
1000mA charging current and 6.3 volts
Headphone Outputs:
Balanced: 4.4mm
UnBAL: 3.5mm
Power Output:
Balanced: 245mW @ 32Ω; 5.6V @ 600Ω
UnBAL: 165mW @ 32Ω; 2.8V @ 600Ω
Output Impedance:
Balanced: <1Ω
UnBAL: <1Ω
SNR:
Balanced: 111dBA
UnBAL: 106.5dBA
DNR: 120dB(A) (BAL/UnBAL)
THD + N:
Balanced: <0.009% (6.5mW/2.0V @ 600Ω)/
UnBAL: <0.03% (100mW/1.27V @ 16Ω)
Frequency Response: 20Hz - 45kHz (-3dB)
Battery: Lithium-polymer 450mAh approx. ~10 hours
Dimensions: 54 x 34 x 13 mm
2.1" x 1.3" x 0.5”
Net weight: 27 g (0.95 oz)
Warranty period: 12 months
*Specications are subject to change without notice.

8 9 10

1. Power on/off, Bluetooth format annunciation,

Voice alert on/off and digital filter mode on/off

Power switch
Long press and hold the power switch for ≥ 3s to power on/off the GO blu.
Bluetooth format annunciation
Press the power switch twice and the voice will announce the
Bluetooth format you are currently receiving.
Voice annunciation on/off
In the shutdown state, first press the Bluetooth pairing key (3)
without releasing it, and then press the power key to turn it on.
The operation method of turning off and turning on voice
annunciation is the same.
Note: After turning off the voice annunciation, the current Bluetooth format and sampling frequency will no longer be announced.

1 2 3

Restore factory settings

LED Status
White Restore factory settings
Note: You need to use the factory reset in the power-on state, during which no other operations can be performed; when the factory reset is successful, the white light will flash 3 times with a beep sound. After the operation is successful, the device will be in the power-on state.Warning: Restoring the factory settings will clear all the memorized Bluetooth addresses, XBass and XSpace will be turned off, and voice (decoding format) announcement will be turned on.

5. Balanced 4.4mm headphone output

Connect balanced 4.4mm headphones.

6. S-Balanced 3.5mm headphone output

Connect 3.5mm headphones.

Bedienungsanleitung

Sehen Sie sich hier kostenlos das Handbuch für iFi Audio Go blu an. Dieses Handbuch fällt unter die Kategorie Empfänger und wurde von 1 Personen mit einem Durchschnitt von 7.5 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum iFi Audio Go blu oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Inhaltsangabe

Brauchen Sie Hilfe?

Haben Sie eine Frage zum iFi Audio Go blu und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere iFi Audio Go blu-Besitzer, Ihnen eine gute Antwort zu geben.

Anzahl der Fragen: 0

iFi Audio Go blu-Spezifikationen

Nachfolgend finden Sie die Produktspezifikationen und die manuellen Spezifikationen zu iFi Audio Go blu.

Allgemeines
Marke iFi Audio
Model Go blu
Produkte Empfänger
Sprache Englisch
Dateityp Benutzerhandbuch (PDF)

Häufig gestellte Fragen

Finden Sie die Antwort auf Ihre Frage nicht im Handbuch? Vielleicht finden Sie die Antwort auf Ihre Frage in den FAQs zu iFi Audio Go blu unten.

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Keine Ergebnisse