Inno Cargo Box BRA220R Bedienungsanleitung

7.5 · 1
PDF Bedienungsanleitung
 · 2 Seiten
Englisch
BedienungsanleitungInno Cargo Box BRA220R
5411-71089G
1
2
3
5
6
8
These instructions are for the installation and use of the Inno carrier system attachment. After reading this manual, keep it in a safe place along with the
installation instructions for the rest of your carrier system.
If using an aftermarket base rack system, make sure that it is installed properly
according to the procedures described in the installation instructions for that rack.
The distance between the front and rear crossbars should be at least 60cm ( 2 feet )
Cargo Box BRA220R Installation Instructions
CAUTION
PRECAUTIONS
Do not overload your cargo box. Maximum load
capacity varies by vehicle. Check the appropriate
limits for your car in the Fit Guide and your vehicle
owner's manual and determine your maximum
loading capacity with the formula below.
The Cargo box includes the parts listed below. Verify that they are included with the
carrier you have purchased. In the event any of these is missing, contact our service
center as listed at the end of this manual.
4
7
Before driving the vehicle, shake the rack in
all directions to ensure that there is no
looseness in any of the mounting knobs and
screws. Retighten any loose knobs or screws.
Max load of
cargo box
1
10 lbs
Max load of
vehicle or
cross bar
Weight of
cargo box
OR
-
Ins
t
a
lla
tion
I
n
s
t
r
u
ctio
n
s
Use the lower of the 2 options below
Parts
Rooftop Box
QtyNO.
Knob
U-Bolt
Plate
Strap
Hole Covering
Molding
1
8
4
4
2
Strap Hook 2
2
1
2
3
4
5
6
9
10
Key
Manual Instruction
2
1
7
8
6
1
2
3
4
5
6
7
9
10
8
Temporarily put the Box on cross bars. And Insert key, turn clockwise and
push button to open the Box.
push button
key
2
Adjust the location of the Box to align with holes at A.
Rooftop Box
Cross Bar
A B
Front
Attach the Box to front cross bar with Plate, U-Bolt and Knobs. Make sure that
the ring on the Plate is on the side nearest the side of box.
U-Bolt
Ring
Plate
Cross Bar
A
Front
Ring
Plate
Cross Bar
B
Rear
U-Bolt
Tighten right and left knobs alternately to secure the Box to cross bar.
U-Bolt
Knob
Front
U-Bolt
Knobs
Rear
Make sure to tighten the right
and left knobs evenly so that
the U-bolt sits square with the
bar.
If U-bolt is not tightened
correctly, it may allow the box
to come loose.
Warning
U-Bolt
Cargo Box
Cross Bar
Front - Place plugs into the 6 unused holes to seal
Rear - Trim Molding to the proper size and insert into slot.
U-Bolt
Plug
Front
U-Bolt
Cut Molding to this size.
Molding
Rear
Thread Strap trough two Rings on each side of the box and
fasten. Attach Strap Hooks inside box lid just above Straps.
Strap Hook
Box Lid
Buckle
Strap
Buckle Ring
Push Box in all directions to make sure that there is no
loosenesss. If you notice any play in the box, retighten 8 Knobs.
10
12
11
9
Insert Key into key cylinder and turn it clockwise to "Open" position. Lift Box Lid by
pushing release button.
Release button
Box lid
1
2
Key
Leave Key in key cylinder until Box is closed to avoid locking it in the box
accidentally.
Caution
Strap
Strap Hook
Buckle
Unfasten Buckle and hang Straps on Strap Hooks to keep them out of the way while
loading. Load cargo. Unhook Straps and fasten it to secure cargo from moving while
driving.
To close lid, make sure that Key is in the OPEN position. Make sure that Hooks line
up with latches and close Box all the way.
Hook latches
Hook
Try to lift the lid at the latch points shown below to make sure that the hooks
have full engaged with the latches.
Turn Key counter clockwise to the CLOSE position.
Check at these points
Genuine Inno Replacement Parts
Specifications and the appearance of the carrier system and genuine replacement
parts are subject to change without prior notice in the interest of product
improvement.
The following genuine replacement parts are available for this Inno carrier system
component. Specify the part number when ordering parts from your dealer.
Note
M
a
n
u
a
l
I
N
N
O
ISP952 Strap
(2 pack)
ISP682 Strap Hook
(2 pack)
ISP193 Molding
(2 pack)
Key(Verify
Key number)
U-Bolt Knobs (2 pack) Plate
Instruction Manual
Fit Kit
ISP588 Hole Plugs
(4 pack)
Contact Information
If you have any questions or comments, please contact us at the service center listed below. CarMate shall not be held liable for any accidents or incidental losses arising
from improper installation or use, nor for those arising from installation or use after the customer has made any change to the system's original configuration or specifications.
Car Mate USA
383 Van Ness Ave., Suite 1603
Torrance, CA
www.innoracks.com
support@rv-inno.com

Bedienungsanleitung

Sehen Sie sich hier kostenlos das Handbuch für Inno Cargo Box BRA220R an. Dieses Handbuch fällt unter die Kategorie Nicht kategorisiert und wurde von 1 Personen mit einem Durchschnitt von 7.5 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Inno Cargo Box BRA220R oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Brauchen Sie Hilfe?

Haben Sie eine Frage zum Inno Cargo Box BRA220R und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Inno Cargo Box BRA220R-Besitzer, Ihnen eine gute Antwort zu geben.

Anzahl der Fragen: 0

Inno Cargo Box BRA220R-Spezifikationen

Nachfolgend finden Sie die Produktspezifikationen und die manuellen Spezifikationen zu Inno Cargo Box BRA220R.

Allgemeines
Marke Inno
Model Cargo Box BRA220R
Produkte Nicht kategorisiert
Sprache Englisch
Dateityp Benutzerhandbuch (PDF)

Häufig gestellte Fragen

Finden Sie die Antwort auf Ihre Frage nicht im Handbuch? Vielleicht finden Sie die Antwort auf Ihre Frage in den FAQs zu Inno Cargo Box BRA220R unten.

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Keine Ergebnisse