Name: Jammin Pro 5480002
Brand: Jammin Pro
SKU: 204250
Rating: 81 (2 reviews)

BedienungsanleitungJammin Pro 5480002

The circuitry of the British EQs is based on the technology used in the bast-known top-of-the-line consoles

and providing a warm sound without any unwanted side effects. The result are extremely musical equalizes

which, unlike simple equalizers, cause no side effects such as phase shifting or bandwidth limitation, even

with extreme gain settings of +15 dB.

All mono input channels include a 3-band equalizer. All bands provide boost or cut of up to 15 dB. In the

central position, the equalizer is inactive.

The upper (HI) and the lower band (LO) are shelving filters that increase or decrease all frequencies above

or below their cut-off frequency. The cut-off frequencies of the upper and lower band are 12 kHz and 80 Hz

respectively. The mid band (602/802/1002/1202) is configured as a peak filter with a center frequency of

2.5kHz

In addition, the mono channels are equipped with a steep LOW CUT filter

designed to eliminate unwanted low-frequenty signal components. These can be noise created by band-held

microphones, subsonic noise or plosive sounds created by highly sensitive microphones.

(slope at 18 dB/oct., -3 dB at 75 Hz)

LOW CUT

please remember that you can only use either the microphone or the line input of a

channel at any one time. You can never use both simultaneously!

TRIM

Use the TRIM control to adjust the input gain. This control should always be turned fully counterclock

-wise whenever you connect or disconnect a signal source to one of the inputs.

FX sends enable you to feed signals via a variable control from one or more channels and sum these signals

to bus. The bus appears at the console’s FX send output and can be fed from there to an external effects device.

The return from the effects unit is then brought back into the console on the aux return connectors or normal

channel inputs. Each FX send is mono and features up to +15 dB gain.

The scale has 2 different value range: the first value range (+10 to +60 dB) refers to the MIC input and

shows the amplification for the signals fed in there.

The second value range (+10 to +60 dB) refers to the line input and shows its sensitivity. The settings

for equipment with standard line-level signals (-10dB or +4dBu) look like this: While the TRIM control is

turned all the way down, connect your equipment. Set the TRIM control is turned to the external devices

standard output level. If that unit that an output signal level display, it should show 0 dB during signal

peaks. For +4 dBu, turn up TRIM sightly. for -10 dBV a bit more. Tweaking is done using the CLIP LED.

Each mono input channel offers a balanced microphone input via the XLR connector and also

features switchable +48 V phantom power supply for condenser microphones. The StudioMix preamps

provide undistorted and noised-free gain as is typically known only from costly outboard preamps.

Please mute your play back system before you active the phantom power supply to prevent

switch-on thumps being directed to your loudspeakers. Please also note the instructions in

chapter 2.4“Main section”.

MIC

Each mono input also features a balanced line input on a connector. Unbalanced devices

(mono jacks) can also be connected to these inputs.

1/4

LINE IN

3 4

1 2

+10 -40 +10 +60

TRIM

dB/dBu

BAL

UNBAL

LINE

MIC

+10 -40 +10 +60

TRIM

dB/dBu

BAL

UNBAL

LINE

MIC

MAIN OUT

CTRL ROOM OUTLINE IN 5/6

MONO

BAL

UNBAL

LINE IN 7/8

MONO

BAL

UNBAL

LINE IN9/10 LINE IN 11/12

SEND FXPHONES

- +15

L R

-15 +15

PAN

HIGH

12 KHz

MID

2.5 KHz

LOW

80 Hz

CLIP

- +15

LEVEL

- +15

L R

-15 +15

PAN

HIGH

12 KHz

MID

2.5 KHz

LOW

80 Hz

CLIP

- +15

LEVEL

- +15

L R

BAL

CLIP

- +15

5/6

LEVEL

- +15

L R

BAL

CLIP

- +15

7/8

LEVEL

- +15

L R

BAL

CLIP

- +15

9/10

LEVEL

- +15

L R

BAL

CLIP

- +15

11/12

LEVEL

-10

CD/TAPEIN OUT

- +15

MAIN MIX

MONO

BAL

UNBAL

+10 -40 +10 +60

TRIM

dB/dBu

BAL

UNBAL

LINE

MIC

+10 -40 +10 +60

TRIM

dB/dBu

BAL

UNBAL

LINE

MIC

- +15

L R

-15 +15

PAN

HIGH

12 KHz

MID

2.5 KHz

LOW

80 Hz

CLIP

- +15

LEVEL

- +15

L R

-15 +15

PAN

HIGH

12 KHz

MID

2.5 KHz

LOW

80 Hz

CLIP

- +15

LEVEL

MONO

BAL

UNBAL

FX FX FX FX

+48 V

POWER

- +15

FX SENDS

CLIP

PROGRAM

(PUSH)

REVERB 00-39

ER/DLY 40-59

MOD 60-73

PITCH 74-79

MULTI 80-99

LOW CUT

75Hz

18 dB/Oct

LOW CUT

75Hz

18 dB/Oct

LOW CUT

75Hz

18 dB/Oct

LOW CUT

75Hz

18 dB/Oct

TAPE

TO MIX

TAPE

TO CTRL

PHONES

PHANTOM

-3

-6

-10

-15

-20

CLP

24-BIT DUAL ENGINE DSP

24-BIT A/D & D/A CONVERTER

TAPE

+6. .66

MIDI sound module

Headphone

microphone

Active Speaker

CD player

Guitar

keyboard

Fig. 3.2: Live application of the StudioMix console

MD recorder

3.2 Live sound

Sehen Sie sich hier kostenlos das Handbuch für Jammin Pro 5480002 an. Dieses Handbuch fällt unter die Kategorie mischer und wurde von 2 Personen mit einem Durchschnitt von 8.1 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Jammin Pro 5480002 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Brauchen Sie Hilfe?

Haben Sie eine Frage zum Jammin Pro und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Jammin Pro -Besitzer, Ihnen eine gute Antwort zu geben.

Anzahl der Fragen: 0