PC*
Phone line behind the wall
RJ-11
connectors
PC with network
card installed
Telephone
(optional)
PA101 Phoneline10X USB adapter
Cable/ADSL
modem
*PC with FA310 Ethernet PCI card installed to interface
with the Cable or ADSL modem
START HEREThis guide provides instructions to install the Model PA101
Phoneline10X USB Adapter, using Windows
®
98.
The following six easy steps are provided in this guide for installing
your Phoneline10X USB Adapter:
1. Verify Package Contents
2. Install the Model PA101 Phoneline10X USB Adapter
3. Connect the Telephone Cables
4. Install the Network Driver
5. Install the FirstGear Software
6. Access the Network Printer
As a final step, be sure to register your NETGEAR
™
product at the
www.NETGEAR.com address.
VERIFY PACKAGE CONTENTSUnpack the package contents and verify that you have the following:
Verify PC Requirements
The instructions given in this guide are for using the Phoneline10X
USB Adapter in a PC that has Microsoft
®
Windows 98.
INSTALL THE ADAPTERTo install the Phoneline10X USB Adapter:
1. Insert the Phoneline10X USB Adapter into the USB
(universal serial bus) as shown in the illustration.
Some PCs have two USB ports.The Phoneline10X USB
Adapter can be inserted into either port.
2. Turn on power to the PC, if you have chosen to install the
adapter with the power turned off.
CONNECT THE TELEPHONE CABLESUsing the telephone cable provided in the NETGEAR package,
connect one end of the telephone cable to the port labeled
“WALL” on the adapter and the other end of the cable to an
available wall jack, as illustrated above.
Using the cable shipped with your telephone or modem, connect
that cable to the port labeled “PHONE” on the adapter.
For External Modem
If you are using an external analog modem to connect to the
Internet,refer to the following illustration that shows the connec-
tions for the wall jack, Phoneline10X USB Adapter, external
modem, and phone. Note that the captions on the USB adapter,
and modem direct you to the outlets where you connect
the cables.
For Internal Modem
The illustration below depicts the configuration with an internal
modem and shows a closeup of the connections for the wall jack,
modem adapter, Phoneline10X USB Adapter, and phone. Note that
the caption on the modem adapter and USB adapter direct you to
the outlets where you connect the cable from the wall jack and the
cable that connects to the phone.
Note: For optimal performance, the Phoneline10X USB
Adapter should be plugged directly into a wall jack,and the
modem should be plugged directly into the USB adapter.
For Cable or ADSL Modem
If you are using a cable or ADSL modem to connect to the Internet,
refer to the following illustration that shows the connections for
the wall jack, Phoneline 10X USB Adapter, and the cable/ADSL
modem. Note the captions on the USB adapter direct you to the
outlets where you connect the cables.
INSTALL THE NETWORK DRIVERThis guide provides instructions for installing the Windows
Network Driver.The steps given are for users of Windows 98.
However, because all versions of Windows 98 might not respond
the same, windows that are different from those shown in these
instructions might open but prompt you for the same information,
or windows might open in a different order than shown in these
instructions.
Note: You must install the USB adapter before installing
the network driver.You need to have the Windows 98 CD and
the NETGEAR Phoneline10X Resource CD ready to use in
the installation process.
If you have not yet named your PC and your network, before you
proceed with the installation steps, decide on a name for your
network and for each PC.You will be using these names in the
section,“Install the FirstGear Software.”
Note: If the Insert CD window opens and the “Please insert
the CD labeled Windows”message appears at any time during
the installation process, insert the Windows CD and click
OK.Then proceed with the following steps.
To install the network driver:
1. Turn on the power to the computer to start Windows 98,
if you have chosen to install the adapter with the power
turned off.
Click Next to continue.
2.
Select “Search for best driver for your device
”.
Click Next to continue.
3.
Insert the NETGEAR Phoneline10X Resource CD.
Make sure the CD Rom drive check box is selected and
click Next.
4.
Windows is now ready to load the drivers. Click Next to start
copying the drivers.
5.
Click Finish.It may take several minutes for the operating
system to complete the driver installation.
6.
Click Yes to restart the computer. If the System Settings
Change window does not open, restart your PC by using the
Start menu; select Shut down, click Restart your computer,
and then click Yes.
Brauchen Sie Hilfe?
Haben Sie eine Frage zum Netgear und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Netgear -Besitzer, Ihnen eine gute Antwort zu geben.
Anzahl der Fragen: 0