Name: Netgear PE102
Brand: Netgear
SKU: 1473167
Rating: 75 (1 reviews)

BedienungsanleitungNetgear PE102

Ethernet to Phone Line Bridge

Installation Guide

102

MODEL

START HERE

NETGEAR’s PE102 Ethernet to Phone Line Bridge seamlessly extends your high-speed Internet connection, or your existing Ethernet network, to any room in your house with a telephone jack.Using NETGEAR’s Phoneline10X products, create a home network using your existing telephone wiring without any interference to your telephone service. Home networks enable your cable modem or DSL connection to be used by multiple PCs at the same time.

PRODUCT ILLUSTRATION

PLAN YOUR TIME

The estimated setup time for this product is only 5 minutes with an existing Ethernet network.The total

time required to install the complete Phoneline10X or Ethernet network will vary, based on each devicethat you add to the network.

1.VERIFY PACKAGE CONTENTS

Make sure that your package contains the following:• PE102 Ethernet to Phone Line Bridge• Power adapter• 10-foot telephone cable• Category 5 Ethernet cable• Wall mount hardware• Installation Guide, Warranty Card and Registration Card

2.TYPICAL APPLICATION

3. PREPARE THE SITE

Before you begin installing the PE102, prepare the installation site. Make sure the site meets the oper-ating environment requirements of the equipment.Characteristic Requirement

Temperature Ambient temperature between 0 and 40ºC (32 and 104ºF).

No nearby heat sources, such as direct sunlight, warm air exhausts,or heaters.Humidity 90% maximum relative humidity, non-condensing.Ventilation Minimum 2 inches (5.08 cm) on all sides for cooling.Adequate airflow in room or wiring closet.Operating conditions At least 6 feet (1.83 m) to nearest source of electromagnetic noise (such as photocopy machine or arc welder).Service access Minimum 12 inches (19.68 cm) front and back for service access and maintenance.Front and back clearance for cables and wiring hardware,such as punchdown blocks.Power Adequate power source within 6 feet (1.83 m).Wiring hardware Wiring hardware, such as punchdown blocks or patch panels, complete before installing the PE102.

4. INSTALL THE BRIDGE

Wall Mounting (optional)1. Set the mounting screws and anchors (supplied with the wall mount hardware) in the wall.2. Using the slots on the bottom of the PE102, hang the PE102 on the wall.

3. Connect the power cord(s), first to the power entry receptacle on the PE102 rear panel, and

then to the wall.Connect the Ethernet Device to the PE102Connect the Ethernet port of the PE102 to any Ethernet device, such as a hub, switch or router.After the connection has been made and power has been applied to both devices, make sure that theLink indication is active.Share your Cable or DSL ModemYou can connect the PE102 directly to a cable or DSL modem. Combined with a RT314 Router, thiswill allow you to share your Internet connection with multiple PCs in your home.Connect your Bridge to the Telephone JackUse the supplied 10-foot telephone cable to connect the PE102 to the telephone wall jack. Connect

one end of the cable to the port labeled “To Wall”. Connect the other end of the cable to the wall jack.

If you have a telephone or a fax machine, connect either one to the port labeled “To Phone”.

5.VERIFY THE INSTALLATION

When installation is completed and power has been applied to the PE102, the following conditionsshould exist:• Power LED is on.

• Link LED at both the Ethernet port and the Phoneline10X port is on as long as another active

device is attached to each of these networks.If there are any problems, refer to the Troubleshooting table.

9624FAPE102 Ethernet to Phone Line BridgeInstallation Guide,Warranty Card, andRegistration Card10-foot telephone cableCategory 5 Ethernet cablePower adapterand cordWall mountinstallation kitEthernet to Phone Line Bridge PE102

Pwr

Link Col

100M

10M

On=Link Blinking=TransmitNormal/UplinkTo Wall To Phone

10X

Phoneline

9623FBEthernet to Phone Line Bridge PE102Power LED Phoneline10XLink LEDEthernetCollision LEDPhoneline10XTransmit LEDNormal/Uplink push buttonEthernet port with built-in LEDs

Pwr

Link

Col

100M

10M

On=Link Blinking=TransmitNormal/UplinkTo Wall To Phone

10X

Phoneline

12 V DC power adapter outletGround12Vdc 1.2A

NETGEAR, Inc.4500 Great America ParkwaySanta Clara, CA 95054 USAPhone: 1-888-NETGEARwww.NETGEAR.comSupport Information See Support Information Card for phone numbers.Internet / World Wide WebGo to http://www.NETGEAR.com for the NETGEAR Web page.Defective or damaged merchandise can be returned to your point-of-sale representative.IMPORTANT!Please register online.YOU MUST REGISTER TO OBTAIN TECHNICAL SUPPORT. PLEASERETAIN PROOF OF PURCHASE and this warranty information.To get product support, or to obtain product information and NETGEAR product documentation, direct your Web browser to the http://www.NETGEAR.com Web page.To register online, direct your Web browser to the http://www.gearguy.com/pub/registration Web page. If you do not have access to the World Wide Web, you can complete the enclosed registration card and mail it to NETGEAR customer service.October 2000

M-PE102NA-1

Ethernet to Phone Line Bridge

PE102

Pwr

Link

Col

100M

10M

On=Link Blinking=Transmit

Normal/Uplink

To Wall To Phone

10X

Phoneline

PE102 Ethernet to Phone Line BridgeTelephoneTelephone wall jackTelephone wall jackRT314 RouterCable or DSL modemInternetPA101 USB AdapterWall betweentelephone jacks

9625FA

RT314

MODEL

10/100 Mbps

Internet Access

Gateway Router

LOCAL

LNK/ACT 100

2 3 4

LNK/ACT 100 LNK/ACT 100 LNK/ACT 100

INTERNET

LNK/ACT

Ethernet to Phone Line Bridge

PE102

Pwr

Link

Col

100M

10M

On=Link Blinking=Transmit

Normal/Uplink

To Wall To Phone

10X

Phoneline

PE102 Ethernet to Phone Line BridgeFS105 Switch9626FB

512 34

Power

100M 10M

Ethernet to Phone Line Bridge

PE102

Pwr

Link

Col

100M

10M

On=Link Blinking=Transmit

Normal/Uplink

To Wall To Phone

10X

Phoneline

PE102 Ethernet to Phone Line BridgeRT314 Router9627FA12VDC

LOCAL3 2 1 INTERNETMANAGERCable or DSL modemInternet

Ethernet to Phone Line Bridge

PE102

Pwr

Link

Col

100M

10M

On=Link Blinking=Transmit

Normal/Uplink

To Wall To Phone

10X

Phoneline

PE102 Ethernet to Phone Line BridgeTelephoneTelephone wall jack9628FA

START HERE

PRODUCT ILLUSTRATION

PLAN YOUR TIME

VERIFY PACKAGE CONTENTS

TYPICAL APPLICATION

PREPARE THE SITE

INSTALL THE PE102

VERIFY THE INSTALLATION

PE102.QCard.Revise.FINAL 10/23/00 3:46 PM Page 1

Sehen Sie sich hier kostenlos das Handbuch für Netgear PE102 an. Dieses Handbuch fällt unter die Kategorie telefone und wurde von 1 Personen mit einem Durchschnitt von 7.5 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Netgear PE102 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Brauchen Sie Hilfe?

Haben Sie eine Frage zum Netgear und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Netgear -Besitzer, Ihnen eine gute Antwort zu geben.

Anzahl der Fragen: 0