Pyle PHRM36

Pyle PHRM36 Bedienungsanleitung

(1)
  • Diagram 1
    Diagram 2
    Diagram 3
    SCREW
    BACK COVER
    O Ring
    CR2032
    BATTERY
    73-242-0001
    The Pulse Sonic
    Thank you for choosing P\OH6SRUWV as your personal trainer. In order to be able to
    make the best use of this device, please read the instruction manual carefully.
    Do not discard, keep the manual for future reference.
    ThLVZDWFK requires CR2032 x 2PCS lithium batteries. Only the recommended
    batteries are to be used.
    When replacing the batteries, the following are to be strictly observed.
    1)Only adults should install and replace the batteries.
    2)DO NOT use rechargeable batteries.
    3)Exhausted batteries should be removed from the Pulse Sonic.
    Features
    · Time/Date
    · Present Heart Rate
    · Maximum Heart Rate
    · Average Heart Rate
    · Target Zone Setting
    · 1/100 sec Stopwatch
    · Calories Burnt
    · Daily Alarm
    · User Setting
    · EL Backlight
    · Energy Saving Function – Auto Display Off
    Wear the Heart Rate Belt on your chest with the sensor over your heart for detection
    of the heart rate.
    We will notice that there are two noticeably different patches on the inside of the Heart
    Rate Belt. These are the sensors for detecting your Heart Rate. Before you put the Heart
    Rate Belt, wet these two patches lightly so that the sensors can detect your heart rate
    more easily, faster and more accurately.
    Time/Date Function
    1) To set the time and date, press the “ Mode ” button till you get to the time/date function.
    2) Press and hold the “ Set ” button for 3 seconds then the year digits would start flashing.
    3) Adjust your year by pressing the “ Set ” (to count down) or “ Start / Stop ” (to count up)
    4) When the year is set, press the Mode button and the month-digits will then flash. Now
    press“ Set ” button (to count down) or “ Start / Stop ” button (to count up).
    5) When the month is set, press the Mode button and the day-digits will then flash. Now
    press“ Set ” button (to count down) or “ Start / Stop ” button (to count up).
    6) When the day of the month is set, press the Mode button and the hour-digits will then
    flash.Now press “ Set ” button (to count down) or “ Start / Stop ” button (to count up).
    7) When the hour of the day is set, press the Mode button and the minute-digits will then
    flash. Now press “ Set ” button (to count down) or “ Start / Stop ” button (to count up).
    8) When the minute of hour is set, press the Mode button and the hour-digits will then
    flash appear.
    9) When the time mode is selected, press Mode button to set the time and date. Noted
    that the day of the week is displayed at the bottom of the watch and will be
    automatically set according to the date and year selected.
    10) Press “ Set ” button to select the 24-hour or the 12-hour. The “ ” icon represent
    nighttime and the “ ” icon represent daytime.
    Note: If no changes (adjustments) are made after 1 minute, it will automatically return
    to the main display.
    Present Heart Rate
    1) Press the “ Mode ” key till you have got to the present
    heart rate function located on the main display, below the
    time/date function.
    2) Wait for the “ " to reach the heart rate watch and
    your heart rate should appear in a few seconds.
    Maximum Heart Rate Mode
    The maximum heart rate mode records your highest ever
    heart rate and if you have a even higher heart rate then your
    previous record, it will replace the old one and only the new
    will be shown on the highest heart rate mode.
    1) Press “ Mode ” till you get to the highest heart rate mode
    that is below the time/date function.
    2) Press the “ Mode ” button again till you see the word max
    next to the heart rate section like this. Then it will tell you
    your maximum heart rate.
    Average Heart Rate
    The average heart rate records your average heart rate and
    it is changed as you use it more often on average heart rate
    replacing the other as you use it more.
    1) Press the “ Mode ” key till you get to the average heart
    rate that is below the time/date function.
    2) Press the “ Mode ” button once and you ’ll see the AVG
    next to the display of heart rate.
    Then you ’ll see you average heart rate.
    Note: The heart rate ranges from the lowest of 35 and the
    maximum of 250.
    Zone Setting
    This parameter sets the intensity of your exercise, and thus
    monitors your heat rate according to your zone selection.
    You may also choose to turn the zone alarm on, in which
    case the devise will beep if your instantaneous heart rate is
    not within the target zone.
    1) First go to the Zone Setting by pressing the Mode button.
    2) The words ' - H - ' will be displayed and flashing, status of
    the zone alarm is ON.
    Press again the Set button and zone alarm will be OFF
    and the words ' - H - ' will not flash.
    3) Press and hold the Set button when the zone alarm
    is ON in order to go to the High Zone Setting mode. You will
    see the bottom range value of the BPM will appear flashing.
    Now press the Start / Stop button (to count-up) or the
    Set button (to count down).
    By pressing either the Start / Stop or the Set button once,
    the value will go up or down respectively by one unit. If
    you press and hold either the Start / Stop or the Set button,
    the value will continue counting up or down until you
    release the button. When you have come to the desired
    value for the bottom range, press the Mode button to
    confirm your High Zone setting and the bottom range value
    of the BPM will stop flashing.
    4) Press again Mode button in order to go to the Low
    Zone Setting. The words ' - L - ' will be displayed and
    flashing, status of the zone alarm is ON. Press again
    the Set button and zone alarm will be OFF and the
    words ' - L -' will not flash.
    5) Press & hold the Set button when the zone alarm is
    ON in order to go to the Low Zone Setting mode.
    You will see the bottom range value of the BPM will
    appear flashing.
    Now press the Start / Stop button (to count-up) or
    the Set button (to count down).
    By pressing either the Start / Stop or the Set button
    once, the value will go up or down respectively by one
    unit. If you press and hold either the Start / Stop or
    the Set button,the value will continue counting up or
    down until you release the button. When you have
    come to the desired value for the bottom range, press
    the Mode button to confirm your Low Zone setting and
    the bottom range value of the BPM will stop flashing.
    6) Note that the Target Zone setting of the Heart Rate
    Monitor has been defaulted High Zone with 160 BPM
    and Low Zone with 80 BPM ( Range : 35 – 250 BPM )
    Stopwatch / Calories Burnt
    1) Press the “ Mode ” key till you get to the stop watch
    function.
    2) To start the stopwatch, press the “ Start / Stop ” key.
    3) Press again the “ Start / Stop ” key to take the lap
    counting and : ” will be flashing and counting continued.
    4) To stop the stopwatch, press the “ Set ” key. Press
    Start / Stop ” key to start again the stopwatch.
    5) You can check your calories burnt by press the “ Set
    key when the stop watch is stopping or in the lap
    counting mode.
    Press “ Start / Stop ” key to go back the stop watch
    function and stop watch will start again
    Press “ Set ” key to go back to the stop watch function.
    6) To reset, press & hold the “ Set ” key and all the data
    will reset to zero.
    7) Measuring Unit : 1/100 second , Measuring
    Capacity : 23 hr 59 m 59s
    8) Calories Unit : 1 Kcal , Measuring Capacity : 19999.99
    Daily Alarm
    1) Press “ Mode ” till you get to the alarm function.
    2) To set your alarm, Press and hold the “ Set ” button for
    3 seconds and the hour digit should start flashing.
    3) Adjust your hour of the alarm by pressing the “ Set
    button (to count down) or the “ Start / Stop ” button (to
    count up).
    4) Then press the Mode ” button to set the next part of
    the setting which is the minutes.
    And once again, press either the “ Set ” button (to
    count down)or the “ Start / Stop ” button (to count up)
    5) Press the “ Mode ” button to complete the setting of
    the alarm.
    6) To activate or deactivate the alarm “ ”, press the
    Set ” button.
    User Setting / Maximum Heart Rate Record
    1) Press “ Mode ” button till you get to the User Setting
    function and you can set your Age
    Press the Start / Stop ” button (to count-up) to set
    your Age. If you press and hold the “ Start / Stop ” button,
    the value will continue counting up until you release
    the button. When you have come to the desired value,
    press the “ Set ” button to confirm your setting and enter
    next setting – Weight
    Default : 16, Range : 5 to 99
    2) Press the Start / Stop ” button (to count-up) to set
    your Weight. If you press and hold the “ Start / Stop
    button, the value will continue counting up until you
    release the button.
    When you have come to the desired value, press
    the “ Set ” button to confirm your setting and enter next
    setting – VO2max
    Default : 50kg, Range : 20 to 199kg
    3) Press the Start / Stop ” button (to count-up) to set your
    VO2max. If you press and hold the “ Start / Stop ” button,
    the value will continue counting up until you release
    the button.
    When you have come to the desired value, press the
    Set ” button to confirm your setting and enter your
    Maximum heart rate record
    Default : 40, Range : 10 to 94
    4 Press the “ Set ” button to check your Maximum heart
    rate record
    5. Press again the “ Set ” button to check the Heart Rate Ratio
    6. Press the “ Mode ” button in any time to go back to
    Time/Date Mode.
    Noted : You need to enter the USER SETTING MODE to
    configure your personal information settings before use.
    Energy Saving Function – Auto Display Off
    If the chronograph / timer is in stop state, in any non setting mode, the time reaches
    12:00am will enter Display Off mode. Press “ MODE ” key to turn on display and enter
    Time/Date mode.
    Installing the Battery
    The Heart Rate Monitor uses 2 pcs CR2032 lithium batteries .Use only the recommended
    batteries.
    Pulse Sonic
    1) The batteries compartment is located at the back of the Pulse Sonic. To install/replace
    the batteries, un-screw the back cover by screw driver. (Diagram 1)
    2) Take out the old batteries and dispose of properly.
    3) Insert the new batteries, making sure that the poles are correctly placed.
    4) Screw back the back cover.
    Heart Rate Belt
    1) Hold the Heart Rate Belt firmly. Insert a coin into the slit of the compartment lid and turn it
    clockwise. The lid should come off easily.(Remove used battery CR2032)(Diagram 2)
    2) Gently place the battery into the battery slot of the battery compartment.(Diagram 3)
    3) Put the compartment lid back into place and tighten it firmly by turning it anti-clockwise
    with the help of coin.
    IMPORTANT BATTERY INFORMATION
    Battery installation and removal should be performed by an adult
    Use only batteries recommended in this instruction sheet
    Be sure to install the batteries with the correct polarity, as indicated
    Remove all batteries when replacing
    Only batteries of the same and equivalent type as recommended are to be used
    Do not short-circuit the supply terminals
    Exhausted batteries should be removed from the product
    Non-rechargeable batteries are not to be recharges
    Rechargeable batteries are to be removed from the product before being charged
    Rechargeable batteries are only to be charged under adult supervision
    Different types of batteries or new and used batteries are not to be mixed.
    CAUTION
    Should you encounter any problems with the Pulse Sonic (e.g. malfunctioning of a
    parameter, static electricity, interferences within the product or the need to re-set the
    device), please press the reset button to reset the watch. All data previously input into
    the device shall be deleted and you can then/will need to re-set the watch all over again.
    Should this fail to correction the situation, remove the batteries and then put them back
    into the battery compartment. Then follow all the steps mentioned above in order to
    input the necessary data once more. The content of this manual is subject to change
    without further notice. Due to printing limitation, the displays shown in this manual may
    differ from the actual display. The manufacturer and its suppliers hold no responsibility
    to you or any other person for any damage expenses, lost-profits, or any other claims
    arisen by using this product. The contents of this manual may not be reproduced without
    permission of the manufacturer.
    Press The
    Reset Button
    HEALTH & FITNESS WATCH
    MODE
    SET
    EL
    START/STOP
    www.pyleaudio.com
Pyle PHRM36

Brauchen Sie Hilfe?

Anzahl der Fragen: 0

Haben Sie eine Frage zum Pyle PHRM36 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere Pyle PHRM36-Eigentümer Ihre Frage richtig beantworten.

Sehen Sie sich hier kostenlos das Handbuch für Pyle PHRM36 an. Dieses Handbuch fällt unter die Kategorie Pulsmesser und wurde von 1 Personen mit einem Durchschnitt von 9.4 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Pyle PHRM36 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Pyle PHRM36-Spezifikationen

Allgemeines
Marke Pyle
Model PHRM36
Produkte Pulsmesser
EAN 31113589731, 68889005936, 710069206120, 763615953795
Sprache Englisch
Dateityp PDF
Technische Details
Stoppuhr
Uhrmodus 12 h / 24 h
Herzfrequenzbasis Kalorienberechnung
Statistische Funktion Average, Maximum
Ausdauer
Wasserfest
Wasserdicht bis 10
Leistung
Anzahl unterstützter Batterien 1
Design
Produktfarbe Schwarz

Bedienungsanleitu.ng

Auf der Suche nach einer Bedienungsanleitung? Bedienungsanleitu.ng sorgt dafür, dass Sie in Windeseile die Bedienungsanleitung finden, die Sie suchen. In unserer Datenbank befinden sich mehr als 1 Million PDF Bedienungsanleitungen von über 10.000 Marken. Jeden Tag fügen wir die neuesten Bedienungsanleitungen hinzu, damit Sie jederzeit das Produkt finden, das Sie suchen. Es ist ganz einfach: Tippen Sie in der Suchleiste Markenname und Produkttyp ein und Sie können direkt die Bedienungsanleitung Ihrer Wahl gratis online einsehen.

Bedienungsanleitu.ng

© Copyright 2020 Bedienungsanleitu.ng. Alle Rechte vorbehalten.

Diese Website benutzen Cookies. Wenn Sie die Website weiter nutzen, stimmen Sie der Verwendung von Cookies zu.

Erfahren Sie mehr