Pyle PHRM40

Pyle PHRM40 Bedienungsanleitung

(1)
  • 73-227-0010
    Instructions Manual Heart Rate Watch One button
    Thank you for purchasing this heart rate monitor. This set of heart rate monitor consists of a
    watch and a heart rate watch. This watch was especially designed to be simplistic and user-friendly,
    based on a one-button operation. We recommend you to read the instruction manual thoroughly
    as it contains information to help you understand, maintain and get the most out of your heart rate
    monitor.
    This heart rate watch requires 1x CR2032 lithium battery. Only the recommended batteries are to
    be used.
    When replacing the batteries, the following are to be strictly observed.
    1. Only adults should install and replace the battery.
    2. DO NOT use rechargeable batteries.
    3. Exhausted batteries should be removed from the pedometer watch.
    Features:
    Time (12/24 HR)/Date/Day
    Heart Rate Measurement (Average and maximum heart rate)
    Data Storage
    Exercise (with setting of your own high/low zones)
    Mode Flow Chart Time
    Wear the Heart Rate Belt on your chest with the sensor over your heart for detection of the heart rate.
    You will notice that there are two noticeably different patches on the inside of the Heart Rate Belt.
    two patches lightly so that the sensors can detect your heart rate more easily, faster and more
    accurately.
    Time/Date/Day Mode
    Time mode is the default screen which displays the day of the week, time and date. The day of the
    week can be found at the very top of the display in the form of a dash. The screen is divided into
    half horizontally and the top is occupied by the time and am/pm can be seen if settings have been
    adjusted to 12hrs. The month and the day can be found at the bottom half of the dividend and
    below M/D indicates Month or Date.
    Time Mode Settings
    1. Press the front button until you get to a screen than displays ‘TIME’.
    2. Wait for 3 seconds to enter the mode.
    3. Then the ‘12’ will flash next to ‘HR’ for 3 seconds and ‘YES?’ will then appear for 3 seconds.
    When ‘12’ is flashing, you may press the front button to opt for a 24HR.
    4. Then wait for ‘YES?’ screen to appear and press for confirmation.
    5. The next stage of setting concerns the time and the hour’s digits will be flashing. To increment
    setting press the front button when ‘+’ is displayed. To decrement you must increment and wait
    for 3 seconds before it will alternate to ‘-‘and press the front button until your desired values. It
    will then alternate back to ‘+’ and wait for a further 3 seconds to go to the next stage of settings.
    (If no buttons are pressed for 3 seconds for the setting of the hours digits, it will automatically
    jump to the minute’s digits.)
    6. The minute’s digits will flash and when ‘+’ is on, press the front button to increment settings.
    To decrement settings, you must increment first and wait for 3 seconds before the ‘-‘ is on.
    7. To confirm your settings, ‘YES?’ will come up, press the front button and it will automatically
    return to the default screen.
    Note:
    - If the button is not pressed for 5 minutes during setting mode, it will automatically exit setting
    mode and return to the default screen.
    - At AM 12:05, the watch will automatically enter energy saving mode which will allow the
    screen to switch off.
    - To exit setting, hold the button for 3 seconds.
    Date Setting
    1. Scroll through the modes until ‘DATE’ screen appears.
    2. Wait for 3 seconds to enter the mode.
    3. The year’s digits will be flashing, to increment settings, press the front button. To decrement,
    you must increment first and then wait for 3 seconds before it jumps to the ‘-‘ icon.
    4. To confirm, wait for 3 seconds and the month’s digits will flash.
    5. To increment settings, press the front button. To decrement, you must increment first and then
    wait for 3 seconds before it jumps to the ‘-‘ icon.
    6. To confirm, wait for 3 seconds and the date’s digits will flash.
    7. To increment settings, press the front button. To decrement, you must increment first and then
    wait for 3 seconds before it jumps to the ‘-‘ icon.
    8. To confirm, wait for 3 seconds and a ‘YES?’ screen will appear, press the front button for
    confirmation.
    Data Storage
    1. Scroll through the modes until a screen that displays ‘DATA appear.
    2. Wait for 3 seconds to enter the mode.
    3. It will display the total exercise time as well as your average heart rate.
    4. To see your maximum heart rate press the front button.
    5. Press the front button again and it will display the time, month and day in which the exercise
    session started.
    6. Press again to exit.
    Heart Rate Measurement
    1. Scroll through the modes until a screen with ‘HRM’ appears.
    2. Wait for 3 seconds to enter the mode.
    3. The timer will automatically start, to stop the timer, press the front button and the display will
    read ‘STOP’.
    4. Below the timer, heart rate is constantly measured and it will be recorded in data storage.
    5. Press the front button again and it will automatically return to the default screen.
    Setting Exercising Zone
    1. Scroll through the modes until a screen with ‘ZONE’ appears.
    2. Wait for 3 seconds to enter the mode.
    3. The screen will automatically display ‘BEEP’ and the ‘OFF’ will be flashing. To enable the beep,
    press the front button to alternate between enabling/disabling.
    4. Wait for 3 seconds and ‘YES?’ will be on screen, press the front button for confirmation.
    5. The next step is to set the high zone, to increment the figure, press the front button. To decrement,
    you must increment first ‘+’ and wait for 3 seconds before the ‘-‘ decrement icon will be on.
    6. Wait for 3 seconds and ‘YES?’ will be on screen for your confirmation, press the front button to
    confirm.
    7. Again, repeat step 5 for setting the low zone. To increment the low zone, press the front button
    until your desired mode and wait 3 seconds for confirmation. If you wish to decrement, you must
    increment first and wait for 3 seconds before decrementing.
    8. Wait for 3 seconds when you have reached your desired value and ‘YES?’ will be on screen, press
    the front button for confirmation.
    9. It will automatically return to default screen after confirmation.
    Heart Rate Monitor
    The Heart Rate Watch requires 1 x CR 2032 lithium battery. Use only
    recommended battery.
    1.Hold the watch firmly. Insert a coin into the slit of the compartment lid and turn it
    anti-clockwise. The lid should come off easily. ( Diagram 1-a )
    2.Remove used battery CR2032 by pull out the metal plate and place the new
    battery into the battery slot of the battery compartment. ( Diagram 1-b )
    3.Put the compartment lid back into place and tighten it firmly by turning it
    clockwise with the help of coin.
    Installing the Battery
    Heart Rate Belt
    1. Hold the Heart Rate Belt firmly. Insert a coin into the slit of the compartment lid and turn it
    clockwise.The lid should come off easily. (Remove used battery CR2032) (Diagram 2)
    2. Gently place the battery into the battery slot of the battery compartment. (Diagram3)
    3. Put the compartment lid back into place and tighten it firmly by turning it anti-clockwise with
    the help of coin.
    Note:
    - Non-chargeable battery is not to be recharged.
    - Different types of batteries or new and used batteries are not to be mixed.
    - The supply terminals are not to be short-circuited.
    - Batteries are to be inserted with the correct polarity.
    - Exhausted batteries are to be removed from the unit.
    Caution
    Should you encounter any problems with the heart rate watch (e.g. malfunctioning or the need to
    re-set the device), remove the back lid and press the “RESET” button which is located on the
    circuit board at exactly 90 degrees on the left. If on the rare occasion, the watch remains incapable
    of operating normally, remove the batteries and then put it back into the battery compartment.
    Turn on the device by pressing the button and operate as normal when all settings have been restored.
    - The content of this manual is subject to change without further notice.
    - Due to printing limitation, the displays shows in this manual may differ from the actual display.
    - The manufacturer and its suppliers holds no responsibility to you or any other person for any
    damage expenses, lost-profits, or any claim arose by using this product.
    - The contents of this manual may not be reproduced without permission of the manufacturer.
    Diagram 2 Diagram 3
    MODE/START/STOP/SET
    SU TU WE TH FR SAMO
    HEART RATE BELT
    setting
    setting
    DATE
    Diagram 1- a Diagram 1- b
    PHRM40
    www.pyleaudio.com
Pyle PHRM40

Brauchen Sie Hilfe?

Anzahl der Fragen: 0

Haben Sie eine Frage zum Pyle PHRM40 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere Pyle PHRM40-Eigentümer Ihre Frage richtig beantworten.

Sehen Sie sich hier kostenlos das Handbuch für Pyle PHRM40 an. Dieses Handbuch fällt unter die Kategorie Pulsmesser und wurde von 1 Personen mit einem Durchschnitt von 9.4 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Pyle PHRM40 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Pyle PHRM40-Spezifikationen

Allgemeines
Marke Pyle
Model PHRM40
Produkte Pulsmesser
EAN 151903076989, 41114608386, 68889005950, 763615953818
Sprache Englisch
Dateityp PDF
Technische Details
Stoppuhr
Uhrmodus 12 h / 24 h
Statistische Funktion Average, Maximum
Uhrfunktion
Bildschirm
Eingebaute Anzeige
Design
Produktfarbe Schwarz

Häufig gestellte Fragen

Nachfolgend finden Sie die am häufigsten gestellten Fragen zu Pyle PHRM40 .

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Bedienungsanleitu.ng

Auf der Suche nach einer Bedienungsanleitung? Bedienungsanleitu.ng sorgt dafür, dass Sie in Windeseile die Bedienungsanleitung finden, die Sie suchen. In unserer Datenbank befinden sich mehr als 1 Million PDF Bedienungsanleitungen von über 10.000 Marken. Jeden Tag fügen wir die neuesten Bedienungsanleitungen hinzu, damit Sie jederzeit das Produkt finden, das Sie suchen. Es ist ganz einfach: Tippen Sie in der Suchleiste Markenname und Produkttyp ein und Sie können direkt die Bedienungsanleitung Ihrer Wahl gratis online einsehen.

Bedienungsanleitu.ng

© Copyright 2020 Bedienungsanleitu.ng. Alle Rechte vorbehalten.

Diese Website benutzen Cookies. Wenn Sie die Website weiter nutzen, stimmen Sie der Verwendung von Cookies zu.

Erfahren Sie mehr