RCA RCR313BR

RCA RCR313BR Bedienungsanleitung

(1)
  • FCC Statement:
    This device complies with part 15 of the FCC Rules. Operation is subject
    to the following two conditions: (1) This device may not cause harmful
    interference, and (2) this device must accept any interference received,
    including interference that may cause undesired operation.
    Note: This equipment has been tested and found to comply with the
    limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
    These limits are designed to provide reasonable protection against
    harmful interference in a residential installation. This equipment
    generates, uses and can radiate radio frequency energy and, if not
    installed and used in accordance with the instructions, may cause
    harmful interference to radio communications. However, there is no
    guarantee that interference will not occur in a particular installation. If
    this equipment does cause harmful interference to radio or television
    reception, which can be determined by turning the equipment off and
    on, the user is encouraged to try to correct the interference by one or
    more of the following measures:
    Reorient or relocate the receiving antenna.
    Increase the separation between the equipment and receiver.
    Connect the equipment into an outlet on a circuit different from that
    to which the receiver is connected.
    Consult the dealer or an experienced radio/TV technician for help.
    Caution: Any Changes or modifi cations not expressly approved by the
    party responsible for compliance could void the user’s authority to
    operate this equipment.
    Industry Canada Regulatory Information
    This class B digital apparatus complies with Canadian ICES-003
    Avis d’Industrie Canada
    Cet appareil numérique de la classe B est conforme a la nome
    NMB-003du Canada
    There is a possibility that a programmed code may only be
    able to control some of your device features (for example,
    only turns a device on and off). To confi rm that the device
    key is programmed with the correct code for maximum
    functionality, test the device. Attempt to control a variety
    of the device’s functions with the remote. If some of the
    features of your devices don’t work, try programming the
    remote with a different code in the list using the Direct Code
    Entry Method, until you fi nd the code that allows the remote
    to control the majority of your device’s functions. Different
    codes can provide different levels of functionality.
    Problem: The POWER key does not light when you press a
    key.
    You may have pressed an invalid key for the mode the
    remote is in.
    Make sure the remote is in the correct mode by pressing
    the corresponding device key (TV, SAT•CBL•STREAM,
    DVD•VCR). This tells the remote which device to operate.
    Make sure the batteries are fresh and are properly installed.
    Replace the batteries with two new AA batteries, if necessary
    (see the Battery Installation section).
    Problem: The remote will not change channels on device.
    Make sure the remote is in the correct mode by pressing
    the corresponding device key (TV, SAT•CBL•STREAM,
    DVD•VCR). This tells the remote which device to operate.
    Press the OK key after you enter a channel number.
    Remove any obstacles between the remote and the device.
    Make sure to aim the remote at the IR sensor on the device.
    Problem: The device’s menu does not appear on the TV
    screen.
    Make sure you have connected the device to your TV properly
    and selected the correct input. (See your devices’ Owners
    Manuals for proper connection procedures.)
    Make sure the remote is in the correct mode by pressing
    the corresponding device key (TV, SAT•CBL•STREAM,
    DVD•VCR). This tells the remote which device to operate.
    Menu access isn’t supported for all brands. You may need to
    use your original remote control to access menu functions
    for some devices.
    For more information, please visit
    www.RCAAudioVideo.com
    Consumer Help Line: 1-800-420-7968
    In most cases, the keys
    on this remote perform
    the same functions
    as the keys on your
    original remotes once
    you’ve programmed this
    remote to operate your
    components. Many keys
    on this remote have other
    functions as well.
    Illuminated
    POWER key
    serves as an indicator
    light to provide feedback.
    Device keys (TV,
    SAT•CBL•
    STREAM,
    DVD•VCR) put the remote
    in the right mode to
    control your device.
    LIGHT key ( ) turns
    backlighting on/off.
    GUIDE/HOME and MENU
    access the same features
    as the keys on your
    original remotes.
    Arrow keys act as
    navigation keys for
    streaming media players
    as well as in menu and
    guide systems for other
    devices.
    Battery Saver
    Your universal remote control saves battery power by
    automatically turning off if any key is pressed for more than
    60 seconds. This saves your battery life should your remote
    get stuck in a place where the keys remain depressed, such
    as between sofa cushions.
    Congratulations on your purchase of this 3-device RCA
    Universal Remote Control. This remote features a library
    of codes with the latest devices of all major brands, with
    support for streaming media players as well. The navigation
    keys have been redesigned to function seamlessly with the
    more sophisticated menu and guide systems found in today’s
    home entertainment devices.
    Universal Remote Control
    Owner’s Manual
    RCR314WR / RCR313BR
    Manual del Propietario (parte posterior)
    Care and Maintenance
    Keep the remote dry. If it gets wet, wipe it dry
    immediately.
    Use and store the remote only in normal temperature
    environments.
    Handle the remote gently and carefully. Don’t drop it.
    Keep the remote away from dust and dirt.
    Wipe the remote with a damp cloth occasionally to keep it
    looking new.
    Modifying or tampering with the remotes internal devices
    can cause malfunction and invalidate its warranty.
    SAVE THIS MANUAL AND THE CODE LISTS!
    Remote controls can sometimes lose their programming when
    you change the batteries. Make sure you keep the manual and
    code lists in a safe place so that you can reprogram the remote
    if you need to.
    Your universal remote requires two AA alkaline batteries
    (batteries may or may not be included, depending on model).
    To install the batteries:
    1. Remove the battery compartment
    cover.
    2. Insert the batteries, matching the
    batteries to the (+) and (–) marks
    inside the battery compartment.
    3. Push the battery cover back into
    place.
    Battery Precautions:
    • Do not mix old and new batteries.
    • Do not mix alkaline, standard (carbon-zinc) or
    rechargeable (nickel-cadmium) batteries.
    • Always remove old, weak or worn-out batteries promptly
    and recycle or dispose of them in accordance with Local
    and National Regulations.
    To use this universal remote with your home entertainment
    system, fi rst you need to program it to control your devices.
    There are four ways you can program the universal remote
    to operate your devices. Try them in the order listed here:
    The Brand Code Search searches through the codes
    for select brands of devices.
    The Direct Code Entry lets you enter a code from the
    accompanying code list for your brand of device.
    The Auto Code Search goes automatically through all
    the codes for the device you’re trying to control.
    The Manual Code Search lets you manually go
    through all the codes for the device you’re trying to
    control.
    Testing the Code for Maximum Functionality
    1. Try a variety of the device’s functions with the remote.
    If some device features don’t work, go to the next step
    to try a different code.
    2. Repeat the Brand Code Search from the beginning.
    When the device turns off for the fi rst time, don’t
    press the STOP key, which would store the same code.
    Instead, with the unit now off, continue to press the
    POWER key repeatedly until the unit turns back on.
    3. Once the unit turns back on, you have found another
    code that operates the device. Press the STOP key.
    4. Test the key’s functionality again by attempting to
    control a variety of the device’s functions. If the code
    that has been stored controls the majority of the
    device’s functions, programming is complete. If the
    code stored does not give maximum functionality, try
    another code.
    Brand Code Search
    The Brand Code Search goes through only the codes for one
    of the select brands listed in the accompanying code list. If
    your brand of device is listed, this search can be very quick
    and easy.
    TIPS: Each device key is associated with a type of device—
    the TV is preset to search for TVs, SAT•CBL•STREAM for
    satellite receivers, cable boxes, digital TV converters, or
    streaming media players and DVD•VCR for VCRs or DVD
    players.
    The POWER key serves as an indicator light during
    programming, giving you feedback at each stage of the
    process.
    To exit without saving a new code at any point in the Brand
    Code Search, press the
    GO BACK key.
    1. Manually turn on the device
    you want to control.
    4. Press and hold the device key you want to program.
    While you’re holding down the device key, use your
    other hand to press and hold the remote’s
    POWER key
    at the same time.
    5. Wait until the POWER key comes on and stays on.
    Then release both keys.
    7. Point the remote directly at the
    front panel of the device you want
    to control. Press POWER on the
    remote and wait 2 seconds. The
    remote is testing a single code for
    your device’s brand.
    Did your device turn off?
    YES: Press the STOP key to store the code. You’re
    done! You’ve programmed this device key.
    NO: Press
    POWER again. The remote tests the next
    code for your brand.
    Keep pressing
    POWER every 2 seconds until your
    device turns off. When it does, press STOP.
    3. Find your device’s brand in the
    Brand Code list section of the
    accompanying code list. Circle
    the number for your brand and
    keep the list handy.
    Code Lists
    Brand Codes are used for programming using the Brand Code Search
    and Entry method outlined in the User’s Guide.
    Lista de Códigos
    Los códigos de las marcas son utilizados para programar utilizando
    los métodos de búsqueda y entrada de códigos de marcas, resaltado
    en la guía del usuario.
    0123456789
    RCA
    GE
    PROSCAN
    Insignia
    JVC
    Magnavox
    Philips
    Panasonic Samsung Sharp Sony Toshiba Vizio
    TV
    VCR
    0123456789
    RCA
    GE
    PROSCAN
    Apex JVC
    Magnavox
    Philips
    Panasonic Pioneer Samsung Sharp Sony Toshiba
    DVD
    SAT/CABLE
    0123456789
    RCA
    GE
    PROSCAN
    Motorola DirecTV
    Dish Network
    Systems/
    Echos
    tar
    General
    Instruments
    Hughes
    Network
    Systems
    Scientific
    Atlanta
    Magnavox
    Philips
    AMNIO
    ADB
    Panasonic
    Brand Code List/Lista de Códigos de Marcas
    0123456789
    Samsung
    Magnavox
    Philips
    Mitsubishi Panasonic Sharp Sony Toshiba
    RCA
    GE
    PROSCAN
    JVC
    Symphonic
    Admiral .................................
    Advent ...........................................
    Aiko .........................................................
    Akai .............................10812, 11675, 10060,
    Albatron
    ....................................................................
    America Action ..........................................................
    Anam
    ........................................................................
    AOC ........................................................................
    Apex Digital
    ........................................10156, 107
    Audiovox ...............................10451, 10180, 100
    .............................................................10875, 1
    Aventura .........................................................
    Axion
    .............................................................
    Bell & Howell ..............................................
    BenQ .........................................................
    Bradford
    ..................................................
    Broksonic ...............................................
    Candle ..................................................
    Carnivale ............................................
    Carver
    ...............................................
    Celera .............................................
    Changhong ...................................
    Citizen .........................................
    Clarion
    .......................................
    Commercial Solutions ............
    Concerto ...............................
    Contec ..................................
    Craig ...................................
    Crosley .............................
    Crown ............................
    Curtis Mathes ..............
    ....................................
    ...................................
    CXC ..........................
    Cytron ...................
    Daewoo ..............
    Dell ....................
    Denon ..............
    Diamond Visio
    Dumont ........
    Durabrand .
    Dwin
    .........
    Dynex .....
    Electrogr
    Electroh
    Emerso
    .........
    Empr
    Env
    ESA
    Fi
    F
    6. Look at the number you circled for
    your device’s brand code number.
    Press that number on the remote
    keypad.
    NOTES
    Throughout the programming of each key, be sure to
    keep the remote pointed at the IR sensor of the device
    you are currently programming the remote to control.
    Test the remote with the device to make sure the
    device key is programmed with the correct code for
    maximum functionality. If some features don’t work, try
    a different code. See the “Testing the Code for Maximum
    Functionality” section below for more information.
    During the Brand Code Search, the remote ignores
    keypresses that aren’t part of the search.
    The search times out after two minutes (the
    POWER key
    blinks four times and turns off, and the last programmed
    code under that device key is retained).
    The
    POWER key blinks four times and turns off when the
    remote has gone through all the codes. The remote exits
    the Brand Code Search. If your device hasn’t turned off
    yet, try a different search method.
    Direct Code Entry
    Direct Code Entry lets you enter a code from the
    accompanying code list for your brand of device. It’s not as
    easy as the other methods, but it’s potentially the fastest
    method.
    1. Manually turn on the device you
    want to control.
    3. Press and hold the device key you want to program
    (the POWER key comes on).
    While you’re holding down the device key, use your
    other hand enter the fi rst ve-digit code for your brand
    in the code list (the POWER key goes off after the fi rst
    digit).
    2. Find the Code List that came with
    the remote. Locate the section for
    the type of device you’re trying to
    program, and fi nd your brand in
    that section. Circle the codes for
    your brand and keep them handy.
    Code Lists
    Brand Codes are used for programming using the Brand Code Search
    and Entry method outlined in the User’s Guide.
    Lista de Códigos
    Los códigos de las m
    a
    rcas son utilizados para programar utilizando
    los métodos de búsqueda y entrada de códigos de marcas, resaltado
    en la guía del usuario.
    0123456789
    RCA
    GE
    PROS
    CAN
    Insignia
    JVC
    Magnavox
    Phi
    lips
    Panasonic Samsung Sharp S
    ony Toshiba Viz
    io
    TV
    VCR
    0123456789
    RCA
    GE
    PROSCAN
    Apex J
    VC
    Magnavox
    Phil
    ips
    Panasonic Pioneer Sa
    msung Sharp Sony Toshib
    a
    DVD
    SAT/CABLE
    0123456789
    RCA
    GE
    PROSCAN
    Motorola DirecTV
    Dish Network
    Systems/
    Echostar
    General
    Instruments
    Hughes
    Network
    Systems
    Scientific
    Atlan
    t
    a
    Magnavox
    Philips
    AMNIO
    ADB
    Panasonic
    Brand Code List/Lista de Códigos de Marcas
    0123456789
    Samsung
    Magnavo
    x
    Philips
    Mitsubish
    i Panasonic Sharp Sony Toshiba
    RCA
    GE
    PROSCAN
    JVC
    S
    ymphonic
    Admiral .................................
    Advent ...........................................
    Aiko .........................................................
    Akai .............................10812, 11675, 10060,
    Albatron
    ....................................................................
    Americ
    a Action ..........................................................
    Anam
    ........................................................................
    AOC ........................................................................
    Apex Digital
    ........................................10156, 107
    Audiovox ...............................10451, 10180, 10
    .............................................................10875, 1
    Aventura .........................................................
    Axion
    .............................................................
    Bell & Howell ..............................................
    BenQ .........................................................
    Bradford
    ..................................................
    Broksonic ...............................................
    Candle ...........................
    .......................
    Carnivale ............................................
    Carver
    ...........................
    ....................
    Celera .............................................
    Ch
    anghong ...................................
    Citizen .........................................
    Clarion
    .......................................
    Commercial Solutions ............
    Concerto ...............................
    Contec .................................
    Craig ...................................
    Crosley .............................
    Cro
    w
    n ............................
    Curtis Mathe
    s ..............
    ....................................
    ...................................
    CXC ..........................
    Cytron ...................
    Daew
    o
    o ..............
    Dell ....................
    Denon ..............
    Diamon
    d Visio
    Dumont ........
    Durabrand .
    Dwin
    .........
    Dynex .....
    Electrogr
    Electroh
    Eme
    rso
    .........
    Empr
    Env
    ESA
    Fi
    F
    NOTES
    Remember to enter the code for future reference in the
    box provided in the Code Retrieval section of this manual.
    If your brand isn’t listed in the code list, use one of the
    Code Search methods to program the remote control.
    (Refer to the Auto and Manual Code Search methods.)
    If you release the device key any time during the Direct
    Code Entry procedure, the
    POWER key blinks four times,
    and the process is exited. The last programmed code
    under the device key is retained.
    Test the remote with the device to make sure the device
    key is programmed with the correct code for maximum
    functionality. If some features don’t work, try a different
    code in the list.
    4. When you’ve fi nished entering the fi ve-digit code, keep
    holding down the device key and look at the POWER
    key.
    Is the POWER key on?
    YES: You’re done! You’ve programmed this device key.
    NO, it blinked four times and turned off: You have
    either entered a code number that is not in the code lists
    or missed a step in the code entry procedure. Try step 3
    again.
    1. Manually turn on the device you
    want to control.
    2. If you’re programming the TV or
    SAT•CBL•STREAM key, go to step 3.
    If you’re programming the
    DVD•VCR key, you need
    to tell the remote which kind of device you want this
    key to control, VCR or DVD.
    Press and hold the
    DVD•VCR key. While you’re holding
    down the DVD•VCR key, use your other hand to press
    the number key for the type of device you want to
    control with this key: 2 for VCR, 3 for DVD.
    4. Wait until the POWER key comes on and stays on.
    Then release both keys.
    5. Point the remote directly at the front panel of the device
    you want to control. Press POWER on the remote and
    wait 2 seconds. The remote is testing a single code for
    your device.
    Did your device turn off?
    YES: Press the STOP key to store
    the code. You’re done! You’ve
    programmed this device key.
    NO: Press
    POWER again. The
    remote tests the next code for
    your device.
    Keep pressing POWER every 2
    seconds until your device turns off.
    When it does, press STOP.
    TIP: Because there are so many codes, you may have to
    press the POWER key many times—possibly hundreds of
    times.
    NOTES
    Throughout the programming of each key, keep the
    remote pointed at the IR sensor of the device you are
    programming the remote to control.
    Test the remote with the device to make sure the
    device key is programmed with the correct code for
    maximum functionality. If some features don’t work, try
    a different code. See the “Testing the Code for Maximum
    Functionality” section below for more information.
    During the Manual Code Search, the remote ignores
    keypresses that aren’t part of the search.
    The search times out after two minutes (the
    POWER key
    blinks four times and turns off, and the last programmed
    code under that device key is retained).
    The
    POWER key blinks four times and turns off when the
    remote has gone through all the codes. The remote exits
    the Manual Code Search. If your device hasn’t turned off
    yet, try a different search method.
    Testing the Code for Maximum Functionality
    1. Try a variety of the device’s functions with the remote.
    If some features of your devices don’t work, go to the
    next step to try a different code.
    2. Repeat the Manual Code Search from the beginning.
    When the device turns off for the fi rst time, don’t
    press the STOP key, which would store the same code.
    Instead, with the unit now off, continue to press the
    POWER
    key repeatedly until the unit turns back on.
    3. Once the unit turns back on, you have found another
    code that operates the device. Press the STOP key.
    4. Test the key’s functionality again by trying a variety
    of functions. If the code controls the majority of the
    device’s functions, programming is complete. If the
    code stored does not give maximum functionality, try
    another code.
    Code Retrieval
    Once you’ve programmed the remote to control your
    devices, you may want to record the codes for future
    reference. If you used the Direct Code Entry method, this
    is easy. Just fi nd the codes you entered and make a note
    of them in the boxes below. If you used one of the Code
    Search methods to program your remote or if you used the
    Direct Entry method but don’t remember the code, you will
    need to retrieve each device’s fi ve-digit code. Retrieving
    the actual code and writing it down will save you time
    if you ever need to program the remote again (e.g., if
    programming is lost when you change the batteries). If the
    codes are recorded, you can use the Direct Entry method
    to reprogram your remote to control your devices, which is
    quick and easy.
    1. Press and hold the device
    key (TV, SAT•CBL•
    STREAM,
    DVD•VCR) whose code you
    wish to retrieve. The POWER
    key turns on. Keep pressing
    the device key.
    IMPORTANT
    Because this remote controls more than one device,
    you must fi rst “tell” the remote which device you wish
    to operate. That means, if you wish to operate your TV,
    you must fi rst press the TV key to put the remote in the
    TV Mode. The remote stays in that device mode until
    you press a different device key. For example, if your
    remote is in TV Mode and you want to operate the DVD
    player, you must press the DVD•VCR
    key to change
    device modes.
    Problem: The remote does not operate your device.
    Make sure the remote is in the correct mode by pressing
    the corresponding device key (TV, SAT•CBL•STREAM,
    DVD•VCR). This tells the remote which device to operate.
    Remove any obstacles between the remote and the device.
    Make sure you’re aiming the remote at the devices IR
    sensor.
    Make sure the batteries are fresh and are properly installed.
    Replace the batteries with two new AA batteries, if necessary
    (see the Battery Installation section).
    Problem: The remote can’t be programmed to operate
    your device.
    If you are testing the remote while programming it, you may
    be too far away from the device or at a wrong angle. There
    must be an unobstructed path between the remote and the
    IR sensor on the device. Move closer and make sure you
    point the remote at the device you’re trying to control.
    If you’re using the Direct Entry programming method
    to enter the codes for your brand and the unit is still not
    functioning properly, try the auto, brand, or manual search
    method.
    To control combo units, like TV/VCRs or TV/DVDs, you must
    program the individual corresponding device keys to control
    each part of the combo unit. Once programmed successfully,
    the TV key controls the TV functions, and the
    DVD•VCR key
    controls the VCR or DVD functions.
    Make sure the batteries are fresh and are properly installed.
    Problem: The remote doesn’t perform commands properly.
    Make sure the remote is in the correct mode by pressing
    the corresponding device key (TV, SAT•CBL•
    STREAM,
    DVD•VCR). This tells the remote which device to operate.
    Make sure device is ready (for example, the DVD player has
    a disc loaded).
    You may have pressed an invalid key for the mode the remote is
    in.
    If you’re trying to enter a channel number directly, try
    pressing the OK key after entering the channel number as
    this is a requirement of certain models and brands.
    VOXX Accessories Corporation (the “Company”) warrants to you the
    original retail purchaser of this product that should it, under normal use
    and conditions, be proven defective in material or workmanship during
    its lifetime while you own it, such defect(s) will be repaired or replaced
    (at the Company’s option) without charge for parts and repair labor.
    To obtain repair or replacement within the terms of this Warranty, the
    product is to be delivered with proof of warranty coverage (e.g. dated bill
    of sale), specifi cation of defect(s), transportation prepaid, to the Company
    at the address shown below.
    This Warranty does not cover product purchased, serviced or used
    outside the United States or Canada. This Warranty is not transferable
    and does not extend to costs incurred for installation, removal or
    reinstallation of the product. This Warranty does not apply if in the
    Company’s opinion, the product has been damaged through alteration,
    improper installation, mishandling, misuse, neglect, accident, or the
    simultaneous use of different battery types (e.g. alkaline, standard or
    rechargeable).
    THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY
    IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE
    AND, IN NO EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE
    PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
    This Warranty is in lieu of all other express warranties or liabilities. ANY
    IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
    MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL
    BE LIMITED TO DURATION OF THIS WARRANTY. IN NO CASE SHALL
    THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
    DAMAGES WHATSOEVER. No person or representative is authorized
    to assume for the Company any liability other than expressed herein in
    connection with the sale of this product.
    Some states/provinces do not allow limitations on how long an implied
    warranty lasts or the exclusion or limitation of incidental or consequential
    damage so the above limitations or exclusions may not apply to you.
    This Warranty gives you specifi c legal rights and you may also have
    other rights, which vary from state/province to state/province.
    U.S.A.: Audiovox Return Center, 150 Marcus Blvd., Hauppauge, New
    York 1 1788
    CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road,
    Unit 3, Door 16, Mississauga, Ontario L5T 3A5
    Trademark(s) ® Registered
    RCR314WR US 04
    ©2013 Voxx Accessories Corp.
    3502 Woodview Trace, Suite 220
    Indianapolis, IN 46268
    Step 1: Install your batteries
    Step 2: Program your remote
    Tour of the Remote
    Advanced Functions
    Troubleshooting
    Limited Lifetime Warranty
    POWER key
    2. If you’re programming the TV or
    SAT•CBL•STREAM key, go to step 3.
    If you’re programming the
    DVD•VCR key, you need
    to tell the remote which kind of device you want this
    key to control, VCR or DVD.
    Press and hold the
    DVD•VCR key. While you’re holding
    down the DVD•VCR key, use your other hand to press
    the number key for the type of device you want to
    control with this key: 2 for VCR, 3 for DVD.
    3. Press and hold the device key you want to program.
    While you’re holding down the device key, use your
    other hand to press and hold the remote’s POWER key
    at the same time.
    Note: All TV codes begin with the number 1; all VCR
    and DVR codes begin with the number 2; all DVDs,
    the number 3; and all satellite receivers, cable boxes,
    streaming players, and DTV converters, the number 5.
    5. Repeat step 4 until you have retrieved all fi ve numbers
    in the code. After the fi fth number is retrieved, the
    POWER key blinks briefl y, then turns off.
    TIP: To exit the Code Retrieval Mode at any time, press
    the GO BACK key.
    Note: If you press an invalid key during the Code
    Retrieval process, the remote will not respond. If
    you do not press a valid Code Retrieval key (TV,
    SAT•CBL•
    STREAM, DVD•VCR, INFO-OPTIONS, GO BACK),
    Code Retrieval times out after 15 seconds. The POWER
    key blinks four times, and then turns off.
    CHAN and VOL keys act as channel and volume controllers.
    The CHAN keys also provide skip forward and skip back
    control for DVD players and DVRs that support this
    functionality.
    GO BACK exits remote programming; it also performs the
    same functions as on your original remotes.
    The INPUT and — (dash) key has three functions: (1) it
    toggles through all the video sources connected to your TV;
    (2) when the remote is in VCR mode, this button toggles
    between VCR and the TV input; (3) when you’re entering
    digital channel numbers directly, this button lets you
    separate the main channel number from the sub-channel
    number (such as 59.1).
    Backlighting
    Backlight illumination helps you see the remote control
    keys better in the dark. You can turn backlight illumination
    on or off by pressing the
    LIGHT key ( ). Backlighting
    stays on as long as keys are being pressed and turns off six
    seconds after the last keypress. Once the backlight time has
    timed out, any keypress will reactivate it. If the backlight
    illumination is on, and you press the backlight key, the
    backlight turns off.
    2. While holding the device key down, press and hold the
    INFO-OPTIONS key. The POWER key turns off. After
    holding down both keys for three seconds, the
    POWER
    key turns back on.
    3. Release both keys. The
    POWER key remains on.
    4. Starting with the number 1 key, press and release each
    number key on the keypad in the following order: 1-9,
    then 0. The number that causes the
    POWER key to
    blink is the fi rst number of the code. As you fi nd each
    number of the code, write it down for future reference.
    TIP: Each device key is associated with a type of device—the
    TV is preset to search for TVs, SAT•CBL•STREAM for
    satellite receivers, cable boxes, digital TV converters, or
    streaming media players, and DVD•VCR for VCRs or DVD
    players.
    The POWER key serves as an indicator light during
    programming, giving you feedback at each stage of the
    process.
    Auto Code Search
    The Auto Code Search goes automatically through all the
    codes for the device you’re trying to control. When you fi nd
    the one that operates your device, you can stop the search
    and store that code.
    TIPS: Each device key is associated with a type
    of device—the TV is preset to search for TVs,
    SAT•CBL•STREAM for satellite receivers, cable boxes,
    digital TV converters, or streaming media players, and
    DVD•VCR for VCRs or DVD players.
    To exit without saving a new code at any point in the
    Auto Code Search, press the
    GO BACK key.
    1. Manually turn on the device you
    want to control.
    3. Press and hold the device key you want to program.
    While you’re holding down the device key, use your
    other hand to press and hold the remote’s POWER
    key
    at the same time.
    2. If you’re programming the TV or
    SAT•CBL•STREAM key, go to step 3.
    If you’re programming the
    DVD•VCR key, you need
    to tell the remote which kind of device you want this
    key to control, VCR or DVD.
    Press and hold the
    DVD•VCR key. While you’re holding
    down the DVD•VCR key, use your other hand to press
    the number key for the type of device you want to
    control with this key: 2 for VCR, 3 for DVD.
    Testing the Code for Maximum Functionality
    1. Try a variety of the device’s functions with the remote.
    If some device features don’t work, go to next step to
    try a different code.
    2. Repeat the Auto Code Search Method from the
    beginning. When your device turns off, do not stop
    searching. Instead, with the unit now off, continue to
    press the PLAY key every 5 seconds until the unit turns
    back on.
    3. Once the unit turns back on, press the REVERSE key
    on the remote every 2 seconds until your device turns
    off again. When your device turns off again, press the
    STOP key.
    4. Test the key’s functionality again by attempting to
    control a variety of the device’s functions. If the code
    that has been stored controls the majority of the
    device’s functions, programming is complete. If the
    code stored does not give maximum functionality, try
    another code.
    4. Wait until the POWER key comes on and stays on.
    Then release both keys.
    5. Point the remote directly at the
    front panel of the device you
    want to control. Press PLAY on
    the remote and wait 5 seconds.
    The remote is testing a batch of
    10 codes on your device.
    Did your device turn off?
    YES: Go to step
    6.
    NO: Press PLAY again. The remote tests the next batch
    of 10 codes.
    Keep pressing PLAY every 5 seconds until your device
    turns off.
    6. When your device turns off, press
    the REVERSE key on the remote
    and wait at least 2 seconds.
    The remote tries the last of the
    previous ten codes.
    Did your device turn on?
    YES: Press the STOP key. You’re
    done! You’ve programmed this
    device key.
    NO: Press REVERSE again. The remote tests the next
    code in the batch.
    Keep pressing REVERSE every 2 seconds until your
    device turns back on. When it does, press STOP.
    Note: If you accidentally press the REVERSE key after
    your device turns on, press the FORWARD key. Then, wait
    two seconds to see if your device turns off again.
    NOTES
    Throughout the programming of each key, be sure to
    keep the remote pointed at the IR sensor of the device
    you are currently programming the remote to control.
    Test the remote with the device to make sure the
    device key is programmed with the correct code for
    maximum functionality. If some features don’t work, try
    a different code. See the “Testing the Code for Maximum
    Functionality” section below for more information.
    During the Auto Code Search, the remote ignores
    keypresses that aren’t part of the search.
    The search times out after two minutes (the
    POWER key
    blinks four times and turns off, and the last programmed
    code under that device key is retained).
    The
    POWER key blinks four times and turns off when the
    remote has gone through all the codes. The remote exits
    the Auto Code Search. If your device hasn’t turned off
    yet, try a different search method.
    Manual Code Search
    The Manual Code Search lets you go one-by-one through
    all the codes for the device you’re trying to control. When
    you fi nd the one that operates your device, you can stop the
    search and store that code.
    Actual model may vary from
    illustration
    TIPS: Each device key is associated with a type of device—
    the TV is preset to search for TVs, SAT•CBL•STREAM for
    satellite receivers, cable boxes, digital TV converters, or
    streaming media players, and DVD•VCR for VCRs or DVD
    players.
    The POWER key serves as an indicator light during
    programming, giving you feedback at each stage of the
    process.
    The Manual Code Search method may take a long time
    because the remote searches through all of the codes in
    its memory one-by-one. If your brand is listed in the Brand
    Codes or the Code Lists, fi rst try the Brand Code Search or
    the Direct Code Entry method.
    To exit without saving a new code at any point in the
    Manual Code Search, press the GO BACK key.
    DVD#VCR CODE
    DVD VCR
    1
    TV CODE
    5
    SAT#CBL#STREAM CODE
    SAT CABLE DTV CONVERTER
    STREAMING PLAYER
RCA RCR313BR

Brauchen Sie Hilfe?

Anzahl der Fragen: 0

Haben Sie eine Frage zum RCA RCR313BR oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere RCA RCR313BR-Eigentümer Ihre Frage richtig beantworten.

Sehen Sie sich hier kostenlos das Handbuch für RCA RCR313BR an. Dieses Handbuch fällt unter die Kategorie Fernbedienungen und wurde von 1 Personen mit einem Durchschnitt von 9 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum RCA RCR313BR oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

RCA RCR313BR-Spezifikationen

Allgemeines
Marke RCA
Model RCR313BR
Produkte Fernbedienung
EAN 863121542725
Sprache Englisch
Dateityp PDF
Leistungen
Anzahl der unterstützten Geräte 3
Maximale Reichweite -
Plug & Play
Design
Schnittstelle IR Wireless
Produktfarbe Schwarz
Fernbedienung Nutzung -
Eingangssignal Drucktasten
Bildschirm
Eingebaute Anzeige
Gewicht und Abmessungen
Gewicht -
Batterie
Eingebaute Batterie
Wiederaufladbar
Batterietechnologie -
Akku-/Batterietyp AAA

Häufig gestellte Fragen

Nachfolgend finden Sie die am häufigsten gestellten Fragen zu RCA RCR313BR .

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Bedienungsanleitu.ng

Auf der Suche nach einer Bedienungsanleitung? Bedienungsanleitu.ng sorgt dafür, dass Sie in Windeseile die Bedienungsanleitung finden, die Sie suchen. In unserer Datenbank befinden sich mehr als 1 Million PDF Bedienungsanleitungen von über 10.000 Marken. Jeden Tag fügen wir die neuesten Bedienungsanleitungen hinzu, damit Sie jederzeit das Produkt finden, das Sie suchen. Es ist ganz einfach: Tippen Sie in der Suchleiste Markenname und Produkttyp ein und Sie können direkt die Bedienungsanleitung Ihrer Wahl gratis online einsehen.

Bedienungsanleitu.ng

© Copyright 2020 Bedienungsanleitu.ng. Alle Rechte vorbehalten.

Diese Website benutzen Cookies. Wenn Sie die Website weiter nutzen, stimmen Sie der Verwendung von Cookies zu.

Erfahren Sie mehr