These instructions use the following symbols stated below:
SymbolKeywordExplanation
DANGER!Risk of severe personal injury
WARNUNG!Risk of minor personal injury
CAUTION!Risk of material damage
TIP:Useful notes
3. USE IN THE VEHICLE
Please observe the instructions for using children's restraining systems in the
operating instructions of your vehicle. During use, be sure to observe any restric-
tions relating to airbags.
Please refer to the operating instructions for your vehicle for information about
vehicle seats which are certified for the use of children's restraining systems according
to ECE R16.
TRIFIX i-SIZE usage options:
BRITAX RÖMER
child safety seat
Vehicle seat position with ISOFIX and
top tether
i-Size Not i-Size
TRIFIX i-SIZE
You can use your child safety seat as follows:
In the direction of travelYes
Against the direction of
travel
No
On seats featuring:
ISOFIX fastenings (be-
tween the seat surface
and backrest) and top
tether anchoring points
(e.g. on the loading area,
on the floor or behind the
backrest)
Yes
2)
(Please observe the applicable regulations in force in your country)
1) Using the seat in a backwards-facing car seat (e.g. in a van or minibus) is only permitted if
the car seat is also approved for transporting adults. The seat may not be in the area of eect
of an airbag.
2) If there is a passenger airbag: Slide the passenger seat well backwards and follow any
relevant directions in your vehicle's operating instructions.
76–105cm
≤ 22kg
Safety button
06
05
04
03
02
01
12
11
10
09
08
07
17
16
15
14
13
04
03
12
13
14
15
0102
07
08
09
10
11
17
16
We are pleased that you have chosen our
TRIFIX i-SIZE
to accompany your child safely through a new stage of his or her life.
In order to protect your child correctly, the
TRIFIX i-SIZE
must always be used and installed as described in these instructions.
The
TRIFIX i-SIZE
is exclusively intended to secure your baby
in your vehicle.
BRITAX RÖMER
child safety seat
Tested and approved according to
ECE* R 129/01
Body sizeBody weight
TRIFIX i-SIZE
76–105 cm≤ 22 kg
*ECE = European Standard for Child Safety Equipment
The child safety seat has been designed, tested and approved according to
the requirements of the European Standard for Child Safety Equipment (ECE
R 129/01). The seal of approval "E" (in a circle) and the approval number are
located on the orange approval label (sticker on the child safety seat).
DANGER! This certification will be invalidated if you make any modifica-
tions to the child safety seat. Only the manufacturer is permitted
to make modifications to the child safety seat. Unauthorised
technical changes can cause the protective function of the
seat to be reduced or completely eliminated. Do not make any
technical changes to the child safety seat.
DANGER! Use the
TRIFIX i-SIZE
exclusively for securing your child in your
vehicle. It is in no way suitable for use as a seat or toy in the
home.
PAGE I
4. CARE AND MAINTENANCE
Cleaning
Please only use authentic BRITAX RÖMER replacement seat covers. The
seat cover is an integral part of the child safety seat and is key to ensuring the
trouble-free functionality of the system. Replacement seat covers are available
from your dealer.
• The cover can be removed and washed with a mild detergent in the
delicates programme of the washing machine (30°C). Please observe the
instructions on the washing label of the cover.
• The shoulder pads can be removed and washed in luke-warm soapy
water.
• The plastic parts and the harness can be cleaned with soapy water. Do not
use any caustic cleaning agents (such as solvents).
Care for the harness buckle
To ensure the safety of your child, it is absolutely essential that the harness
buckle continues to function correctly. Harness buckle malfunctions are usu-
ally caused by a build-up of soiling or by external objects:
• When you press the red release button, it takes a long time for the buckle
tongues to be ejected.
• The buckle tongues no longer engage (i.e. when you try to push them in,
they pop out again).
• The buckle tongues engage without an audible "click".
• The buckle tongues are dicult to push in (you feel a certain amount of
resistance).
• The buckle can only be opened by applying extreme force.
Remedy: Clean the harness buckle so that it functions properly again with no
trouble:
Cleaning the harness buckle
1. Open the harness buckle
04
(press the red release button).
2. Unhook the elastic seam of the cover from the bottom edge of the seat
shell
17
.
3. Open the Velcro fastener on the crotch pad
18
and pull it over the harness
buckle
04
along with the cover.
4. Rotate the crotch harness with the metal plate
19
which holds the har-
ness buckle
04
in the seat shell
17
by 90° in the longitudinal slot.
5. Slide the metal plate
19
through the harness slot
20
with the narrow edge
facing forwards.
6. Soak the buckle
04
in warm water containing washing-up liquid for at least
an hour. Rinse the buckle thoroughly and dry it.
7. Slide the metal plate
19
fully into the longitudinal slot from the front.
8. Rotate the crotch harness with the metal plate
19
by 90° until it is hooked
into the harness slot
20
on the seat shell
17
perpendicular to the direction
of motion.
DANGER! Tug hard on the harness buckle
04
to make sure that it is
secure in the seat shell
17
.
9. Thread the harness buckle
04
through the crotch pad
18
on the cover
and then re-fasten the Velcro fastener and the cover.
Removing the cover
1. Push the tilt adjustment lever
11
upwards and slide back the seat shell
17
to upright position.
2. Loosen the shoulder straps
08
as far as possible.
3. Open the harness buckle
04
(press the red release button).
4. Open the Velcro fastener on the crotch pad
18
.
5. Slide the headrest
03
into the lowest position.
6. Pull o the cover of the headrest
03
.
7. Open the snap fasteners on the left and right of the rear part of the cover.
8. Turn over the rear part of the cover onto the seat surface.
9. Thread the shoulder straps
08
through the recesses in the cover. Unhook
the elastic seam of the cover from the bottom edge of the seat shell.
TIP: Start with the handles on the side and top of the seat shell.
10. Pull the cover up and over the border of the strap adjuster.
11. Unthread the harness buckle
04
and the strap end
09
from the cover.
12. Pull the cover upwards a little and then put it with the recess over the
headrest
03
.
DANGER! The child seat must not be used without the seat cover.
Reattaching the cover:
Proceed in reverse order to put on the cover.
Caution: The harnesses must not be twisted and must be correctly posi-
tioned in the harness slots.
Removing the shoulder pads
1. Loosen the shoulder straps
08
as far as possible.
2. Slide the headrest
03
into the second position from the top.
3. Fold up the bottom part of the headrest
03
upwards.
4. Open the shoulder pads
07
at the Velcro fasteners at the side.
Rear of the child safety seat
5. Open the operating instructions compartment
14
.
6. Pull out the shoulder straps
08
a little so that you can see the strap loops
of the shoulder pads
07
underneath.
7. Unhook the strap loops from the plastic fasteners
25
of the height ad-
juster.
8. Pull the shoulder pads
07
forwards out of the harness slots.
Re-attaching the shoulder pads:
Simply follow the steps above in reverse order.
Caution: The shoulder pads
07
or harnesses must not be twisted or
changed places. The shoulder straps
08
must be located under the black
cover band
21
in the shoulder pads
07
.
18
04
04
18
1920
08
11
03
08
03
07
07
25
08
76–105cm
≤ 22kg
TRIFIX i-SIZE
User instructions
www.britax.com
2000027224 17/06
GB
Sehen Sie sich hier kostenlos das Handbuch für Römer TRIFIX i-SIZE an. Dieses Handbuch fällt unter die Kategorie autositze und wurde von 1 Personen mit einem Durchschnitt von 6.2 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Römer TRIFIX i-SIZE oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage
Brauchen Sie Hilfe?
Haben Sie eine Frage zum Römer und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Römer -Besitzer, Ihnen eine gute Antwort zu geben.
Finden Sie die Antwort auf Ihre Frage nicht im Handbuch? Vielleicht finden Sie die Antwort auf Ihre Frage in den FAQs zu Römer TRIFIX i-SIZE unten.
Wie schwer ist das Römer TRIFIX i-SIZE?
Das Römer TRIFIX i-SIZE hat ein Gewicht von 10500 g.
Ist es für ein Baby sicher, in einem autositz zu schlafen?
Nein, das Baby könnte ersticken. Wenn ein Baby im autositz einschläft, sollte das Baby aus dem {Product} genommen und in eine Wiege gelegt werden. Nehmen Sie das Baby nach dem Einschlafen heraus und legen Sie es so schnell wie möglich in seine eigene Wiege.
Braucht mein zweijähriges Kind einen Autositz im Flugzeug?
Nein, Sie können ein Kind während des Fluges bis zu 24 Monate auf dem Schoß halten.
Was ist der sicherste Ort für einen Autositz?
Der sicherste Platz für einen Autositz befindet sich in der Mitte des Rücksitzes, so dass ein ausreichender Abstand zu den Airbags besteht.
Wie hoch ist das Römer TRIFIX i-SIZE?
Das Römer TRIFIX i-SIZE hat eine Höhe von 650 mm.
Wie breit ist das Römer TRIFIX i-SIZE?
Das Römer TRIFIX i-SIZE hat eine Breite von 450 mm.
Wie tief ist das Römer TRIFIX i-SIZE?
Das Römer TRIFIX i-SIZE hat eine Tiefe von 540 mm.
Ist das Handbuch der Römer TRIFIX i-SIZE unter Deutsch verfügbar?
Leider haben wir kein Handbuch für Römer TRIFIX i-SIZE in Deutsch verfügbar. Dieses Handbuch ist erhältlich in Englisch.
Brauchen Sie Hilfe?
Haben Sie eine Frage zum Römer und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Römer -Besitzer, Ihnen eine gute Antwort zu geben.
Anzahl der Fragen: 0