Sanyo FW32D06F Bedienungsanleitung

Troubleshooting Tips

If the Unit does not perform properly when operated as instructed in this Owner’s Manual,

Please check the following Troubleshooting Tips and All Connections Once before calling for Service.

Power

No Power

Make sure the AC Power Cord is plugged in.

Make sure that the AC outlet supplies the proper voltage, plug another

electrical appliance into the AC outlet to ensure that the AC outlet operates

normally.

If a Power Failure occurs, Unplug the AC Power Cord for 1 minute to allow the

Unit to Reset Itself.

Remote

Control keys do not work.

Do NOT press more than one key at the same time.

Ensure that no keys on the Remote Control are depressed and move freely.

Universal Remote Control does not work properly.

Refer to the User Manual of the Universal Remote Control for the SANYO

code.

Picture

Power is On but No Screen Image.

Check whether the Connection for the Antenna, Cable or Set-top Box is

Connected Correctly.

Check whether All the Cables to the Unit are connected to the correct Output

Jack on your separate Device like Blu-ray Disc / DVD Recorder.

Make sure that the selected Input mode is connected to the working Input

jack.

Check if your computer is NOT in Sleep Mode when the Input Mode on this

Unit is in PC mode. Tap any Key on the Computer Keyboard to Wake it up.

No Color

View other TV channels. The problem might be limited to the broadcasting

station.

Picture Poor

For the Best Picture Quality, watch “High Definition” wide screen Programs.

If the HD content is Not available, watch “Standard Definition” Programs

instead.

You see Pixelation on the Screen.

When the capabilities of the Unit exceed the capabilities of the Digital

Broadcasting, the signal will be increased to match the capabilities of the

Display on the Unit. This may cause Pixelation, Noise or Trash.

Unusual picture appears and the TV does Not Operate.

Press the Power key first. If it does not solve the problem, then press the keys

on the Remote Control in the order shown below to change the Unit to the

Live Mode.

Sound

No sound, distorted sound or incorrect Audio Sound is heard

when using the HDMI-DVI Connections.

Make sure that the Analog Audio signals from the HDMI-DVI Device are

connected to the Analog Audio (L/R) Input jacks.

Refer to For PC Input signal L p. 17

When using Component Analog Video, Composite Analog Video or HDMI-DVI

Video make sure that the Analog Audio (L/R) connectors are mounted into the

Audio (L/R) Input jacks.

Sound Intermittent or No Sound.

Check if the Audio Cable is connected into the Unit correctly.

You Switch to a Different Input and the Volume Changes.

This Unit will Memorize the Volume Level from the last time you adjusted it.

If the Volume of the Sound from another Device is Higher or Lower, then the

Loudness will Change.

Picture & Sound

No Picture or Sound

Check if the Power is On.

Check whether All the cables to the Unit are connected to the correct Output

jack of your device like Blu-ray / DVD Recorder.

View other TV channels. The problem might be limited to the Broadcasting

Station or Weak Signal Strength, if DTV channel check signal strength. Refer

Unplug the AC Power Cord and wait for about 1 minute, then Plug the AC

Power Cord and turn On the Unit again.

Check whether the Connection of the Antenna or Cable or Set-top Box is

connected correctly.

Make sure that the selected Input mode is connected to the working Input

jack.

Check if your computer is NOT in sleep mode when the Input mode of this

Unit is in PC mode. Tap any key on the keyboard to wake up your computer.

current volume level will appear on the TV screen.

to the desired volume.

Adjusted Picture or Sound settings are not the same (memorized)

every time the Unit is turned On.

adjusted will not be memorized after the Unit goes into Standby Mode.)

- NTSC signal)

You may be getting interference from electrical appliances, automobiles,

motorcycles or fluorescent lights.

Try moving the Unit to another Location to see if this is the Cause of the

Problem.

Ghosts, lines or streaks in picture. (Analog TV- NTSC signal)

Electrical interference from nearby appliances may affect picture quality.

View other TV channels. The problem might be limited to the Broadcasting

Station or Weak Signal Strength, if DTV channel check signal strength. Refer

Picture Poor, Sound Intermittent or No Sound

View other TV channels. The problem might be limited to the Broadcasting

Station or Weak Signal Strength, if DTV channel check signal strength. Refer

Screen

You Switch to a different Input and the Screen Size changes.

This Unit will Memorize the Viewing Mode from the last time you used those

Particular Input Modes.

The Display image does not cover the Entire Screen.

If you are watching TV or using the Composite Video, Component Video or

Screen Modes.

Different color marks on the TV screen

View other TV channels. The problem might be limited to the broadcasting

station, missing data or pixelation due to weak signal strength.

Closed Captions

are displayed in the Closed Captions-Supported Program.

Interference from buildings or weather conditions may cause captioning to be

incomplete if watching Analog TV signals.

Broadcasting Station may shorten the program to insert advertisements.

The Closed Captions Decoder cannot read the information of a shortened

program.

Black Box is displayed on the TV Screen.

CC-4. L p. 23

If connected to a Blu-ray / DVD device then Closed Captions are part of its Video

signal and is only controlled through this Device's Menu or Remote Control.

Remove the TV Closed Captions mode.

Note(s)

The LCD screen is manufactured to provide many years of useful life.

Occasionally a few non active pixels may appear as a fixed point of blue, green

or red.

This is Not to be considered a Defect in the LCD screen.

Some Functions are Not available in Specific Modes, but this is Not a

Malfunction. Read the Description in this Owner’s Manual for more Details

on Correct Operations of this Unit.

33 .English