Siemens WT46W592 Bedienungsanleitung

Siemens WT46W592
8 · 5
PDF Bedienungsanleitung
 · 10 Seiten
Englisch
BedienungsanleitungSiemens WT46W592
8

Installation

 Scope of delivery: dryer, installation and instruction manual, basket for woollens (depending on the model). Check dryer for transport damage. The dryer is very heavy. Do not lift without assistance. Be careful to avoid sharp edges. Do not install in a room which is susceptible to frost. Water may cause damage once it starts to freeze. If in doubt, have the appliance connected by a specialist. Do not lift the dryer by any of the protruding parts (e.g. the door) as they may break off.Setting up the dryer The appliance plug must always be accessible. Ensure that the appliance is installed on a clean, level and firm surface. Do not obstruct the air inlet on the front of the dryer. Keep the area around the dryer clean. Level the dryer using the threaded feet.Use a spirit level. Do not remove the threaded feet under any circumstances.Mains connection see safety information
a
Page 13. Connect to an AC earthed socket. If in doubt, have the socket checked by a specialist. The mains voltage and the voltage shown on the rating plate (
a
Page 10) must be the same. The connected load and necessary fuse protection are specified on the rating plate.

Frost protection

Preparation1. Empty the condensation container
a
page 4.2. Select any programme using the programme selector.3. Press the Start/Stop button
a
condensation is pumped into the container.4. Wait 5 minutes and then empty the condensation container again.5. Turn the programme selector to Aus (Off).

Transport

 Preparation of dryer
a
see Frost protection. Transport the dryer in a vertical upright position. Following transportation, leave the dryer to stand for two hours.There may be residual water in the dryer.This can leak out if the dryer is at an angle.
1.
Remove all accessories from the drum.The drum must be empty.
Make sure that the air inlet remains unobstructedClean and level
Do not install the dryer behind a door or sliding door, which could prevent or restrict opening of the dryer door. This will prevent children from locking themselves in and putting their lives in danger.
2.
Do not operate the dryer if there is a danger of frost.
9
Only when the appliance is switched off.

Care and cleaning

Heat exchangerThe heat exchanger of the dryer is cleaned automatically when drying is in progress, Clnappears in the display panel. Do not pull the condensation container out during the cleaning process.Dryer housing, control panel, air intakeWipe with a soft, damp cloth.Do not use harsh cleaning agents or solvents.Remove detergent and cleaning agent residue immediately.Some water may collect between the window and the seal during drying. This does not affect the proper operation of your dryer in any way.Filter in the condensation tankThe filter is cleaned automatically when the condensation container is emptied. However, the filter should still be cleaned regularly under running water. This prevents stubborn deposits/dirt from building up.Cleaning is only required if the symbol ā flashes again in the display panel after the condensation container has been emptied.1. Pull out the condensation container.2. Pull the filter out of its snap-in lock.3. Clean the filter under running water or in the dishwasher.4. Refit the filter.5. Insert the condensation tank so that it locks into place.Only operate the dryer with the filter inserted.Moisture sensorThe dryer is equipped with stainless-steel moisture sensors. These measure how damp the laundry is. After long periods of use, a fine layer of limescale can form on the moisture sensors.1. Open the door.2. Clean the moisture sensors using a damp sponge with a rough surface.Do not use steel wool or other abrasive materials.
10

Technical data

ʠ
Dimensions (DxWxH) 60 x 60 x 85 cm (adjustable height)Weight approximately 53 kgMax. capacity 7 kgCondensation container 4.0 lConnection voltage 220-240 VConnected load max. 1000 WFuse protection 10 AAmbient temperature 5 - 35 °CProduct numberProduction numberInside of doorThe rating plate can be found on the back of the dryer.
ʠ
Consumption ratesThese are guide values determined under standard conditions.Spin speed in rpm (residual moisture)Drying timein min.**Energy consumptionin kWh**Cottons/Coloureds 7 kgCupboard Dry* 1400 (approx. 50 %) 112 1.351000 (approx. 60 %) 131 1.60800 (approx. 70 %) 150 1.86Iron Dry* 1400 (approx. 50 %) 80 0.961000 (approx. 60 %) 99 1.22800 (approx. 70 %) 118 1.47Easy-Care 3.5 kg
Cupboard Dry* 800 (approx. 40 %) 51 0.56
600 (approx. 50 %) 63 0.70*Test programme to DIN EN 61121**The values may differ from those given, depending on overvoltage and undervoltage, the type of fabric, composition of the laundry to be dried, the residual moisture in the fabric and the size of the load.
ʠ
Drum interior light (bulb E14, 25 W)The drum is illuminated after the door is opened or closed, and after the programme has started. The light goes out automatically. To change the bulb
a
page 12.

Optional accessories (order from the after-sales service using the order number)

PlatformFor better loading and unloading. The basket contained in the drawer can be used to carry the laundry.Washer-dryer stack connection setThe dryer can be stacked on top of a suitable washing machine of the same depth and width, to save space. The dryer must be secured to the washing machine with this connection set.Same as WZ 20310, but with pull-out worktop.Installation underneath the worktopInstead of the appliance covering plate, you must have a metal cover fitted by a specialist.
WZ
20460
WZ
20310
WZ
20300
WZ
20290
11

Normal noises

During drying, the compressor and the pump generate some noise which is entirely normal.The compressor in the dryer may occasionally generate a droning noise.The compressor in the dryer is ventilated from time to time, which creates a whirring sound.The automatic cleaning process causes a clicking noise.The process of pumping the condensation into the condensation container generates pumping noises.
12

What to do if ...

If you cannot rectify a fault yourself, please contact our after-sales service. We will always find an appropriate solution and will avoid unnecessary visits by engineers. Trust the expertise of the manufacturer and rest assured that the repair will be carried out by trained service technicians using original spare parts. The contact details of your local after-sales service can be found in the enclosed after-sales service directory, or by calling one of these numbers:GB 0844 8928999 (Calls from a BT landline will be charged at up to 3 pence per minute. A call set-up fee of up to 6 pence may apply.)IE 01450 2655 When contacting the after-sales service, please quote the appliance's product number (E no.) and production number (FD) (see the inside of the door).Set the programme selector to Aus (Off) and remove the appliance plug from the socket.
ʠ
The Start/Stop indicator lamp does not light up.Mains plug plugged in?Programme selected?
ʠ
The ā symbol and Start/Stop indicator lamp flash.Empty container for condensation
a
see page 4.Clean the condensation container filter if necessary
a
page 6.Each time the dryer is transported, you must wait two hours before operating it.
ʠ
The 4 symbol and Start/Stop indicator lamp flash.Rinse the fluff filter under running water
a
page 4.
ʠ
Dryer does not start. Start/Stop button selected?Door closed?Programme set?Ambient temperature greater than 5 °C?
ʠ
Water is leaking out. Make sure the dryer is level.
ʠ
The door opens by itself. Push the door closed until you hear it click into place.
ʠ
Drying result was not achieved (laundry too damp).Hot laundry feels damper than it actually is.The selected programme does not suit the load. Use another drying programme or, in addition, select the time programme a page7.Use fine adjustment for the drying result a page1/2.Fine layer of limescale on the humidity sensors a Clean the humidity sensors apage 9.Programme cancellation, e.g. tank full, mains power supply failure, door open or maximum drying time reached.
ʠ
Drying time too long. Clean the fluff filter under running water a page 4.
Insufficient supply of air a ensure that air can circulate.
Air inlet possibly blocked a Clear inlet a page 8.
Ambient temperature higher than 35 °C a Ventilate the room.
ʠ
The humidity in the room increases significantly.Make sure the room is sufficiently ventilated.
ʠ
Cln appears in the display panel. Not an error! Automatic cleaning of the heat exchanger.
Do not empty the condensation container.
ʠ
Power cut. Remove the laundry from the dryer immediately and spread it out. Heat may escape.
ʠ
The interior light is not working. Unplug the appliance plug, fold back the cover cap on the inside above the door (using a Torx 20 screwdriver) and replace the bulb. Close the cover cap.Never operate the dryer without a cover cap.
ʠ
Other intermittent noises and vibrations.Not an error!Normal noises
a
page 11.
ʠ
Loud humming noise for several seconds.Has the condensation container been properly reinserted?
a
Push the condensation tank all the way in.Not an error! Normal noises
a
page 11.
13

Safety instructions

Emergency Pull the appliance plug out of the socket immediately or disconnect the fuse.ONLY use the dryer... In rooms inside the house. To dry fabrics. The dryer must NEVER... Be used for purposes other than those described above. Be modified in terms of its technology or properties.Hazards The dryer must not be used by children or persons who have not been instructed in its use. Do not leave children unsupervised near the dryer. Keep pets away from the dryer. Remove all objects from the pockets of garments.Pay particular attention to cigarette lighters
a
Risk of explosion Do not lean or sit on the door
a
Risk of tipping.Installation Secure loose cables
a
Tripping hazard. Do not operate the dryer where there is a risk of frost.Mains connection Connect the dryer according to specifications to an AC earthed socket, otherwise it cannot be guaranteed that the appliance is completely safe. The cable cross-section must be sufficient. Only use earth-leakage circuit breakers with the following symbol:  The appliance plug and socket must be compatible. Do not use multiple plugs/connectors and/or extension cables.  Do not touch or hold the appliance plug with wet hands
a
Risk of electric shock. Never pull the appliance plug out of the socket by its cable. Do not damage the mains lead
a
Risk of electric shock.Operation Only laundry must be loaded into the drum.Before switching on the dryer - check the contents. Do not use the dryer if the laundry has been in contact with solvents, oil, wax, grease or paint (e.g. hair setting spray, nail polish remover, stain remover, cleaning solvent, etc.)
a
Fire/explosion hazard. Hazard caused by dust (e.g. coal dust, flour): do not use the dryer
a
Risk of explosion! Do not put laundry containing foamed material/rubber in the dryer
a
elastic material may be destroyed and the dryer may be damaged due to possible deformation of the foamed material. Switch off the dryer once the programme has ended. The water from condensation is not drinking water and may be contaminated with fluff.Defect Do not use the dryer if it is defective or if you suspect that it is.Repairs must only be carried out by the after-sales service. Do not use a dryer with a faulty mains lead. To prevent risks, a faulty mains lead must only be replaced by the after-sales service. Before changing the bulb of the interior light make absolutely sure you have pulled the appliance plug from the socket
a
Risk of electric shock!Spare parts Only use genuine spare parts and accessories for safety reasons.Disposal
Dryer: unplug the appliance plug, then cut the mains lead from the appliance.
Dispose of the dryer at an approved public disposal facility. The heat exchanger contains fluorinated greenhouse gas R-407C covered by the Kyoto Protocol a dispose of in a proper manner. Capacity: 0.43 kg. Packaging: keep all packaging out of reach of babies and children.
a
Danger of suffocation! All materials are environmentally safe and recyclable. Dispose of in an environmentally-responsible manner.
Operating
and installation instructions
en

Bedienungsanleitung

Sehen Sie sich hier kostenlos das Handbuch für Siemens WT46W592 an. Dieses Handbuch fällt unter die Kategorie Trockner und wurde von 5 Personen mit einem Durchschnitt von 8 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Siemens WT46W592 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Brauchen Sie Hilfe?

Haben Sie eine Frage zum Siemens WT46W592 und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Siemens WT46W592-Besitzer, Ihnen eine gute Antwort zu geben.

Dieter • 7-2-2015 Keine Kommentare

wer kann mir sagen, warum meine Maschine das Kondenswasser nicht mehr in den Behälter pumpt, obwohl der Behälter leer ist. Maschine ( Display) BITTE Wasser leeren. Nach mehreren Monaten ist wahrscheinlich das Wasser verdunstet, somit geht die Maschine einmal, dann wieder die gleiche Fehlermeldung. Wer hat eine Idee. Danke im Voraus Dieter

Diese Frage beantworten

Anzahl der Fragen: 1

Siemens WT46W592-Spezifikationen

Nachfolgend finden Sie die Produktspezifikationen und die manuellen Spezifikationen zu Siemens WT46W592.

A bedeutet, dass das Produkt in Bezug auf Energieeffizienz in seiner Kategorie am besten bewertet wird. Das Energiekennz...
Allgemeines
Marke Siemens
Model WT46W592
Produkte Trockner
EAN 4242003534472
Sprache Englisch
Dateityp Benutzerhandbuch (PDF)
Leistung
Energieeffizienzklasse A
AC Eingangsspannung 220 - 240 V
AC Eingangsfrequenz 50 Hz
Anschlusswert 1000 W
Nennstrom 10 A
Design
Geräteplatzierung Freistehend
Ladetyp Frontlader
Trocknungssystem Kondensation
Kabellänge 1.45 m
Türanschlag Rechts
Trommelvolumen 112 l
Trommelmaterial Edelstahl
Produktfarbe Weiß
Eingebautes Display Ja
Display-Typ LCD
Leistungen
Anpassbare Rotationsgeschwindigkeit Ja
Anti-Falten Programm 120 min
Zykluszeit 112 min
Geräuschpegel 65 dB
Anti-Faltenfunktion Ja
Minimale Schleuderdrehzahl 800 RPM
Maximale Schleuderdrehzahl 1400 RPM
Nennkapazität 7 kg
Trockenprogramme Wool,Mix,Timed
Ergonomie
Einschalteverzögerung (max.) 24 h
Startzeitvorwahl Ja
Trommelinnenbeleuchtung Ja
Restzeitanzeige Ja
Technische Details
Energieverbrauch (Schranktrocken) 1.4 kWh
Gewicht und Abmessungen
Breite 598 mm
Tiefe 625 mm
Höhe 842 mm
Gewicht 54000 g
Mehr anzeigen

Häufig gestellte Fragen

Finden Sie die Antwort auf Ihre Frage nicht im Handbuch? Vielleicht finden Sie die Antwort auf Ihre Frage in den FAQs zu Siemens WT46W592 unten.

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Keine Ergebnisse