Sony DPT-CP1

Sony DPT-CP1 Bedienungsanleitung

  • 4-733-170-11(2)
    © 2017 Sony Corporation / Printed in China
    Digital Paper System
    Quick Start Guide
    Help Guide (online manual)
    This Quick Start Guide explains how to use the device
    for the first time and gives safety precautions. For
    further details, refer to the online Help Guide:
    Owner’s Record
    The model and serial number are located at the rear of the
    device. Record the serial number in the space provided below.
    Refer to these numbers whenever you contact your Sony dealer
    regarding this product.
    Model No. DPT-CP1
    Serial No.
    Getting Started
    Checking the supplied items
    Check the following items are present.
    •Digital Paper device (1)
    •Stylus (1)
    •Replacement tips
    Felt (gray) (1)
    POM (black) (2)
    •Tip puller (1)
    •USB cable (1)
    •Quick Start Guide (this document) (1)
    •Warranty (1)
    For approved accessories, refer to the following Digital Paper product page:
    Initial setup
    Set up the Digital Paper device (hereafter referred to as “the
    device”) and your computer according to the instructions
    1 Turn on the device.
    2 Set a stylus according to the instructions on the screen.
    3 Turn on the computer and connect to the Internet.
    4 Download Digital Paper App from the following site and
    install on the computer.
    Digital Paper App is required to transfer documents (PDF
    5 Start Digital Paper App and connect the supplied USB cable
    to the micro USB connector of the device and the USB
    connector of the computer.
    6 Set the computer according to the instructions displayed
    by Digital Paper App.
    Documents can be transferred only between the device and
    the computer.
    7 Update the app software if a software update is advised.
    Wi-Fi is used only for transferring documents between the device and the
    computer. The device cannot display Internet content.
    Charging the device and stylus
    1 Turn on the computer.
    2 Connect the supplied USB cable to the micro USB connector
    of the device or stylus and the USB connector of the
    Charge indicator
    Charge indicator
    •Charge the device and stylus within the recommended temperature range of
    5 °C to 35 °C (41 °F to 95 °F). If the room is too hot or cold, disconnect the USB
    cable, adjust the room temperature accordingly, then reconnect the USB cable
    to charge.
    •The device and stylus will not charge if your computer is turned off, enters sleep
    mode, standby mode or hibernation mode.
    The Charge indicator lights up in red while charging.
    Parts and controls
    Digital Paper device
    RESET button
    Micro USB connector
    (power) button
    Charge indicator
    Magnet (for holding the
    (home) button
    Strap hole
    Micro USB connector
    Strap hole
    Charge indicator
    Part for holding to the
    Highlight button
    Eraser button
    The following information will help you remedy problems if you
    cannot operate the device.
    1 Charge the device and the stylus.
    2 Reset the device.
    Press the RESET button with a plastic toothpick, clip, etc.
    Press the (power) button to restart the device.
    •Content handwritten within documents, created notes, and settings may be
    deleted when the device is reset.
    •Do not press the RESET button with a fragile object (pencil lead, etc.).
    How to use the system and the
    support site
    For more detailed information on using the Digital Paper
    System, see
    If you cannot recover the device
    Consult the Sony Support Center and provide the following
    •Model name (specified on the back panel)
    •Serial number (specified on the back panel)
    •Purchase date
    Replacing the stylus tip
    The stylus tip may wear out through use. It is recommended to
    replace the tip when it becomes shorter than 1.5 mm (1/16 in).
    Replacement tips and a tip puller are supplied with the device.
    Replace the tip when it becomes
    shorter than 1.5 mm (1/16 in)
    1 Pinch the tip with the supplied tip puller, then pull it out
    Pinch the base of the tip firmly
    2 Check the orientation of the replacement tip, pinch it with
    the tip puller, then push it straight into the stylus.
    3 Push the tip firmly with your finger.
    •Keep out of reach of children, as the tip may be swallowed. In case the tip is
    swallowed, please consult your doctor.
    •Pressing on the tip with excessive pressure will wear it out more quickly.
    •Replace the stylus tip periodically to prevent damage to the device and
    maintain consistent operation.
    •If the stylus tip is lost, contact the Sony Support Center.
    Important Information
    Do not expose the battery to fire or heat.
    Do not disassemble the battery.
    It may cause electric shock. Do not remove the battery yourself.
    For battery replacement, internal checking or repair, consult the
    Sony Support Center.
    Do not charge the device near fire, heat, or leave it in hot
    Do not leave coins, keys, jewelry, etc., near the USB
    connector or USB cable.
    Do not use the device while moving.
    Do not operate the device or watch the display while driving a
    vehicle, riding a motor cycle, walking, etc.
    Do not use the device where it may distract you from
    danger; for example at a railroad crossing, road,
    construction site, etc.
    Be careful not to allow liquid or a foreign object to get into
    the device, as doing so may cause electric shock or fire.
    If liquid or a foreign object gets into the device, consult the
    Sony Support Center.
    Keep out of reach of children.
    The stylus or replacement tip may be accidentally swallowed. If
    the battery is swallowed, consult a doctor immediately. It may
    cause choking or damage the stomach.
    Never subject the device to high temperature.
    Never subject the device to extremes of light, high temperature
    (more than 60 °C (140°F)), moisture or vibration.
    For example, if the device is left in a car parked in the sun,
    excessive heat buildup may result in deformation of the device
    casing, or other malfunction.
    Do not cover the device with a blanket when turned on.
    The device may overheat and deform or catch fire.
    If you feel discomfort while using the device, stop using it.
    Do not leave the device on an unstable surface.
    Do not leave the device on an unstable or sloping surface. Do
    not stand the device upright, or turn it upside down. The device
    may drop or be damaged.
    The device screen is delicate.
    If heavy weight or force is applied, the screen may be
    Handling the device
    •If the device causes interference to radio or television
    reception, turn the device off and move it away from the radio
    or television.
    •Refrain from using the device in an aircraft according to the
    inflight announcements during taking off or landing.
    •When you put the device into a bag, make sure no objects
    with sharp or hard edges come into direct contact with the
    •Do not drop, or put any heavy object on top of the device or
    apply a strong shock to the device. It may cause a
    malfunction or damage.
    •Never subject the device to extremes of light, temperature,
    moisture or vibration.
    •If part of the device that generates heat contacts your skin for
    a prolonged period, you may suffer burn symptoms, such as
    redness, swelling, even if the temperature is moderate. Avoid
    prolonged contact, especially if you have sensitive skin.
    •Do not leave the device on an unstable surface.
    •Do not poke people with the supplied stylus.
    •Do not treat or use the supplied stylus roughly, such as
    bending it, or scratching the touchscreen with it.
    •Use the supplied stylus only for touchscreen operations.
    •Do not use the stylus if it is damaged or deformed.
    •Do not subject the stylus to shock or vibration.
    •Do not apply any excessive pressure to the stylus tip and
    stylus button during operation.
    •Do not keep the stylus tip pressed while the stylus is not in
    •Do not leave the stylus on the touchscreen. It wastes battery
    charge of the device and stylus.
    •If an object is placed on the touchscreen, it may cause a
    malfunction. When not in use, leave the device in sleep mode,
    or turn it off.
    •When using the device another country/region, it is your
    responsibility to ensure that it is used in compliance with the
    following specifications:
    AC voltage
    Wireless products regulations
    Other safety regulations or requirements
    •Be sure not to short-circuit the terminals of the device with
    metallic objects.
    •Never leave the device exposed to high temperature, such as
    in a car parked in the sun or under direct sunlight.
    •As the device uses magnets, it may affect medical equipment
    such as a cardiac pacemaker, defibrillator, or programmable
    shunt valve. Do not put the device close to medical
    equipment or people using medical equipment. If you use
    medical equipment and feel anxious, consult your doctor
    before you use the device.
    Avoiding water and moisture
    •If the unit is suddenly taken from a cold to a warm location, or
    if ambient temperature suddenly rises, moisture may form on
    the outer surface of the unit and/or inside of the unit. This is
    known as condensation. If condensation occurs, turn off the
    unit and wait until the condensation clears before operating
    the unit. Operating the unit while condensation is present
    may damage the unit.
    •The device is not waterproof. Remember to follow the
    precautions below.
    Be careful not to drop the device into a sink or other
    container filled with water.
    Do not use the device in humid locations or bad weather,
    such as in the rain or snow.
    Do not get the device wet.
    If you touch the device with wet hands, or put it in a damp
    article of clothing, the device may get wet and this may cause a
    Charging the device
    •Heat may build up in the device while charging, or if it is used
    for an extended period of time.
    •Use the supplied USB cable only. Do not use any other USB
    •Never wrap the device in anything when it is being charged.
    Heat build-up in the device may cause malfunction or
    •If the battery lasts only half the normal time even after being
    fully charged, it may be reaching the end of its life.
    Cleaning the device
    •Clean the device with a soft cloth, such as a cleaning cloth for
    eyeglasses. Make sure that there is no dust or dirt on the soft
    cloth, as the device may be damaged.
    •Do not use any type of abrasive pad, scouring powder or
    solvent, such as alcohol or benzene, as it may mar the finish
    of the case.
    •Wipe the stylus with a dry cloth when it gets dirty. Tapping or
    dragging on the touchscreen using a dirty stylus may damage
    the surface.
    •Be sure to keep the device away from water or spills.
    Regulatory information
    This device displays the information below.
    The Declaration of Conformity (DoC) logo and the FCC Identifier (FCC
    ID) based on the FCC Rules
    The marks and registration numbers of the radio wave and radio
    communication acts
    You can display these marks or registration numbers.
    Press the
    (home) button, then tap [Settings] - [Regulatory
    If you cannot display the marks or registration numbers due to a
    malfunction, contact the Sony Support Center.
    For the customers in the U.S.A.
    This equipment has been tested and found to comply with the limits
    for a Class B digital device, pursuant to part 15 of the FCC Rules. These
    limits are designed to provide reasonable protection against harmful
    interference in a residential installation. This equipment generates, uses
    and can radiate radio frequency energy and, if not installed and used
    in accordance with the instructions, may cause harmful interference to
    radio communications. However, there is no guarantee that interference
    will not occur in a particular installation. If this equipment does cause
    harmful interference to radio or television reception, which can be
    determined by turning the equipment off and on, the user is encouraged
    to try to correct the interference by one or more of the following
    Reorient or relocate the receiving antenna.
    Increase the separation between the equipment and receiver.
    Connect the equipment into an outlet on a circuit different from that
    to which the receiver is connected.
    Consult the dealer or an experienced radio/TV technician for help.
    This DPT-CP1 has been tested and meets the FCC RF exposure guidelines
    when used with the Sony Corporation accessories supplied or designated
    for this product. Use of other accessories may not ensure compliance
    with FCC RF exposure guidelines.
    Changes or modifications not expressly approved by the party
    responsible for compliance could void the user’s authority to operate the
    If you have any questions about this product, you may call:
    Sony Customer Information Service Center 1-800-222-7669 or http://
    Declaration of Conformity
    Trade Name : SONY
    Model : DPT-CP1
    Responsible party : Sony Electronics Inc.
    Address : 16535 Via Esprillo, San Diego, CA
    92127 U.S.A.
    Telephone Number : 858-942-2230
    This device complies with part 15 of the FCC Rules. Operation is subject
    to the following two conditions: (1) This device may not cause harmful
    interference, and (2) this device must accept any interference received,
    including interference that may cause undesired operation.
    FCC Radiation Exposure Statement
    The available scientific evidence does not show that any health problems
    are associated with using low power wireless devices. There is no proof,
    however, that these low power wireless devices are absolutely safe. Low
    power Wireless devices emit low levels of radio frequency energy (RF)
    in the microwave range while being used. Whereas high levels of RF
    can produce health effects (by heating tissue), exposure of low-level RF
    that does not produce heating effects causes no known adverse health
    effects. Many studies of low-level RF exposures have not found any
    biological effects. Some studies have suggested that some biological
    effects might occur, but such findings have not been confirmed by
    additional research. DPT-CP1 has been tested and found to comply with
    FCC radiation exposure limits set forth for an uncontrolled environment
    and meets the FCC radio frequency (RF) Exposure Guidelines.
    In order to comply with FCC radio-frequency radiation exposure
    guidelines for an uncontrolled exposure, this device and its antenna
    must not be co-located or operating in conjunction with any other
    antenna or transmitter.
    For the customers in the U.S.A.
    warranty for important information and complete terms and conditions
    of Sony’s limited warranty applicable to this product.
    For the customers in Canada
    SONY LIMITED WARRANTY - Please visit
    lang/en/ca/article/resources-warranty for important information and
    complete terms and conditions of Sony’s limited warranty applicable to
    this product.
    For the customers in Europe
    Sony Professional Solutions Europe - Standard Warranty and Exceptions
    on Standard Warranty. Please visit
    for important information and complete terms and conditions.
    For the customers in Korea
    SONY LIMITED WARRANTY - Please visit
    handler/BPAS-Start for important information and complete terms and
    conditions of Sony’s limited warranty applicable to this product.
    End User License Agreement
    •You can display the End User License Agreement from the
    Press the
    (home) button, then tap [Settings] [System
    Information] [End User License Agreement].
    •The display is made of plastic film to be thin and lightweight.
    When the device is illuminated, distortion of the plastic film
    may occur. This is not a malfunction.
    •Do not apply excessive pressure to the touchscreen. The color
    or brightness may become uneven and may cause the device
    to malfunction.
    •When using the device in a cold environment, the screen may
    change at a slower speed. This is not a malfunction.
Sony DPT-CP1

Brauchen Sie Hilfe?

Anzahl der Fragen: 0

Haben Sie eine Frage zum Sony DPT-CP1 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere Sony DPT-CP1-Eigentümer Ihre Frage richtig beantworten.

Sehen Sie sich hier kostenlos das Handbuch für Sony DPT-CP1 an. Dieses Handbuch fällt unter die Kategorie E-Reader und wurde von 1 Personen mit einem Durchschnitt von 7.5 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Sony DPT-CP1 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Sony DPT-CP1-Spezifikationen

Marke Sony
Model DPT-CP1
Produkte E-Reader
Sprache Englisch
Dateityp PDF