Sony SAL-70200G

Sony SAL-70200G Bedienungsanleitung

(1)
  • (1) (2)
    (1) (2)
    (3) (4)
    21 3
    4
    5
    6
    7
    8
    910
    16
    15
    14
    13
    12
    11
    1···Focusing ring 2···Zooming ring 3···Focal-length scale
    4···Focal-length index 5···Collar mounting index (red)
    6···Lens index (gray) 7···Collar index (gray) 8···Lens
    contacts 9···Distance index 10···Distance scale
    11···Focus-mode switch 12···Lens mounting index
    13···DMF-mode switch 14···Focus-range limiter
    15···Collar-locking knob 16···Focus-hold button
    This lens is designed for Sony cameras.
    WARNING
    To reduce fire or shock hazard, do not expose the unit to rain or moisture.
    Do not directly look at the sun through this lens.
    Doing so might harm your eyes or cause loss of eyesight.
    Keep the lens out of reach of small children.
    There is danger of accident or injury.
    Disposal of Old Electrical & Electronic Equipment
    (Applicable in the European Union and other
    European countries with separate collection
    systems)
    This symbol on the product or on its packaging indicates that
    this product shall not be treated as household waste. Instead it
    shall be handed over to the applicable collection point for the
    recycling of electrical and electronic equipment. By ensuring this product is
    disposed of correctly, you will help prevent potential negative consequences
    for the environment and human health, which could otherwise be caused
    by inappropriate waste handling of this product. The recycling of materials
    will help to conserve natural resources. For more detailed information
    about recycling of this product, please contact your local Civic Office, your
    household waste disposal service or the shop where you purchased the
    product.
    For the customers in the U.S.A.
    THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
    OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
    (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE,
    AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
    RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
    UNDESIRED OPERATION.
    CAUTION
    You are cautioned that any changes or modifications not expressly approved
    in this manual could void your authority to operate this equipment.
    NOTE:
    This equipment has been tested and found to comply with the limits for a
    Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
    are designed to provide reasonable protection against harmful interference
    in a residential installation. This equipment generates, uses, and can radiate
    radio frequency energy and, if not installed and used in accordance with the
    instructions, may cause harmful interference to radio communications.
    However, there is no guarantee that interference will not occur in a particular
    installation. If this equipment does cause harmful interference to radio or
    television reception, which can be determined by turning the equipment off
    and on, the user is encouraged to try to correct the interference by one or
    more of the following measures:
    Reorient or relocate the receiving antenna.
    Increase the separation between the equipment and receiver.
    Connect the equipment into an outlet on a circuit different from that to which the
    receiver is connected.
    Consult the dealer or an experienced radio/TV technician for help.
    For the customers in Canada
    This Class B digital apparatus complies with Canadian ICES-003.
    Notes on use
    Do not leave the lens in direct sunlight. If sunlight is focused onto a nearby
    object, it may cause a fire. If circumstances necessitate leaving the lens in direct
    sunlight, be sure to attach the lens cap.
    Be careful not to subject the lens to mechanical shock while attaching it.
    Always place the lens caps on the lens when storing.
    Do not keep the lens in a very humid place for a long period of time to prevent
    mold.
    Hold both the camera and lens, when you carry the camera with the lens
    attached.
    Do not touch the lens contacts. If dirt, etc., gets on the lens contacts, it may
    interfere or prevent the sending and receiving of signals between the lens and the
    camera, resulting in operational malfunction.
    Vignetting
    When you use lens, the corners of the screen become darker than the center.
    To reduce this phenomena (called vignetting), close the aperture by 1 to 2
    stops.
    Names of parts
    ©2006 Sony Corporation Printed in Japan
    SAL70200G
    Lens for Digital Single Lens
    Reflex Camera
    Operating Instructions
    70-200mm F2.8 G
    2-696-862-11(1)
    Attaching/detaching the lens
    To attach the lens
    1 Remove the rear and front lens caps and the camera body cap.
    You can attach/detach the front lens cap in two ways, (1) and (2). When you attach/detach the
    lens cap with the lens hood attached, use method (2).
    2 Align the orange index on the lens barrel with the orange index on the
    camera (mounting index), then insert the lens into the camera mount and
    rotate it clockwise until it locks.
    Do not press the lens release button on the camera when mounting the lens.
    Do not mount the lens at an angle.
    To remove the lens
    While pressing and holding the lens release button on the camera, rotate the
    lens counterclockwise until it stops, then detach the lens.
    Attaching a tripod
    Attach the tripod to the lens, not to the camera.
    To change vertical/horizontal position
    Loosen the collar-locking knob on the tripod-mounting collar (1) and rotate the camera either
    direction. The camera can be quickly switched between vertical and horizontal positions while
    maintaining stability when using a tripod.
    Gray indexes (collar indexes) are located at 90° intervals on the tripod-mounting collar. Align a
    gray index on the tripod-mounting collar with the gray index (collar index) on the lens to adjust the
    camera position precisely (2).
    Tighten the collar-locking knob firmly after the camera position is set.
    To detach the tripod-mounting collar
    The tripod-mounting collar can be detached.
    1 Remove the lens from the camera.
    See “ Attaching/detaching the lens” for details.
    2 Loosen the collar-locking knob (1).
    3 Rotate the tripod-mounting collar to align the red index on the tripod-
    mounting collar (collar mounting index next to SET/RELEASE) with the
    orange index on the lens (mounting index) (3).
    4 Move the tripod-mounting collar towards the lens mount and detach the tripod-mounting collar from the lens (4).
    Condensation
    If your lens is brought directly from a cold place to a warm place,
    condensation may appear on the lens. To avoid this, place the lens in a plastic
    bag or something similar. When the air temperature inside the bag reaches
    the surrounding temperature, take the lens out.
    Cleaning the lens
    Do not touch the surface of the lens directly.
    If the lens gets dirty, brush off dust with a lens blower and wipe with a soft,
    clean cloth (Cleaning Cloth KK-CA (optional) is recommended).
    Do not use any organic solvent, such as thinner or benzine, to clean the lens or
    the camera cone.
Sony SAL-70200G

Brauchen Sie Hilfe?

Anzahl der Fragen: 0

Haben Sie eine Frage zum Sony SAL-70200G oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere Sony SAL-70200G-Eigentümer Ihre Frage richtig beantworten.

Sehen Sie sich hier kostenlos das Handbuch für an. Dieses Handbuch fällt unter die Kategorie und wurde von Personen mit einem Durchschnitt von bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: . Haben Sie eine Frage zum oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Sony SAL-70200G-Spezifikationen

Marke Sony
Model SAL-70200G
Produkte Objektiv
Sprache Englisch
Dateityp PDF
Gewicht und Abmessungen
Gewicht 1340
Länge (mm) 196.5
Durchmesser (mm) 87
Filtergröße 77
Sonstige Funktionen
Vergrößerung 0.21
Linsensystem
Brennweitenbereich 70 - 200
Blendenlamellen 9
Naheinstellgrenze 1.2
Minimale Blendenzahl 2.8
Kameralinse entspricht 35 mm 105 - 300
Objektiv-Struktur 19/16
Maximale Blendenzahl 32
Komponente für MILC
Linsen Typ Teleobjektiv
Interner Fokus (IF)
Linsen Montageanschluss Sony A
Bildsensor Format Vollrahmen
Design
Produktfarbe Black, White
Befestigungstyp Bajonett

Verwandte Produkthandbücher

Objektiv Sony

Diese Website benutzen Cookies. Wenn Sie die Website weiter nutzen, stimmen Sie der Verwendung von Cookies zu.

Erfahren Sie mehr