Uni-T UT204 Bedienungsanleitung

Uni-T UT204
8.5 · 4
PDF Bedienungsanleitung
 · 2 Seiten
Englisch
BedienungsanleitungUni-T UT204

Overview

This Operating Manual covers information on safety and cautions. Please read the
relevant information carefully and observe all the Warnings and Notes strictly.
Warning
To avoid electric shock or personal injury, read the “Safety Information” carefully
before using the Meter.
Model UT203/204 (hereafter referred to as "the Meter") is 4000-count stable, safe
and reliable digital clamp multimeter. They are designed with large-scale integrated
circuits and A/D converter as the core as well as the overload protection and novel
structure, which make them a superb tool for electricians.
The Meter can not only measure AC/DC Voltage, AC/DC Current, Frequency, Duty
Cycle, Resistance, Diodes, Continuity but also it has Data Hold, Sleep Mode and
Relative Mode features.
UT204 has an extra True RMS feature.

Unpacking Inspection

Open the package case and take out the Meter. Check the following items carefully
for any missing or damaged part:
Item Description Qty
1
2
3
4
English Operating Manual
Test Leads
Carrying Bag
9V Battery (NEDA1604, 6F22 or 006P)
1 pc
1 pair
1 pc
1 pc
In the event you find any missing or damaged part, please contact your dealer
immediately.

Safety Information

This Meter complies with the standard IEC61010: Pollution Degree 2, Overvoltage
Category (CAT. II 600V, CAT. III 300V) and Double Insulation.
CAT. II: Local level, appliance, PORTABLE EQUIPMENT etc., with smaller transient
overvoltages than CAT. III.
CAT. III: Distribution level, fixed installation, with smaller transient overvoltages than
CAT. IV
Use the Meter only as specified in this operating manual, otherwise the protection
provided by the Meter may be impaired.
In this manual, a Warning identifies conditions and actions that pose hazards to the
user, or may damage the Meter or the equipment under test.
A Note identifies the information that user should pay attention to.
Warning
To avoid possible electric shock or personal injury, and to avoid possible damage
to the Meter or to the equipment under test, adhere to the following rules:
or the case (or part of the case) is removed. Look for cracks or missing plastic.
Pay attention to the insulation around the connectors.
Inspect the test leads for damaged insulation or exposed metal. Check the test
leads for continuity. Replace damaged test leads with identical model number
or electrical specifications before using the Meter.
Do not apply more than the rated voltage, as marked on the Meter, between the
terminals or between any terminal and grounding. If the value to be measured
is unknown, use the maximum measurement position and reduce the range step
by step until a satisfactory reading is obtained.
When measurement has been completed, disconnect the connection between
the test leads and the circuit under test, remove the testing leads away from the
input terminals of the Meter and turn the Meter power off.
Before using the Meter inspect the case. Do not use the Meter if it is damaged
The rotary switch should be placed in the right position and no any changeover
of range shall be made when measurement is conducted to prevent damage of
the Meter.
Do not carry out the measurement when the Meter’s back case and battery
compartment are not closed to avoid electric shock.
Do not input higher than 600V between the two Meter’s input terminal to avoid
electric shock and damages to the Meter.
When the Meter is working at an effective voltage over 60V in DC or 30V rms in
AC, special care should be taken for there is danger of electric shock.
Use the proper terminals, function, and range for your measurements.
Do not use or store the Meter in an environment of high temperature, humidity,
explosives, inflammables and strong magnetic field. The performance of the
Meter may deteriorate after dampened.
When using the test leads, keep your fingers behind the finger guards.
Disconnect circuit power and discharge all high-voltage capacitors before testing
resistance, continuity and diode.
Replace the battery as soon as the battery indicator appears. With a low
battery, the Meter might produce false readings that can lead to electric shock
and personal injury.
When servicing the Meter, use only use the replacement parts with the same
model or identical electrical specifications.
The internal circuit of the Meter shall not be altered at will to avoid damage to
the Meter and any accident.
Soft cloth and mild detergent should be used to clean the surface of the Meter
when servicing. No abrasive and solvent should be used to prevent the surface
of the Meter from corrosion, damage and accident.
The Meter is suitable for indoor use.
Turn the Meter off when it is not in use and take out the battery when not using
for a long time.
Constantly check the battery as it may leak when it has been using for some time,
replace the battery as soon as leaking appears. A leaking battery will damage
the Meter.

Safety Information

AC (Alternating Current)
DC (Direct Current)
AC or DC
Grounding
Double Insulated
Warning. Refer to the Operating Manual
Low Battery Indication
Continuity Test
Diode
Fuse
Risk of Electric Shock
Conforms to Standards of European Union

The Meter Structure (See Figure 1)

Figure 1
Input Terminals
LCD Display
Functional Buttons
Rotary Switch
Trigger: press the lever to open the transformer
jaws. When the pressure on the lever is released,
the jaws will close.
Hand Guards: to protect user’s hand from touching
the dangerous area.
Transformer Jaw: designed to pick up the AC and
DC current flowing through the conductor. It could
transfer current to voltage. The tested conductor
must vertically go through the Jaw center.
1.
2.
3.
4.
5.
6.
7.

Functional Buttons

Below table indicated for information about the functional button operations.
Button Description
Press HOLD to enter the Hold mode in any mode, the Meter beeps.
Press HOLD again to exit the Hold mode, the Meter beeps.
At
and
range:
Press to select manual ranging measurement mode. The Meter
is default to auto ranging measurement mode.
When the Meter is at manual ranging measurement mode, press
to step down the range.
At
range:
Press to enter the REL mode.
It subtracts a stored value from the present measurement value
and displays a result.
At Hz/Duty% range:
Press to switch between Hz measurement mode and Duty %
measurement mode.
HOLD
REL
V
A
SELECT
Press SELECT button to select the alternate functions marked in
blue colour on the Meter’s faceplate including
,
,
40 ,
and
400
.
After the Meter entering Sleep Mode, press and hold SELECT to
turn the Meter on, it will disable the Sleep Mode feature.
V
A A

The Effectiveness of Functional Buttons

Not every functional buttons can be used on every rotary switch positions. Below
table describe which functional buttons can be used on which rotary switch positions
Rotary Switch
Positions
Functional Buttons
SELECT
REL
HOLD
N/A
N/A
N/A
V
Hz / Duty%
40A
400A
/

Display Symbols (See Figure 2)

Figure 2
4
1
2
3
5
6
8 9
10
12
13
14
16
7
11
15

Measurement Operation

A. Measuring DC/AC Voltage (See Figure 3)
Figure 3
Warning
To avoid harm to you or damage to the Meter
from eletric shock, do not attempt to measure
voltages higher than 600V AC/DC, although
readings may be obtained.
The DC Voltage ranges are:
400mV, 4V, 40V, 400V and 600V.
The AC Voltage ranges are:
4V, 40V, 400V and 600V.
To measure DC/AC voltage, connect the Meter as follows:
Insert the red test lead into the Hz Duty% terminal and the black test lead
into the COM terminal.
1.
Red Black
When DC/AC voltage measurement has been completed, disconnect the connection
between the testing leads and the circuit under test and remove testing leads from
the input terminals.
Set the rotary switch to . DC mesaurement mode and auto ranging is a default.
Press SELECT to switch to AC measurement mode or press to switch to
manual ranging measurement mode.
Connect the test leads across with the object being measured.
The measured value shows on the display.
2.
3.
V
REL
Note
B. Measuring Resistance (See Figure 4)
Figure 4
Red Black
Warning
To avoid damage to the Meter or to the devices
under test, disconnect circuit power and discharge
all the high-voltage capacitors before measuring
resistance.
The resistance ranges are:
400
, 4k , 40k ,400k ,4M and 40M .
To measure resistance, connect the Meter as follows:
Insert the red test lead into the Hz Duty%
terminal and the black test lead into the
COM terminal.
1.
2.
3.
Set the rotary switch to . Resistance measurement is default to auto range mode,
press to switch to manual ranging measurement mode.
Connect the test leads across with the object being measured.
The measured value shows on the display.
REL

Rotary Switch

Below table indicated for information about the rotary switch positions.
Rotary Switch Position
Power is turned off
AC or DC voltage measurement
Resistance measurement
: Diode test
: Continuity test
Frequency Measurement and Duty
Measurement
AC and DC current measurement range
Function
OFF
V
Hz / Duty%
40A 400A
&
/
10
11
12
13
14
15
16
,k ,M
Hz
A
mV, V
TRMS
OL
: Ohm. The unit of resistance.
k
: Kilohm. 1x10
3
or 1000 ohms
M
: Megohm. 1x10
6
or 1,000,000 ohms
The unit of Frequency
Amperes (amps). The unit of current.
Volts. The unit of voltage.
mV: Millivolt. 1x10
-3
or 0.001 volts
Indicates negative reading
Indicator for TRMS mode
The input value is too large for the selected range
Number Description
1
2
3
4
5
6
7
8
9
AC
DC
Symbol
Indicator for AC voltage or current
Indicator for DC voltage
The battery is low.
Warning: To avoid false readings, which could lead to
possible electric shock or personal injury, replace the
battery as soon as the battery indicator appears.
The Meter is in the auto range mode in which the Meter
automatically selects the range with the best resolution.
Test of diode
The continuity buzzer is on
Indicator for Duty.
Data hold is active
Indicator for REL mode
%
To obtain a more precise reading, you could remove the objects being tested from
the circuit when measuring.
When resistance measurement has been completed, disconnect the connection
between the testing leads and the circuit under test and remove testing leads from
the input terminals.
Note
C. Testing Diodes (See Figure 5)
Warning
To avoid damage to the Meter or to the devices
under test, disconnect circuit power and discharge
all the high-voltage capacitors before testing
diodes.
Use the diode test to check diodes, transistors, and
other semiconductor devices. The diode test sends
a current through the semicondutor junction, then
measure the voltage drop across the junction. A
good silicon junction drops between 0.5V and 0.8V.
To test the diode out of a circuit, connect the Meter
as follows:
Insert the red test lead into the Hz Duty% terminal and the black test lead
into the COM terminal.
1.
Figure 5
Red Black
To obtain a more precise reading, you could remove the objects being tested from
the circuit when measuring.
When diode testing has been completed, disconnect the connection between the
testing leads and the circuit under test and remove testing leads from the input
terminals.
Set the rotary switch to . Diode measurement mode is a default or presss
SELECT to select measurement mode.
For forward voltage drop readings on any semiconductor component, place the
red test lead on the component’s anode and place the black test lead on the
component’s cathode.
2.
3.
Note

Bedienungsanleitung

Sehen Sie sich hier kostenlos das Handbuch für Uni-T UT204 an. Dieses Handbuch fällt unter die Kategorie Multimeter und wurde von 4 Personen mit einem Durchschnitt von 8.5 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Uni-T UT204 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Brauchen Sie Hilfe?

Haben Sie eine Frage zum Uni-T UT204 und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Uni-T UT204-Besitzer, Ihnen eine gute Antwort zu geben.

Anzahl der Fragen: 0

Uni-T UT204-Spezifikationen

Nachfolgend finden Sie die Produktspezifikationen und die manuellen Spezifikationen zu Uni-T UT204.

Allgemeines
Marke Uni-T
Model UT204
Produkte Multimeter
Sprache Englisch
Dateityp Benutzerhandbuch (PDF)

Häufig gestellte Fragen

Finden Sie die Antwort auf Ihre Frage nicht im Handbuch? Vielleicht finden Sie die Antwort auf Ihre Frage in den FAQs zu Uni-T UT204 unten.

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Keine Ergebnisse