Vtech VSP500A Bedienungsanleitung

Vtech VSP500A
(1)
  • Anzahl Seiten: 2
  • Dateityp: PDF
Parts checklist
Your headset package contains the following
items. Save your sales receipt and original
packaging in the event warranty service is
necessary.
Headset overview
1 – VOL+/VOL-
• Push to right or left to adjust the ringer volume
while in idle mode, or the listening volume while on
a call.
2 – MUTE/FLASH
• Press to mute the ringer in the earpiece when
there is an incoming call.
• Press to mute the microphone during a call.
• Press and hold for two seconds to answer an
incoming call when you receive a call waiting
alert during a call.
3 –
• Press to make, answer or end a call.
4 – Microphone
5 – Battery pack
• Open to replace the battery pack.
6 – Earpiece
Charger overview
1 – Magnetic charging mount
• Place the headset here for charging.
2 – Power cord slot
3 – Power jack
Light and alert tones overview
Light:
light status
Red • On when the headset is charging in the
headset charger.
• Flashes every 10 seconds to indicate
the battery is low when the headset is
not in the headset charger.
• Flashes three times to indicate the
headset is powering off.
Blue • On when a fully charged and registered
headset is in the headset charger.
• Flashes three times to indicate the
headset is powering on.
• Flashes twice every three seconds
when the headset is in use.
• Flashes four times every four seconds
when there is an incoming call.
• Flashes every 10 seconds when a fully
charged and registered headset in idle
mode is out of the headset charger.
Red
and
blue
• Flashes slowly when the headset is not
registered.
• Flashes quickly when the headset is
trying to register to a telephone base.
Off • No battery is installed or out of battery.
• The headset is powered off.
Alert tones:
One short beep Headset key tone.
One short beep
every 30 seconds
Muted headset microphone
alert tone.
Two beeps • Error alert tone.
• The ringer volume is at its
lowest setting.
• The listening volume is at
its highest or lowest setting.
• Any key is pressed while
the headset is out of range
Two low beeps Call waiting alert tone.
Two rapid beeps
every 20 seconds
Low battery warning.
Three rising beeps A conference call starts.
Three rapid beeps
every 20 seconds
• The headset is out of range.
• The headset is not yet
registered.
Ring tone • Incoming call alert tone.
• Ring back tone.
Three rapid beeps The headset is powering on
or off.
Install the battery
NOTE
• The battery is permanently attached to the battery
compartment cover (known as the battery pack). Do
not try to separate them from each other.
Install the battery as shown below.
NOTES
• Use only the supplied battery.
• Remove any headset attachment (earbud excluded)
before battery replacement.
• If the headset will not be used for a long time,
remove the battery to prevent possible leakage.
• To purchase a replacement battery pack (model
BT191665), visit our website at smbphones.vtech.
com or call 1 (888) 370-2006.
Connect and charge the battery
NOTES
• Use only the supplied adaptor.
• Charge the battery provided with or identified for
use with this product only in accordance with the
instructions and limitations specified in this manual.
Connect the chargerCharge the battery
The light turns on when the headset is
charging.
NOTES
• For best performance, keep the headset in the
charger when not in use.
• The battery is fully charged after three hours of
continuous charging.
• When fully charged, the headset battery provides
approximately 12 hours of talk time or 5 days of
standby time.
Before use
Add and register a headset
You can add new
VSP500A
headset (purchased
separately) to your VSP725A or VSP735A
telephone system. Your VSP725A or VSP735A
telephone system supports one headset only.
Register the headset with the telephone base
before use. After charged, the light on headset
flashes in red and blue slowly and alternately.
NOTE
• Charge the new headset without interruption for
at least 30 minutes before registering it to the
telephone base.
To register a headset:
1. Remove the headset from the charger.
2. Press Menu at the telephone base when idle.
3. Press q to highlight User Settings, and then
press SELECT.
4. Press q to highlight DECT headset, and
then press SELECT.
5. With Register highlighted, press SELECT on
the telephone base.
6. Place the headset back to the charger. The
light flashes quickly in red and blue.
It takes about 60 seconds to complete the
registration process. The light turns red when
the headset is registered but not fully charged,
or turns blue when it is registered and fully
charged.
To verify the registration, press the button on
the headset and check for a dial tone. If the
registration fails, you hear the voice prompt “Not
registered” and the light on the headset flashes
slowly in red and blue.
To reset the headset, remove it from the headset
charger and repeat the registration process
again.
Deregister a headset
To replace a headset or register the headset to
another telephone base, you must deregister
all devices, and then register each device
individually.
To deregister all devices:
1. Press Menu at the telephone base when idle.
2. Press q to highlight User Settings, and then
press SELECT.
3. Press q to highlight DECT headset, and
then press SELECT.
4. Press q to highlight Deregister, and then
press SELECT.
The light flashes slowly in red and blue when
the deregistration process is successful. It takes
about 10 seconds to complete the deregistration
process.
Position the headset
You can choose a suitable size of earbud and an
appropriate way to position your headset.
Earbud
There are three sizes of earbuds provided. The
medium-sized earbud is already attached to the
headset.
To remove the earbud from the headset earpiece:
• Hold both sides of the earbud. Twist and
pull the earbud until it separates from the
earpiece.
To attach the earbud to the headset earpiece:
1. Choose an appropriate earbud.
2. Position the earbud on the earpiece.
3. Press the earbud down on the earpiece until
it clicks into place. Move the earbud around
so that the protruding bump on the earbud is
pointing towards your mouth when placed in
your ear.
Over the ear hook
There are two sizes of ear hooks. You can
choose the suitable ear hook to attach to the
headset.
To adjust the headset to wear on the left or right ear:To attach the ear hook to the headset:
1. Remove any headset attachment (earbud
excluded) currently connected to the headset.
2. Insert the earpiece into the ear hook ring.
3. Press the edge of the ear hook ring towards
the earpiece until it clicks into place.
4. Hook the headset onto the desired ear.
Adjust the angle of the headset until the
microphone is pointing towards your mouth.
To remove the ear hook from the headset:
• Hold the headset with one hand. Twist and
pull the ear hook with your other hand until it
separates from the earpiece.
Over the head bandTo attach the head band to the headset:
1. Remove any headset attachment (earbud
excluded) currently connected to the headset.
2. Insert the earpiece into the loop of the ear pad.
3. Push the earpiece towards the loop of the
ear pad until it clicks into place.
4. Adjust the head band to fit your head. Adjust
and rotate the angle of the headset until the
microphone is pointing towards your mouth.
To remove the head band from the headset:
• Hold the headset with one hand and the ear
pad with your other hand. Twist and pull the
headset until it separates from the loop of the
ear pad.

Congratulations

on purchasing your new VTech product. Before
using this telephone, please read Important
safety instructions.
This manual has all the feature operations and
frequently asked questions necessary to install
and operate your new VTech product. Please
read this manual thoroughly to ensure proper
installation and operation of this VTech product.
• Cordless headset
with medium-sized
earbud attached
User’s manual
• Headset charger
• Battery pack
(with battery
compartment cover
attached)
• Headset charger
power adapter
• Earbud x5 • Over the ear hook
x2
• Over the head band • Behind the neck
band
• User’s manual
1
2
3
4
5
6
1
2
3
• To wear on the
left ear
• To wear on the
right ear
For customer service or warranty service,
please contact our regional offices / distributors
in the country or region where you purchase
VSP735A.

Quick Start Guide

VSP500A
ErisTerminal™ DECT SIP Cordless Headset
for use with VSP725A/VSP735A
Vtech VSP500A

Brauchen Sie Hilfe?

Anzahl der Fragen: 0

Haben Sie eine Frage zum Vtech VSP500A oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere Vtech VSP500A-Eigentümer Ihre Frage richtig beantworten.

Sehen Sie sich hier kostenlos das Handbuch für Vtech VSP500A an. Dieses Handbuch fällt unter die Kategorie Kopfhörer und wurde von 1 Personen mit einem Durchschnitt von 5.1 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Vtech VSP500A oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Vtech VSP500A-Spezifikationen

Allgemeines
Marke Vtech
Model VSP500A
Produkte Kopfhörer
EAN 735078035936
Sprache Englisch
Dateityp PDF
Gewicht und Abmessungen
Gewicht 72 g
Tiefe 85.1 mm
Höhe 131 mm
Breite 57.7 mm
Leistungen
Kompatible Produkte VTech VSP725A / VSP735A
Lautstärkeregler Digital
Operationsschlüssel Volume +,Volume -
Produkttyp Kopfhörer
Produktfarbe Holzkohle
Headset-Typ Monophon
Tragestil Ohrbügel
Batterie
Batteriekapazität 240 mAh
Akku Ja
Anzahl unterstützter Batterien 1
Aufladequelle Gleichstrom
Betriebsbedingungen
Temperaturbereich in Betrieb 0 - 50 °C
Verpackungsdaten
Paketgewicht 415 g
Verpackungshöhe 145 mm
Verpackungsbreite 160 mm
Verpackungstiefe 114 mm
Verpackungsart Box
Lieferumfang
AC-Netzadapter Ja
Extra Ohrknöpfe Ja
Ladegerät Ja
Mikrofon
Mikrofon Stummschaltung Ja
Aktive Geräuschunterdrückung Ja
Sonstige Funktionen
Abmessungen von Kiste/Umkarton (B x T x H) 339 x 245 x 195 mm
Benutzerhandbuch Ja
Technische Details
Optionaler Ohrbügel 2
Anschlüsse und Schnittstellen
Kabellose Reichweite 150 m
Übertragungstechnik Kabellos
Kopfhörer
Schalldämpfung Ja
Position Kopfhörerlautsprecher Im Ohr
Mehr anzeigen

Häufig gestellte Fragen

Nachfolgend finden Sie die am häufigsten gestellten Fragen zu Vtech VSP500A .

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage