Walrus Audio Slötvå Multi Texture Reverb Bedienungsanleitung

Walrus Audio Slötvå Multi Texture Reverb
7.2 · 1
PDF Bedienungsanleitung
 · 2 Seiten
Englisch
BedienungsanleitungWalrus Audio Slötvå Multi Texture Reverb
CONTROLS:
DECAY – Adjusts the length of the reverb decay. Go from tight short reverb,
at full counter-clockwise, to long drawn out texture at full clockwise.
FILTER – Controls the tone of the reverb decay. Each algorithm includes
a low-pass fi lter optimized for that unique sound and the knob controls
the fi lter cutoff frequency. Turn the knob up to open the fi lter for brighter
tones, and down to close the fi lter resulting in a darker tone.
MIX – Turn counter-clockwise for increased dry signal, and clockwise for
more reverb. Use the white line to reference approximately equal parts dry
and reverb. Since this point is around 2 o’clock, it gives a greater range of
adjustment of your mix ratio below the 50/50 point making it easier to dial
in the perfect amount of reverb.
X – The X knob changes jobs depending on which algorithm is selected.
DARK – Sets the level of a -1 octave signal that feeds the reverb.
RISE – Sets the amount of time it takes the reverb to swell in
after a note is played. Set lower for shorter rise times and higher
for longer rise times.
DREAM – Sets the depth of vibrato applied to the reverb decay.
DEPTH – Controls the amount of modulation applied to the reverb decay. Go from no modulation, to
nightmare inducing pitch bending at high settings.
Secondary Function: Rate - Controls the speed of the modulation applied to the reverb decay.
ALGORITHM SWITCH – The toggle switch selects one of three onboard reverb algorithms.
Secondary Function: Wave Shape selection.
REVERB MODES: Use the toggle switch to select one of three onboard algorithms.
DARK Add a lower octave to your reverb trail. Create deep and wide atmospheric sounds and channel
nightmarish soundscapes. X knob sets the level of a -1 octave signal that feeds the reverb.
RISE – Auto-swell reverb for beautiful cinematic swells. Don’t rush it. Let it breathe and gently wake up. X
knob sets the amount of time it takes the reverb to swell in after a note is played. Set lower for shorter rise
times and higher for longer rise times. Note: Rise works best in front of an amp, not through an FX loop.
DREAM – Lush reverb with a latching pad function. Press the sustain switch to latch signal. Experiment
with the X knob to add vibrato over the pad. Press sustain again and pad will decrescendo according to
where decay knob is set. X knob sets the depth of vibrato applied to the reverb trail.
MODULATION WAVE SHAPES:
SINE Smooth and even pitch up and down modulation.
WARP – Asymmetric pitch up modulation similar to a warped record.
SINK – Asymmetric pitch down modulation for sinking detune similar to a Bigsby.
BYPASS – Turns the effect on and off. It also features our smart bypass switching. When the switch is in off
position, press and hold to temporarily activate the effect to add a moment of reverb texture. Releasing
the switch turns the effect off, and fades it out.
SUSTAIN – When pressed, the decay switch ramps up the reverb trail to maximum creating long dreamy
reverb trail and then ramps back down to the decay knob setting when released. In the “Dream” algorithm,
the sustain switch is latching. Press it once to capture and sustain the current reverb decay for extremely
long pad-like sounds. Press it again to let the reverb trail taper off, based on the position of the decay knob.
SECONDARY FUNCTIONS – To access the secondary functions, with the pedal engaged, hold down the
bypass switch and use the toggle to select the desired wave shape, and the depth knob to set the desired
rate. The bypass LED will fl ash at the rate of modulation while in the secondary mode. The pedal remembers
the wave shape and rate settings for the current preset when saved, until the next time they are modifi ed.
The pedal also maintains the algorithm and depth setting when modifying secondary functions.
more reverb. Use the white line to reference approximately equal parts dry
and reverb. Since this point is around 2 o’clock, it gives a greater range of

WALRUSAUDIO.COM

TRAILS MODE The Slötvå can run in trails or no trails mode. In trails mode, when you turn the pedal off,
the reverb decay dies off naturally. In no trails mode, the decay is abruptly cut off when you turn the pedal
off. To toggle between either mode, hold down the bypass switch for 1 second while applying power to
the pedal. Unplug power and repeat to toggle to the other mode. Default is Trails mode.
Presets - Slötvå has 3 on-board presets (Red, Green, Blue). If the same algorithm is used in the next preset,
the reverb sound will fade into the saved settings.
Scroll through the presets by pressing both stomp switches at the same time. Each press of both stomp
switches will load the next preset until you get back to red and the pattern of Red, Green, Blue repeats.
To save a preset:
1. Scroll to the preset color you want to save a new sound.
2. Using the knobs and switches, dial in the desired reverb sound. The preset LED will turn purple
indicating the preset has been modifi ed. The preset LED will go back to the preset color when you cross
the current saved setting.
3. To save, hold down the Bypass and Tap switches until the preset LED blinks. The preset is now saved
and the LED will return to the preset color.
FACTORY RESET To perform a factory reset, hold down both foot switches while plugging in power to
the pedal. Hold both switches until the Preset LED starts to fl ash, then release both switches. The pedal
will now be in Trails mode with the three default presets loaded in the Red, Green and Blue presets.
The default wave shape are as follows: Dark - Sink // Rise - Sine // Dream - Sink.

Sehen Sie sich hier kostenlos das Handbuch für Walrus Audio Slötvå Multi Texture Reverb an. Dieses Handbuch fällt unter die Kategorie Nicht kategorisiert und wurde von 1 Personen mit einem Durchschnitt von 7.2 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Walrus Audio Slötvå Multi Texture Reverb oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Brauchen Sie Hilfe?

Haben Sie eine Frage zum Walrus Audio und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Walrus Audio -Besitzer, Ihnen eine gute Antwort zu geben.

Anzahl der Fragen: 0

Allgemeines
Walrus Audio
Slötvå Multi Texture Reverb
Nicht kategorisiert
Englisch
Benutzerhandbuch (PDF)

Finden Sie die Antwort auf Ihre Frage nicht im Handbuch? Vielleicht finden Sie die Antwort auf Ihre Frage in den FAQs zu Walrus Audio Slötvå Multi Texture Reverb unten.

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Keine Ergebnisse

Bedienungsanleitu.ng

© Copyright 2023 Bedienungsanleitu.ng. Alle Rechte vorbehalten.