Whirlpool AWOE 9759 Bedienungsanleitung

Whirlpool AWOE 9759
(1)
  • Anzahl Seiten: 2
  • Dateityp: PDF

5019 301 06276

Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as described in
the chapter “Detergent and Additives” in your Instructions for Use.
Turn the programme selector to the desired programme; the light
of the
“Start (Pause)”
button blinks. The
temperature
and
spin
speed
indicated on the display can be altered by pressing the
“Temperature” button or the “Spin speed” button.
When the combination of programme and additional option(s) is
not possible, the indication lights switch off automatically.
Unsuitable combinations of options are deselected automatically.
“Prewash” button
Only for heavily soiled loads (for example sand, granular dirt)
sensible. Increases the cycle time by approximately 15 min.
Do not use liquid detergent for the main wash when activating
the “Prewash” option.
“Clean+” button
Choose this option if you use an in-wash additive for stain removal
(powder, for example “Vanish”) - it will optimize the additive’s
efficiency to get better wash performance and stain removal.
Choose temperature of 30 or 40°C and use with maximum load.
Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together with
your detergent (only use powder detergent with this option).
Respect the manufacturer’s dosing instructions.
Prolongs the programme by approx. 10 to 15 minutes.
Appropriate for use of stain removers and bleaches on oxygen
basis.
Chlorine or perborate bleaches must not be used!
“Easy ironing” button
Makes ironing easier by an increased water quantity and a very
gentle spin.
“Intensive rinse” button
More water is added and rinse cycle is prolonged.
This option is particularly suitable for areas with very soft water or
for washing baby linen, and helps people with allergies.
“Spin speed” button
Every programme has a predefined spin speed.
Press the button to set another spin speed.
If spin speed “0” is selected, the final spinning is cancelled but
intermediate spin peaks remain during rinse. The water is
drained out only.
If you select “Rinse hold” , the laundry remains in the last
rinse water without progressing to the final spin cycle, to avoid
creasing and prevent colours from changing. To activate the
“Rinse hold”, press the “Spin speed” button repeatedly until the
“Rinse hold” symbol on the display lights up.
- The wash programme stops to “Rinse hold” when the
“Rinse hold” symbol on the display blinks; the light of
“Start (Pause)”
button blinks as well.
- To terminate the “Rinse hold” by draining the water,
without any spinning, press the
“Start (Pause)”
button.
- To terminate the “Rinse hold” by spinning the laundry, press
the “Spin speed” button to select the desired spin speed and
then
“Start (Pause)”
to start the spin cycle.
- Do not leave the laundry to soak for too long in the “Rinse hold”.

CONSUMPTION DATA

Programme

Temperature

(°C)
Load
(kg)

Water

(l)

Energy

(kWh)

Approx. Programme Duration

(hours : minutes)

*

95 9.0 87

**

2.60 2:10

Cotton

***

60 9.0 64 1.53 2:20

Cotton 40 9.0 82 0.80 2:05

Synthetics 60 3.5 46

**

0.85 1:35

Synthetics 40 3.5 42 0.50 1:20

Delicates 30 2.5 60 0.40 0:45

Wool 40 2.0 60 0.60 0:45

40 2.0 45 0.60 0:40

Jeans 40 7.0 95 0.85 2:21

Big Items 40 3.0 74 0.75 1:30

Sport 30 3.5 54 0.55 1:34

60 9.0 80 1.08 4:00

40 6.0 73 0.60 1:00

30 3.0 30 0.20 0:15

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The time indicated on the display can deviate from the values in the table, because it takes into account the operation conditions
applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

If there is a programme setting which you use frequently, the
appliance offers the possibility to save one setting for each
programme so that it can be used again by just pushing one button.
Select the desired programme, temperature, spin speed and
option(s), push and hold the
“Favourites”
button for at least
3 seconds. The lamp next to
“Favourites”
shortly blinks and
then lights up - the programme setting is saved.
Next time you want to use your individual programme setting,
select the programme, push the
“Favourites”
button and start by
pushing
“Start (Pause)”
.
If you want to replace the saved programme setting by another
one, proceed as already described above.
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper. Do
not use liquid detergent when activating the “Start delay”.
Select programme, temperature, spin speed and options.
Press the Start delay button to select one of the delay time
steps between 0:30 and 23:00 hours.
•Press the
“Start (Pause)”
button.
The countdown of the delay time begins; the clock symbol next to
the delay time and the colon between hours and minutes blink.
The time delay indication disappears when the programme
starts and it is replaced by the remaining programme time.
To cancel the “Start delay
..before you press the “Start (Pause)” button:
Press the
“Reset / Drain”
button, or set the start delay time to
“0:00” - the delay time disappears after a few seconds.
..after having pressed the “Start (Pause)” button:
Press the
“Reset/Drain”
button for at least 3 seconds; the start
delay time disappears from the display. Or press
“Start (Pause)”
twice to start the selected programme immediately.
Before starting a programme, the symbol lights to show that the
door can be opened to add more washing. As soon as you press
“Start (Pause)”
, the door will lock until the end of the
programme and must on no account be forced open. In case you
have to open it urgently during a running programme, refer to
“Reset a running programme before the end”.
If you try to start a wash programme and the door is not properly
closed, the “Add garment” indication will blink.
Open the tap and press the
“Start (Pause)”
button; the blinking
“Start (Pause)”
button light becomes constant. The “Add
garment” indication goes out, and the lit bubbles indicate that the
programme is in process. In some phases, the remaining
programme time is newly calculated - if this is the case, the “6
th
sense” indication on the display will fade, and the remaining
programme time is replaced by an animation.
Activating the child lock prevents children from starting a wash
cycle or changing the settings of a running programme. The child
lock cannot be activated or deactivated when the programme
selector is in the “Off/O” position. To activate the child lock:
Turn the programme selector to a programme position, or run
a programme as usual.
Press the “Temperature” and the “Spin speed” button
simultaneously for at least 3 seconds. The “Child lock” symbol
will shortly blink and then light up to indicate that the
child lock is active.
The programme setting cannot be changed anymore; the only change
possible is to switch the washer off by turning the programme selector
to the “Off/O” position. To deactivate the child lock, proceed in the
same way as for activating it.
If one of the red failure indications on the display lights up, refer to
the “Troubleshooting Guide” in your “Instructions for Use”.
The display shows “End”, and the “Programme finished”
indication lights up.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
Leave the door ajar to allow the drum to dry.
If you do not turn the programme selector to the “Off / O
position, all lights of the control panel go out after a few
minutes to save energy - only “End” will remain on the display.
The symbol will blink at the end of the programme if you used too
much detergent. Use less detergent next time.
1. Press the
“Start (Pause)”
button to pause the programme.
The light blinks.
2. Select the new programme, temperature, any options and
another spin speed if you want.
3. Press the
“Start (Pause)”
button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add detergent
for this programme.
The
“Reset/Drain
button cancels a programme before the end.
•Press the
“Reset/Drain”
button for at least 3 seconds; an
animation appears on the display. Any existing water is drained
out before the door can be opened.

SAVE YOUR FAVOURITE PROGRAMMES

START DELAY

ADD GARMENT” INDICATION

PROGRAMME START

CHILD LOCK

RED FAILURE INDICATIONS

PROGRAMME END

DETERGENT OVERDOSAGE INDICATION

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

RESET A RUNNING PROGRAMME BEFORE

THE END

30106276GB.fm Page 2 Thursday, April 23, 2009 5:56 PM
Black process 45.0° 150.0 LPI
Whirlpool AWOE 9759

Brauchen Sie Hilfe?

Anzahl der Fragen: 0

Haben Sie eine Frage zum Whirlpool AWOE 9759 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je detaillierter Sie Ihr Problem und Ihre Frage angeben, desto einfacher können andere Whirlpool AWOE 9759-Eigentümer Ihre Frage richtig beantworten.

Sehen Sie sich hier kostenlos das Handbuch für Whirlpool AWOE 9759 an. Dieses Handbuch fällt unter die Kategorie Waschmaschinen und wurde von 1 Personen mit einem Durchschnitt von 7.5 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Whirlpool AWOE 9759 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Whirlpool AWOE 9759-Spezifikationen

Allgemeines
Marke Whirlpool
Model AWOE 9759
Produkte Waschmaschine
Sprache Englisch
Dateityp PDF

Häufig gestellte Fragen

Nachfolgend finden Sie die am häufigsten gestellten Fragen zu Whirlpool AWOE 9759 .

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage