Yamaha RX-V995 Bedienungsanleitung

Yamaha RX-V995
7.5 · 1
PDF Bedienungsanleitung
 · 88 Seiten
Englisch
BedienungsanleitungYamaha RX-V995
10
8
A/B/C/D/E button
Press this button to select a group (A–E) of preset stations.

9 SPEAKERS switches

Press the switch A or B (or both) for the main speakers you will
use to select them. Press the switch for the main speakers you
will not use again to cancel them. On the display panel,
“SPEAKERS A” and/or “SPEAKERS B” will be illuminated,
depending on which main speakers are being selected.

0 Preset station number selector buttons

Select a preset station number (1 to 8).

A BASS EXTENSION button

Press this button inward (ON) to boost the bass frequency
response at the main left and right channels while maintaining
overall tonal balance. This function is effective for reinforcing
the bass frequencies when a subwoofer is not used.

B TONE BYPASS button

Press this button inward (ON) to bypass the tone (BASS and
TREBLE) control circuitry. This function is used for outputting
pure sound and checking the tone control settings. The tone
control circuitry can be used when this button is released
outward (OFF).

C BASS and TREBLE controls

Rotate these knobs to adjust the low and high frequency
response for the left and right main channels only.

D BALANCE control

This knob controls the sound from the main speakers only.
The balance of the output volume to the left and right main
speakers can be adjusted to compensate for sound imbalances
caused by the speaker location or listening room conditions.

E MEMORY (MAN’L/AUTO FM) button

Use this button to enter a station to memory. Refer to the
section “Manual preset tuning” on page 44 for details.
Hold down this button for more than 3 seconds to start
automatic preset tuning. Refer to page 45 for details.

F EDIT button

This button is used to exchange the places of two preset
stations with each other.

G TUNING MODE (AUTO/MAN’L MONO) button

Press this button to switch the tuning mode between automatic
and manual. To select the automatic tuning mode, press this
button so that the “AUTO” indicator is illuminated on the
display. To select the manual tuning mode, press this button so
that the “AUTO” indicator is not illuminated.

H FM/AM button

Press this button to switch the reception band between FM and
AM.

I REC OUT/ZONE 2 selector

Rotate this knob to select the source for recording to an MD
recorder (or tape deck) or VCR. This setting is independent of
the INPUT SELECTOR setting, except when the REC
OUT/ZONE 2 selector is set to the SOURCE position. Then
the INPUT SELECTOR is used to select the source for
recording to the MD recorder (or tape deck) or VCR.
For a user who made up a dual-room audio/video system
with this unit:
The setting of the REC OUT/ZONE 2 selector controls the
input source for the second room.

J LEVEL button

This button is used to adjust the output level of the center and
rear speakers, and subwoofer. First, press this button (several
times) to select the speaker(s). The name appears on the
display. Then press the + or button (
K
) to change the output
level.

K –/+ button

Adjusts the level of the speaker(s) selected by pressing the
LEVEL button. Moreover, performs setting changes and
adjustments for functions selected by pressing the SET MENU
button (

L).

L SET MENU button

Press this button once or more to select the desired function in
the SET MENU mode.

M TUNING DOWN/UP button

Used for tuning. Press the “UP” side to tune in to a higher
frequency, and press the “DOWN” side to tune in to a lower
frequency.

N PROGRAM selector button

Press this button in the or direction to select a digital
sound field processing program.

O EFFECT button

Press this button to turn on and off the output from the center
and rear speakers. The sound becomes normal 2-channel
when this function is turned off.
However, this does not apply to Dolby Digital or DTS. The
signals at all channels will be distributed to the main channels
and output from the main speakers, even if the output from the
center and rear speakers are turned off, when Dolby Digital or
DTS is decoded.

P VIDEO AUX terminals

Connect an auxiliary video or audio input source unit such as a
camcorder to these terminals. A video unit with a S video
output terminal can be connected to the S VIDEO terminal to
obtain a high resolution picture. The source can be selected
with the INPUT SELECTOR and REC OUT/ZONE 2 selector.

Q INPUT MODE button

Press this button to select how input signals are received from
sources that output two or more types of signals. The “AUTO”,
“DTS” and “ANALOG” modes are available. Refer to page 38
for details.

<China, Singapore and General models only>

The “AUTO”, “D.D.RF”, “DTS”, “DGTL” and “ANALOG” modes
are available for DVD/LD sources.
GETTING STARTED

Bedienungsanleitung

Sehen Sie sich hier kostenlos das Handbuch für Yamaha RX-V995 an. Dieses Handbuch fällt unter die Kategorie Empfänger und wurde von 1 Personen mit einem Durchschnitt von 7.5 bewertet. Dieses Handbuch ist in den folgenden Sprachen verfügbar: Englisch. Haben Sie eine Frage zum Yamaha RX-V995 oder benötigen Sie Hilfe? Stellen Sie hier Ihre Frage

Brauchen Sie Hilfe?

Haben Sie eine Frage zum Yamaha und die Antwort steht nicht im Handbuch? Stellen Sie hier Ihre Frage. Geben Sie eine klare und umfassende Beschreibung des Problems und Ihrer Frage an. Je besser Ihr Problem und Ihre Frage beschrieben sind, desto einfacher ist es für andere Samsung Galaxy A7-Besitzer, Ihnen eine gute Antwort zu geben.

Anzahl der Fragen: 0

Yamaha RX-V995-Spezifikationen

Nachfolgend finden Sie die Produktspezifikationen und die manuellen Spezifikationen zu Yamaha RX-V995.

Allgemeines
Marke Yamaha
Model RX-V995
Produkte Empfänger
Sprache Englisch
Dateityp PDF

Häufig gestellte Fragen

Finden Sie die Antwort auf Ihre Frage nicht im Handbuch? Vielleicht finden Sie die Antwort auf Ihre Frage in den FAQs zu Yamaha RX-V995 unten.

Ist Ihre Frage nicht aufgeführt? Stellen Sie hier Ihre Frage

Keine Ergebnisse